Journal of the Korean Society of Hazard Mitigation
/
v.4
no.3
s.14
/
pp.1-8
/
2004
In this study, the change of the current in the coastal zone before and after the construction of Jeju new harbor was predicted by using the numerical model, which uses Hardy-Cross method. The numerical model was carried out for the present state, before the construction, and the state after the construction, and for the wave direction the NNW direction for winter and NE direction for summer were tested so that the seasonal change may be considered. The computation result shows that a large amount of the wave induced current was occurred when there were high waves coming in from NNW direction before and after the construction. Also, before the construction a longshore current occurred moving from the west to the east at the new harbor construction site so that it formed a rip current in the Hwabuk-dong front sea. And also, after the construction, the tip current produced changed into nearshore circulating current and a small circulating current appeared at the harbor entrance. On the other hand, at Samyang 4each, which is 3.0km away from the new harbor in the NE direction, shows that there was a longshore current occurred from the west to the east, which is in the opposite direction the new harbor, and the effect on the new harbor by sediment transport at Samyang beach is thought to be very small.
As a result of investigating research papers concerning the metal bound rim decoration on four pieces of 'Bowl, white porcelain with impressed floral design and sliver bound rim' and one piece of 'Bowl, white porcelain with sliver bound rim' from among the Jingdezhen white porcelain, which are Sinan remains that are kept in a National museum of Korea. It was found that the material of the bound rim was not silver but tin, and lacquer was used as glue. Based on such a scientific analysis, this study conducted a reproduction test of the manufacturing technique and the bonding method of the metal bound rim attached to the upper tip of the china ware. As a way of reproducing the bound rim, the study was able to discover the best method in terms of the avoidance of loss of materials and the workability out of various cutting methods for tin plates, and it also discovered that the use of lacquer in mixture with soil showed a better workability than the use only of a lacquer ingredient in a test of the bonding method of a metal bound rim using lacquer. Also, in the test of a drying method, a bonding method after drying within a short time at a relatively high temperature was found to be more effective than the drying method after humidifying at a normal temperature, which is used in traditional lacquer ware preservation treatment.
We investigated the morphological characteristics of the pearlescent pigment by using scanning electron microscope, energy dispersive X-ray spectrometry and thermal analyzer. The result is that the shape of pigment is platy polygonal form through observing the pearlescent pigment by the scanning electron microscope. The size of pigment is various and not formed in standardized size or shape. The pigment flakes were measured about from $30{\mu}m$ to $300{\mu}m$. The tip of the piece of pigment is pointed shape or angled. The result of observing them by the scanning electron microscope in magnifying high power is that the edge and the lateral face of them is an round form and the measurement of thickness is about $9{\mu}m$. As well using the high magnification scanning electron microscope, the surface of the pigment flake observed like rugged as coating with the $TiO_2$ element, the diameter of the coating particle is around 60 nm, then the coating particle consists of granular substance. Analysis of the configuration elements of pearlescent pigment using by the energy dispersive X-ray spectrometry is that O, Si, C, Na, Ca, Ti, Zn detected in the surface of pigment and its lateral face identifies similar components. In thermal analysis, there are no contained quantity differences between them in beginning from $100^{\circ}C$ to $800^{\circ}C$ showing thermal analysis, 1.1% out of contained quantity reduced at $115^{\circ}C$, 1.7% dropped at $416^{\circ}C$, and 1.9% decreased at $797^{\circ}C$.
Shoot tips with 2 leaf primordia were cultured to induce shoot primordia in MS liquid medium supplemented with several concentrations of BA and hIAA under the conditions of 10,000 lux illuminations for 24 h and of vertical shaking of 2 rpm in carrot. Two F$_1$ hybrids and two male sterility lines were used. Shoot primordia were only induced in the medium supplemented with 2.0 mg/L of BA and 0.2 mg/L of NAA. Genotypic specificity and seasonal effect of donor parents on shoot primordia induction were not observed and average 15-20% of the planted dornes developed to shoot primordia. The induced shoot primordia were successfully propagated by subculture in the same medium. However, they were grown into three different types during multiplication, that is, the type with multiple small shoots on the surface, the type of without any shoot, and the type of callus. Shoot primordia clusters with small shoots on the surface differentiated multiple shoots successfully in 1/2 MS solid medium supplemented with 0.2 to 1.0 mg/L of IAA and 0.2 to 1.0 mg/L of kinetin. New shoot primordia with small shoots were well formed when pieces bigger than 2 mm in diameter of the out layer of the shoot primordia cluster with small shoots were subcultured. No differences of multiplication and shooting ability and chromosomal variation of shoot primordia were observed until the 13th sub-culture.
This experiment was carried out to establish micropropagation system in Fritillaria thunbergii Miq. Through the culture of bulblet scales, stems, node-buds and shoot tips with special reference to the effect of physiological age of explant and plant growth regulators on bulblet formation. Number of formed bulblets was significantly increased in node-bud or stem tissue compared to scals segments and on the medium supplemented with kinetin than BA containing medium. Optimum levels of kinetin for bulblet formation from node-bud taken from above 3 cm shoot length and stem segments excised from below 3 cm shoot length were 5.0 mg /L and $1.0{\sim}3.0\;mg$ /L kinetin, respectively. Interesting phenomenon was observed, the direct formation of bulblets from the axilliary bud of cultured explants. Bulblet forming capacity in stem tissue was depended on stem age, young stem had high regeneration ability compared to old stem taken from above 10 cm shoot length. 1.0 mg /L kinetin was optimum concentration for the formation of bulblets from old stem segments. Stem tissue taken from underground growing plant was promoted coampare to shoot tips or bulb scale segments. Optimum concentration of sucrose was $5{\sim}7%$. Summariged above results revealed that effective explant for micropropagation was stem and /or node-bud tissue excised from less than 3 cm plant height compared to those of bulb scale segments which showed high contamination after culture. Maximum multiplication rate of young stem and /or node-bud segment was about 20 times. Kinetin requirement for stimulation of bulblet formation from cultured explant depended on source of explants but favorable levels of kinetin for organogenesis ranged from 1.0 mg /L to 5.0 mg /L.
The delamination is a special mode of failure occurring in composite laminates. Several numerical studies with finite element analysis have been carried out on the delamination behavior of unidirectional composite laminates. On the other hand, the fracture for the multi-directional composite laminates may occur not only along the resin-fiber interface between plies known as interply or interlaminar fracture but also within a ply known as interyarn or intralaminar fracture accompanied by matrix cracking and fiber bridging. In addition, interlaminar and intralaminar cracks appear at irregular proportions and intralaminar cracks proceeded at arbitrary angle. The probabilistic analysis method for the prediction of crack growth behavior within a layer is more advantageous than the deterministic analysis method. In this paper, we analyze the crack path when the mode I load is applied to the cross-ply carbon/epoxy composite laminates and collect and analyze the probability data to be used as the basis of the probabilistic analysis in the future. Two criteria for the theoretical analysis of the crack growth direction were proposed by analyzing the stress field at the crack tip of orthotropic materials. Using the proposed method, the crack growth directions of the cross-ply carbon/epoxy laminates were analyzed qualitatively and quantitatively and compared with experimental results.
Background: Lumbar zygapophysial joints are a common source of chronic lower back pain and radiofrequency thermocoagulation (RF) of the medial branches (MB) has been shown to be effective at providing substantial pain relief for chronic low back pain. Therefore, we carried out this study to determine the short term outcomes and prognostic factors of RF on the MB of patients with lumbar facet syndrome. Methods: We performed RF in fourteen patients who showed greater than 80% pain relief up to three times after a diagnostic MB block was conducted using 0.3 ml of 0.5% bupivacaine. Using 10 cm curved electrodes with 10-mm active tip, a 60 second, $80^{\circ}C$ lesion was made after electrical stimulation at 50 Hz for sensory and 2 Hz for motor nerve testing. The degree of pain relief was then assessed after 2 weeks, and again after 3 months using a visual analog scale (VAS) and a four point Likert scale. The outcome was regarded as 'success' if at least a 50% reduction in the VAS was observed. Possible prognostic factors between the two groups were also evaluated Results: The success rate was 71.4% (10/14) after three months of follow-up. However, there were transient complications, such as neuritis like syndrome, in 4 patients. In addition, short symptom duration and low minimal voltage (< 0.4 V) for sensory stimulation were shown to be the relevant prognostic factors for a successful outcome. Conclusions: RF may be an alternative to repeated MB block or intraarticular injection for palliation of lumbar facet syndrome. For better outcomes, early diagnosis and strict patient selection should be coupled with efforts to avoid anatomically incorrect RF.
1. The hair cells on adaxial surface turned out to be penetration way of Gleosporium Thea sinensis in tea plant. 2. The most parts of Gleosporium Thea sinensis generated in tea plant were young leaves with first-fifth leaves from tip of shoot. 3. The proper temperature for spore germination on leaf is $25-27^{\circ}C$, soaked by water for 12 hours. 4. For prevention of Gleosporium Thea sinensis the drug-spay in tea plant would be the most effective when sprayed at this temperature range, and the control of Gleosporium Thea sinensis would be possible through selection of tea plant with few hairs. 5. The treatment of bordeaux mixture to prevent growth of conidiospore was 48.3% more effective than in control plot which were not sprayed. 6. The effect of sprayed bordeaux mixture decreased to about 28.5% after one week of spray.
Chungnam Basin has been known as one of the largest Mesozoic basins in Korea, filled mainly with so-called Daedong Supergroup. The basin has evolved as the Early to Middle Jurassic intra-arc volcano-sedimentary basin developed on top of the Late Triassic to Early Jurassic post-collisional basin in this area, recording evolutionary history of the Mesozoic tectonics in the southwestern Korean Peninsula. This study carries out the geometric interpretations of the Seongjuri syncline and its surroundings in the central part of the Chungnam Basin, based on detailed structural field survey. Based on its doubly-plunging fold geometry, the Seongjuri syncline could be subdivided into the southwestern and northeastern domains. On the down-plunge profiles of the southwestern domain of the Seongjuri syncline as well as the underlying Okma fold, the Okma fault shows typical geometry of a basement-involved reverse fault that propagated up to the sedimentary cover. The profiles illustrate that the Seongjuri syncline occurs in front of the tip of the Okma fault, likely implying its origin as a part of the fault-related fold system. The result of this study will provide better insight into the structural interpretation of the Chungnam Basin, and will further provide useful information for the Mesozoic orgenic events of the southwestern Korean Peninsula.
This study was carried out to clarify the egg, larvae and juveniles development of Carassius cuvieri in Nakdong River, Gyeongbuk. The amount of spawning of female C. cuvieri was about 30,400~44,900 (average 37,650±7,250). The egg shape was circular and the size was 1.24~1.37 mm (average 1.31±0.04 mm, n=30). At 100 hours after fertilization, more than of the total embryos were hatched. The newly hatched larvae had an 4.69~5.65 mm in total length (average 5.15±0.31 mm, n=10) and had egg yolk in the abdomen. At 3 days after hatching, the preflexion larvae absorbed all egg yolk was 6.27~6.70 mm in total length (average 6.59±0.08 mm, n=10). On the 10 days after hatching, the postflexion larvae were 8.71~8.92 mm in total length (average 8.81±0.07 mm, n=10), and the tip of the caudal fin was bent at 45°. On the 42 days after hatching, the total length of 15.1~16.8 mm (average 15.8±0.57 mm, n=10) was transferred to juvenile as the number of fins was (iii17 dorsal fins, iii4 anal fins) reached a constant number of each part.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.