• Transactions of the Society of Information Storage Systems
• /
• v.3 no.2
• /
• pp.94-112
• /
• 2007

Nano-sized inverted domain dots in ferroelectric materials have potential application in ultrahigh-density rewritable data storage systems. Herein, a data storage system is presented based on scanning non-linear dielectric microscopy and a thin film of ferroelectric single-crystal lithium tantalite. Through domain engineering, we succeeded to form an smallest artificial nano-domain single dot of 5.1 nm in diameter and artificial nano-domain dot-array with a memory density of 10.1 Tbit/$inch^2$ and a bit spacing of 8.0 nm, representing the highest memory density for rewritable data storage reported to date. Sub-nanosecond (500psec) domain switching speed also has been achieved. Next, long term retention characteristic of data with inverted domain dots is investigated by conducting heat treatment test. Obtained life time of inverted dot with the radius of 50nm was 16.9 years at $80^{\circ}C$. Finally, actual information storage with low bit error and high memory density was performed. A bit error ratio of less than $1\times10^{-4}$ was achieved at an areal density of 258 Gbit/inch2. Moreover, actual information storage is demonstrated at a density of 1 Tbit/$inch^2$.

• Food Science and Biotechnology
• /
• v.18 no.1
• /
• pp.89-94
• /
• 2009

Frequent outbreaks of foodborne illness have been increasing the awareness of food safety. Conventional methods for pathogen detection and identification are labor-intensive and take days to complete. Some immunological, rapid assays are developed, but these assays still require prolonged enrichment steps. Recently developed biosensors have shown potential for the rapid detection of foodborne pathogens. In this study, an impedimetric biosensor was developed for rapid detection of Salmonella entritidis in food sample. To develop the biosensor, an interdigitated microelectrode (IME) was fabricated by using a semiconductor fabrication process. Anti-Salmonella antibodies were immobilized based on neutravidin-biotin binding on the surface of the IME to form an active sensing layer. To evaluate the effect of electrode gap on sensitivity of the sensor, 3 types of sensors with different electrode gap sizes (2, 5, and $10{\mu}m$) were fabricated and tested. The impedimetric biosensor could detect $10^3\;CFU/mL$ of Salmonella in pork meat extract with an incubation time of 5 min. This method may provide a simple, rapid, and sensitive method to detect foodborne pathogens.

• Geophysics and Geophysical Exploration
• /
• v.7 no.1
• /
• pp.7-13
• /
• 2004

In this paper, we demonstrate that Common Mid-Point (CMP) cross-correlation gathers of multi-channel and multi-shot surface waves give accurate phase-velocity curves, and enable us to reconstruct two-dimensional (2D) velocity structures with high resolution. Data acquisition for CMP cross-correlation analysis is similar to acquisition for a 2D seismic reflection survey. Data processing seems similar to Common Depth-Point (CDP) analysis of 2D seismic reflection survey data, but differs in that the cross-correlation of the original waveform is calculated before making CMP gathers. Data processing in CMP cross-correlation analysis consists of the following four steps: First, cross-correlations are calculated for every pair of traces in each shot gather. Second, correlation traces having a common mid-point are gathered, and those traces that have equal spacing are stacked in the time domain. The resultant cross-correlation gathers resemble shot gathers and are referred to as CMP cross-correlation gathers. Third, a multi-channel analysis is applied to the CMP cross-correlation gathers for calculating phase velocities of surface waves. Finally, a 2D S-wave velocity profile is reconstructed through non-linear least squares inversion. Analyses of waveform data from numerical modelling and field observations indicate that the new method could greatly improve the accuracy and resolution of subsurface S-velocity structure, compared with conventional surface-wave methods.

• Proceedings of the Korea Society for Industrial Systems Conference
• /
• 2002.06a
• /
• pp.76-79
• /
• 2002

Ghost cancelers need to accurately estimate the distortions suffered by transmitted signals on their way to receivers by capturing ghost canceling reference signals in the vertical blanking interval. As ghosts become much severer, sync separation tends to malfunction, making it impossible to acquire measurement data for channel estimation. This paper presents a robust method of acquiring ghost data using their correlation properties, and evaluates its performance through computer simulation. The reference signals are inserted in such a manner that the polarity alternates from one frame to another to remove color bursts and sync signals, and to increase the signal-to-noise ratio as well. As a result, however, they are prone to timing jitters. So a simple yet effective method is proposed that can correct for even fractional time delays. The timing errors are found to be less than about 4% of the sample spacing.

• Journal of Korean Society for Geospatial Information Science
• /
• v.3 no.2 s.6
• /
• pp.199-211
• /
• 1995

Bus, Which is together with subway the main part of public transportation modes in the city, is reviewed for the development of an optimal feeder-bus service area. Based on the IDRISI of GIS package, and taking into account of the convenience of downtown-oriented public transportation users at peak time, a model for the development of feeder-bus service area and a solution and introduced. Major result in this study is as follows: Development is given to a model that is designed to overcome the shortage of the existing models, which has limits in simulating the real situation; Variables were used in combination so that bus and subway route, station spacing, and operating frequency can be determined simultaneously, which enables to elucidate the mutual relationship and the structure in public transportation system. A model for feeder-bus area development is also given applied to determination and opening of subway and urban express bus route and new transportation systems. The model developed in this paper is useful in the case of extension and opening of subway and urban express bus route and new transportation Systems.

• Structural Engineering and Mechanics
• /
• v.53 no.1
• /
• pp.89-104
• /
• 2015

In current bridge management systems (BMSs), load and speed restrictions are applied on unhealthy bridges to keep the structure safe and serviceable for as long as possible. But the question is, whether applying these restrictions will always decrease the internal forces in critical components of the bridge and enhance the safety of the unhealthy bridges. To find the answer, this paper for the first time in literature, looks into the design aspects through studying the changes in demand by capacity ratios of the critical components of a bridge under the train loads. For this purpose, a structural model of a simply supported bridge, whose dynamic behaviour is similar to a group of real railway bridges, is developed. Demand by capacity ratios of the critical components of the bridge are calculated, to identify their sensitivity to increase of speed and magnitude of live load. The outcomes of this study are very significant as they show that, on the contrary to what is expected, by applying restriction on speed, the demand by capacity ratio of components may increase and make the bridge unsafe for carrying live load. Suggestions are made to solve the problem.

• International Journal of Fluid Machinery and Systems
• /
• v.6 no.4
• /
• pp.206-212
• /
• 2013

Self-excited pulse jet is a specific nozzle with a closed chamber which can change a continuous jet into a pulse one. Energy of the pulse jet can be output not only unevenly but also with multifrequency. With the peak pressure of pulse jet, the hitting power would be 2~2.5 times higher than that of continuous jet. In order to reveal the correlation between the self-excited pulse frequency and nozzle diameter ratio, nozzle spacing and operating pressure, the model of 3D unsteady cavitation model has been used. We found that with the same nozzle structure parameters and the different operating pressure, the self-excited frequency and the width of peak crest are different, but the wave profiles are similar. With FFT, we also found that the less bandwidth of amplitude in low frequency range will lead to the wider wave crest of outlet velocity in its time domain, and the larger force of the strike will be gained. By studying the St of self-excite nozzle, not only the frequency of a certain nozzle can be predicted, but also a nozzle structure with a certain frequency can be designed.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.14 no.5
• /
• pp.415-422
• /
• 2009

This paper describes the UIPV(Utility Interactived Photovoltaic) system which can improve the peak-cut effect by adding energy storage device of batteries to the power converter. The proposed system has three possible operation modes depending on relative condition of PV output, which can have the power shaping function covering the peak power for 3 hours. A new power circuit and application algorithm has been applied to UIPV system which is based on working PV system during 3-hour peak time. The energy relationship by the proposed system is analyzed theoretically and experimentally. Also the proposed system is evaluated at the viewpoint of cost and total spacing, which enables the proposed UIPV system to have the reduction of the peak power demand and hence to improve.

• Journal of Korea Foundry Society
• /
• v.13 no.2
• /
• pp.155-162
• /
• 1993

This study has been focused on the influence of the metallic mold cooling effects on the solidification structures and the mechanical properties for Al-10%Si alloy castings by the variation of pouring temperatures, metallic mold temperatures and Cooling part of metallic mold. The dendrite arm spacing of Al-10%Si alloy was decreased with increasing cooling rate. In case of bottom cooling of metallic mold, DAS was appeared to be $20-22{\mu}m$ and in the middle cooling, it was increased to $36-40{\mu}m$. The DAS decreased proportionally $with(cooling\;rate)^{-3/2}$ at pouring temperatures $680^{\circ}C$ and $(cooling\;rate)^{-1/2}$ at pouring temperature $760^{\circ}C$, but it was proportionally increased to $(local\;solidification\;time)^{1/2-1/3}$ at pouring temperature $680^{\circ}C$ and $760^{\circ}C$. The maximum tensile strength of Al-10%Si alloy casting was obtained in case of bottom cooling of mold at pouring temperature $680^{\circ}C$ and metallic mold temperature $320^{\circ}C$.

• Korea journal of population studies
• /
• v.25 no.1
• /
• pp.5-32
• /
• 2002

This research explores the current situation and determinants of induced abortion in Korea. Using 2000 National fertility Survey by Korea Institute of Health and Social Affairs, this study finds that induced abortion rate is rapidly declining so that the role of induced abortion in determining the level of fertility has disappeared. The fundamental reason for resorting to an induced abortion for Korean women is to avoid unwanted birth. Thus, we find that induced abortion is usually taken by Korean women for the purpose of limiting family size and spacing births as in any other countries. Premarital pregnancy and economic hardship are also important reason for taking an induced abortioin, especially for the first time abortion.