• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2005.05a
• /
• pp.173-178
• /
• 2005

The tile construction methods for existing have been used materials within limit which adhesion by wet method in masonry wall and concrete structure. These existing adhesive tech can caused many problems in construction of large and reform tile, after that it can be happened loose scale, peel off, falling off tile by heat and vibration or impact. In according to, this study is to test tile for bond stability, adhesive property by impact, vibration. low property by heat and then, we have the results as below; (1) The tile adhesive stability can be effected as adhesive area between bond agent and tile, adhesive area can more wide and press enough to ensure property. (2) Existing adhesive strength and standard relative tile construction is limited to adjust performance tile on the concrete and masonry wall. In summary, It is necessary to establish standard of performance and test method to ensure tile adhesive salability in dry wall.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2008.11a
• /
• pp.13-16
• /
• 2008

This paper is to present the performance data for improved direct setting method using tile bond for application of porcelain tile under 1 percent absorptance. For this purpose, improved direct setting method type 1 & 2(tile bond curing time 0, 24H) were compared with the conventional setting methods(including direct setting method and improved pressure setting method) in the sight of the adhesive stability of porcelain tile. It tested for tiles after 14, 28days under standard condition and severe conditions. The severe conditions were water immersion, heat ageing(70℃) and freeze-thaw cycle. On the basis of test results, the adhesive strength of direct setting method was lowest for the conventional setting methods. But improved direct setting method using tile bonds(A, B) came close to the result of improved pressure setting method using tile bonds.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2009.05c
• /
• pp.99-102
• /
• 2009

This paper is to present the performance data for pressure setting method using some tile bonds for application on the Ondol-Heating floor system. For this purpose, powder and liquid tile bonds(Organic.Inorganic mixed tile bonds) were compared with the conventional tile cement for pressure setting method in the sight of the adhesive stability of porcelain tile. It tested for tiles after 14, 28days under standard condition and severe conditions. The severe conditions were water immersion and heat ageing($70^{\circ}C$). Another experimental factors concerned tile bond properties such as mixing ratio(in case of using liquid admixture), open time, which are supposed to affect the tensile strength of tile, were studied and discussed through the experiments.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2001.11a
• /
• pp.8-13
• /
• 2001

In recently, polishing tile(porcelain homogeneous polished tile) was used in the construction field as a finishing material. But, there happened some problems such as tile exfoliation by construction condition in early ages. Also, in the dry wall system which used to lightweight wall, for use of polishing tile on dry wall, the examination of adhesive stability of polishing tile is needed. In this Paper, adhesive strength of Polishing tile was investigated by tile bond types on gypsum board and non asbestos board coated by tar-urethane and polymer modified cementitious waterproofing membrane(Series I). Then, the effect of heat stress and vibration was estimated on gypsum and non asbestos board(Series II).

• Journal of the Korea Institute of Building Construction
• /
• v.2 no.3
• /
• pp.163-170
• /
• 2002

Recently, polishing tile(porcelain homogeneous polished tile) was used in the construction field as a finishing material. But, there happened some problems such as tile exfoliation by construction condition in early ages. Also, for use of polishing tile in the dry wall system which used to lightweight wall, the examination of adhesive stability of polishing tile is needed. In this study, adhesive strength of Polishing tile was investigated by tile bond types on gypsum board and non asbestos board coated by tar-urethane and Polymer modified cementitious waterproofing membrane(Series I). Then, the effect of heat stress and vibration was estimated on gypsum and non asbestos board(Series II). As the result of study are the follows; (1) Polishing tile(600$\times$400mm) construction on waterproofing layer : Both laboratory estimation and spot examination sieve were happened that fall of tile because their hardening speed is late. (2) To using powder style adhesives in the dry wail with waterproofing layer : Adhesive strength of tile is Influenced by interface bond area and base side condition. (3) Shock and heat stresses : obvious decline of adhesive strength is not happened

• Journal of the Korean Society of Safety
• /
• v.4 no.1
• /
• pp.91-98
• /
• 1989

Today, the conception of building architecture is changing the conception that it is a kind of product and the operator of construction try to produce excellent building through developing efficiency and materials of building component. This study improves the problematic point of the extenor tile setting, through making on experiment on the method of it and purposes doing to do the exterior tile setting of good quality as it selects out of the most conformable the method. The experimental materials choose the tile of 60$\times$108mm size which are using frequently in the exterior tile setting and mortar is made from sand of Han river and potland cement, which apply the volume mixing of the ratio 1：3. The water cement ratio (W/C)is made up 62％ The methods of tile setting utilise the method of the tile setting and laying the method of the tile improved setting and laying, the method ol the pressing adhesion, the method of the improved pressing adhesion and the method of setting adherent (the method of VIBRATOR).

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2018.05a
• /
• pp.283-284
• /
• 2018

The rear side surface of tiles act have protrusions that helps secure the adhesion between the tile and the mortar for tile setting. Conventional height of the rear side usually ranges between 1 to 1.5 mm, and the molding method is classified in between press type and compression type during the manufacturing process, with most tiles being produced by the former method. In sites where adhesion failures were observed, tiles were taken to examine the cause of defect. It was determined that height was irregular at the rear side surface. Based on these findings, an experiment was conducted to determine the correlation between the rear surface and the bonding strength of tiles.

• Journal of the Korea Institute of Building Construction
• /
• v.1 no.2
• /
• pp.185-190
• /
• 2001

The purpose of this study is the development of practical Dry floor tile unit method that settle the defect of a wet method and designed for resin mat. With use of PE resin which is confirmed the basic property, it is developed that resin mat, joint-sealing compound with fixed form and space management to Dry floor tile unit method. The result of this study is below. 1) To acquire above the 4kgf/$\textrm{cm}^2$ - construction specification criterion, the bonding space that between resin mat and tile has to occupy the 50% of resin mat module space(10,000$\textrm{cm}^2$). 2) Criteria of bonding part plane is below. simpleness of metal form. productivity, uniform quality after injection molding cooling, easy cutting for remain space management, adhesive property, construction ability, transformation of a severed piece under pressure and so on. 3) To get the shape that could protect the interfacial breakdown, it is designed that resin mat and tile are unified after the bond input. 4) Adapted joint-sealing compound is the material of urethane kinds wedge form. Resin mat has the water passageway that could drain the water. 5) To manage the severed piece of tile, the resin mat is likely to divide the half and the quarter and the plastic drainage is developed in the severed piece.

• The Journal of Korean Academy of Prosthodontics
• /
• v.25 no.1
• /
• pp.303-316
• /
• 1987

The purpose f this study was to evaluate the effect of resin film thickness on the tensile bond strength and to compare the tensile bond strengths of 4 differently treated metal surfaces. For the experiment, seventy metal specimens were cast with Verabond and divided into I, II, III, groups. The metal specimens in group I were electrolytically etched and cemented with Panavia under finger pressure. Cement film thickness was regulated with metal spacers. The metal specimens in Group II were treated by 4 methods, such as electrolytic etching method, salt-roughened method, EZ-oxisor method , chemical etching method and cemented with Panavia. In group III, electrolytically etched metal specimens were cemented with Hy-Bond. The etched surface of metal specimens and the cement film thickness were examined under the scanning electron microscope. Results were as follows; 1. The tensile bond strength showed no significant difference between $30{\mu}m,\;80{\mu}m,\;130{\mu}m$ film thicknessspecimens. 2. There was no significant difference in the tensile bond strength between the 4 differently treated metal specimens. 3. The tensile bond strength showed significant difference between Panavia and Hy-Bond. 4. Scanning electron microscope photograph revealed that tile interdendritic eutectic was removed in electrolytically etched metal surfaces hilt even dendritic arm was removed in Chemically etched metal surfaces. 5. The metal surfaces which were air-abraded with $50{\mu}m$ aluminum oxide showed roughness and small crack on scanning electron microscope photograph.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2002.10a
• /
• pp.829-834
• /
• 2002

Recently, research and development for a number of repairing material like an epoxy-based material and polymer-cementitious material as well as anti-washout underwater concrete have been carried out. But, the study on tile materials for the concrete structure exposed to a wetted condition is at a standstill and there are not any suitable reference data at a repairing work for the concrete structure at a splash as well as a structure under severe moisture condition. In this study, the material, called as “ceramic metal”, with an excellent mobility and plasticity as well as with a high bond strength and durability of freezing-thawing resistant properties under any environmental conditions was developed. And, the experimental evaluations for the utility wert widely performed.