• Corrosion Science and Technology
• /
• v.15 no.3
• /
• pp.129-134
• /
• 2016

The effects of Ti on the high temperature oxidation of Ni-based superalloys were investigated by cyclic oxidation at $850^{\circ}C$ and $1000^{\circ}C$. The oxide scale formed at $850^{\circ}C$ consists of $Cr_2O_3$, $Al_2O_3$, and $NiCr_2O_4$ layers, while a continuous $Al_2O_3$ layer was formed at $1000^{\circ}C$. The oxidation rate of the alloy with higher Ti content was higher than the alloy with less Ti content at $850^{\circ}C$, possibly due to the increase in the metal vacancy concentration in the $Cr_2O_3$ layer involved by incorporation of $Ti^{4+}$. However, Ti improved the oxidation resistance of the superalloy at $1000^{\circ}C$ by reducing oxygen vacancy concentration in $Al_2O_3$ layer.

• Journal of the Korean institute of surface engineering
• /
• v.38 no.3
• /
• pp.106-111
• /
• 2005

Ternary Ti-B-C coatings were synthesized on WC-Co and Si wafers substrates by a PECVD technique using a gaseous mixture of $TiCl_4,\;BCl_3,\;CH_4,\;Ar,\;and\; H_2$. The effects of deposition variables such as substrate temperature, gas ratio, $R_x=[BCl_3/(CH_4+BCl_3)]$ on the microstructure and mechanical properties of Ti-B-C coatings were investigated. From our instrumental analyses, the synthesized Ti-B-C coatings was confirmed to be composites consisting of nanocrystallites TiC, quasi-amorphous TiB2, and amorphous carbon at low boron content, on the contrary, nanocrystallites $TiB_2$, quasi-amorphous TiC, and amorphous carbon at relatively high boron content. The microhardness of the Ti-B-C coatings increased from $\~23 GPa$ of TiC to $\~38 GPa$ of $Ti_{0.33}B_{0.55}C_{0.11}$ coatings with increasing the boron content. The $Ti_{0.33}B_{0.55}C_{0.11}$ coatings showed lower average friction coefficient of 0.45, in addition, it showed relatively better wear behavior compared to other binary coatings of $TiB_2$ and TiC. The microstruture and microhardness value of Ti-B-C coatings were largely depend on the deposition temperature.

• Proceedings of the KIEE Conference
• /
• 1996.07c
• /
• pp.1434-1436
• /
• 1996

In this study, ferroelectric $PbTiO_3$ thin films were deposited on the Pt/$SiO_2$/Si substrate by Sol-Gel method. $PbTiO_3$ stock solution was made and spin-cooled at 4000[rpm] for 30[sec.]. Coated specimens were dried at $400[^{\circ}C]$ for 10[min.] and then annealed at $500{\sim}800[^{\circ}C]$ for 1 hour. Annealing temperature were examined to optimize micro structural and dielectric properties of the films. The ferroelectric perovskite phase was observed in the file annealed at $700[^{\circ}C]$ for 1 hour. In the case of $PbTiO_3$ thin films annealed at $700[^{\circ}C]$ for hour, dielectric constant and dielectric loss showed the good value of 324, 2.0[%], respectively.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2000.02a
• /
• pp.123-123
• /
• 2000

선폭이 초미세화됨에 따라 게이트 전극에서의 공핍 현상 및 불순물 확산의 물제를 갖는 poly-Si 게이트를 대체할 전극 물질로 텅스텐(W)이 많이 연구되어 왔다. 반도체 소자의 배선물질로 일찍부터 사용되어온 텅스텐은 내화성 금속의 일종으로 용융점이 높고, 저항이 낮다. 그러나, 일반적으로 사용되고 있는 CVD에 의한 텅스텐의 증착은 반응가스(WF6)로부터 오는 불소(F)의 게이트 산화막내로의 확산으로 인해 MOS 소자가 크게 열화될수 있다. 본 연구에서는 W/TiN 이중 게이트 전극 구조를 갖는 MOS 캐패시터를 제작하여 전기적 특성을 살펴보았다. P-Type (100) Si위에 RTP를 이용, 85$0^{\circ}C$에서 110 의 열산화막을 성장 및 POA를 수행한 후, 반응성 스퍼터링법에 의해 상온, 6mTorr, N2/Ar=1/6 sccm, 100W 조건에서 TiN 박막을 150, 300, 500 의 3그룹으로 증착하였다. 그 위에 LPCVD 방법으로 35$0^{\circ}C$, 0.7Torr, WF6/SiH4/H2=5/5~10/500sccm 조건에서 2000~3000 의 텅스텐을 증착하였다. Photolithography 공정 및 습식 에칭을 통해 200$\mu\textrm{m}$$\times$200$\mu\textrm{m}$ 크기의 W/TiN 복층 게이트 MOSC를 제작하였다. W/TiN 복측 게이트 소자와 비교분석하기 위해 같은 조건의 산화막을 이용한 알루미늄(Al) 게이트, 텅스텐 게이트 MOSC를 제작하였다. 35$0^{\circ}C$에서 증착된 텅스텐 박막은 10~11$\Omega$/ 의 면저항을 가졌고 미소한 W(110) peak값을 나타내는 것으로 보아 비정질 상태에 가까웠다. TiN 박막의 경우 120~130$\Omega$/ 의 면저항을 가졌고 TiN (200)의 peak 값이 크게 나타난 반면, TiN(111) peak가 미소하게 나타났다. TiN 박막의 두께와 WF/SiH4의 가스비를 변화시켜가며 제작된 MOS 캐패시터를 HF 및 QS C-V, I-V 그리고 FNT를 통한 전자주입 방법을 이용하여 TiN 박막의 불소에 대한 확산 방지막 역할을 살펴 보았다. W/TiN 게이트 MOS 소자는 모두 순수 텅스텐 게이트보다 우수하였고, Al 게이트와 유사한 전기적 특성을 보여주었다. W/TiN 게이트 MOS 소자는 모두 순수 텅스텐 게이트보다 우수하였고, Al 게이트와 유사한 전기적 특성을 보여주었다. TiN 박막이 300 , 500 이고 WF6/SiH4의 가스비가 5:10인 경우 소자 특성이 우수하였으나, 5:5의 경우에는 FNT 전자주입 특성이 열화되기 시작하였다. 그리고, TiN박막의 두께가 150 으로 얇아질 경우에는 WF6/SiH4의 가스비가 5:10인 경우에서도 소자 특성이 열화되기 시작하였다. W/TiN 복층 게이트 MOS 캐패시터를 제작하여 전기적인 특성 분석결과, 순수 텅스텐 게이트 소자의 큰 저전계 누설 전류 특성을 해결할 수 있었으며, 불소확산에 영향을 주는 조건이 WF6/SiH4의 가스비에 크게 의존됨을 알 수 있었다. TiN 박막의 증착 공정이 최적화 될 경우, 0.1$\mu\textrm{m}$이하의 초미세소자용 게이트 전극으로서 텅스텐의 사용이 가능할 것으로 보여진다.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.5 no.3
• /
• pp.240-249
• /
• 1995

Rutile type of $TiO_{2}$ single crystal was grown by floating zone method in order to obtain the highly transparent and contamination-free single crystal. The linear refractive index of perpendicular and parallel to c-axis was measured as a function o f wavelength from 500 to 1000nm. The optical energy band gap was estimated as 2.99 eV from the absorption spectrum. The theoretical $\chi^{(3)}$} value of $TiO_{2}$ was discussed in comparison with that of $SiO_{2}$ quartz single crystal on the basis of semiempirical model. On the other hand, the second-hyperpolarizability, ${\gamma}({Ti}^{4+})$ was calculated in order to describe the effect of $Ti_{4}$ ion on the third order nonlinear optical properties.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.33 no.7
• /
• pp.652-657
• /
• 2009

Strength characteristics of $Si_3N_4$ composite ceramics has been studied as functions of heat-treatment temperature and additive $SiO_2$. $SiO_2$ colloidal could significantly increase the bending strength. Crack healing temperature decreased 300 K by additive $TiO_2$. Bending strength of specimen added $SiO_2$ is higher than that of non-added $SiO_2$. Moreover, bending strength of specimen with $SiO_2$ colloidal coating is much higher that of non-coated specimen. In in-situ observation, crack-healed specimen at 1,573 K shows phenomenon like a fog on the surface. By SPM, both crack-healed specimen, non-coating and coating of $SiO_2$ colloidal, at 1,273 K were healed completely but both of 1,573 K exist crack. This was made by evaporation of $SiO_2$ at high temperature. Crack-healing materials of $Si_3N_4$ composite ceramics is crystallized $Y_2Si_2O_7$, $Y_2Ti_2O_7$ and $SiO_2$. A large amount of Si and O, and little C were detected by EPMA. Si and O increase but C decreases according to heat treatment temperature. Specimens with additive $SiO_2$ were more detected Si and O than that of non-additive $SiO_2$. Specimen with $SiO_2$ colloidal coatings were much more detected O.

• Korean Journal of Materials Research
• /
• v.5 no.2
• /
• pp.169-177
• /
• 1995

The diffusion barrier property of 100-nm-thick titanium nitride (TiN) film between Cu and Si was investigated using sheet resistance measurements, etch-pit observation, x-ray diffractometry, Auger electron spectroscopy, and transmission electron microscopy. The TiN barrier fails due to the formation of crystalline defects (dislocations) and precipitates (presumably Cu-silicides) in the Si substrate which result from the predominant in-diffusion of Cu through the TiN layer. In contrast with the case of Al, it is identified that the TiN barrier fails only the in-diffusion of Cu because there is no indication of Si pits in the Si substrate. In addition, it appears that the stuffing of TiN does not improve the diffusion barrier property in the Cu/TiN/Si structure. This indicates that in the case of Al, the chemical effect that impedes the diffusion of Al by the reaction of Al with $TiO_{2}$ which is present in the grain boundaries of TIN is very improtant. On the while, in the case of Cu, there is no chemical effect because Cu oxides, such as $Cu_{2}O$ or CuO, is thermodynamically unstable in comparison with $TiO_{2}$. For this reason, it is considered that the effect of stuffing of TiN on the diffusion barrier property is not significant in the Cu/ TiN/Si structure.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07b
• /
• pp.861-864
• /
• 2002

Ferroelectric $Bi_{4-x}Nd_xTi_3O_{12}$(BNdT) thin films with the composition(x=0.75) were prepared on pt/Ti/$SiO_2$/Si(100) substrate by metal-organic deposition. The electrical and structural characteristics of BNdT thin films were investigated to develop ferroelectric thin films for capacitor layers of FRAM. After spin coating, thin films were annealed at $650^{\circ}C$ for 1hour in oxygen atmosphere. Scanning electron micrographs showed uniform surfaces composed of rod-like grains. The $Bi_{4-x}Nd_xTi_3O_{12}$(X=0.75) thin film capacitors with a Pt top electrode showed better ferroelectric properties. At the applied voltage of 5V, the dielectric constant$(\varepsilon_r)$, dissipation factor$(tan{\delta})$, remanent polarization(2Pr) and nonvolatile swiching charge of the $Bi_{4-x}Nd_xTi_3O_{12}$(x=0.75)thin films were about 346.7, 0.095, $56{\mu}C/cm^2$ and $38{\mu}C/cm^2$ respectively. Also the capacitor did not show any significant fatigue up to $8{\times}10^{10}$ read/write switching cycles at a frequency of 1MHz.

• Korean Journal of Materials Research
• /
• v.7 no.8
• /
• pp.635-639
• /
• 1997

ECR-PECVD법을 사용하여 450-49$0^{\circ}C$이하의 온도에서 Pt/SiO$_{2}$/Si기판 위에 PZT 박막을 증착하였다. 기판 온도가 46$0^{\circ}C$ 이하일 경우에는 페로브스이트 상과 제2상으로 이루어진 박막이 성장하였으며 기판온도가 47$0^{\circ}C$이상일 때에는 페로브스카이트 단일상의 PZT 박막이 성장하였다. 49$0^{\circ}C$에서 매우 얇은 페로브스카이트의 PZT 박막을 증착한 후 $650^{\circ}C$에서 1분간 raped thermal annealing(RTA) 처리한 결과 박막의 조성과 결정성에는 거의 변화가 없었으나 박막의 전하 저장 밀도는 크게 향상되었다. 이는 RTA 처리에 의한 저유전 계면층의 소멸이 주된 이유라고 판단된다. 열처리 후 두께 40-45nm의 PZT박막은 200kV/cm의 전장 하에서 $10^{-6}$$\textrm{cm}^2$이하의 누설전류값을 갖고 있었으며, 인가전압 1V에서 300fF/$\mu$$m^2$의 정전용량, 즉 SiO$_{2}$환산두께 0.12nm를 나타내었다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.05a
• /
• pp.649-652
• /
• 1999

The (Ba, Sr)TiO$_3$(BST) thin films were fabricated on Pt/Ti/SiO$_2$/Si substrate by RF sputtering technique. The structural properties of the BST thin films were investigated with substrate temperature by XRD, SEM, EDS and AES depth profils. Increasing the substrate temperature, barium multi titanate phases were decreased. The BST thin film had a structure of perovskite type, and had peaks of (100), (200) at the substrate temperature of 50$0^{\circ}C$. When the BST thin films were deposited at the substrate temperature of 50$0^{\circ}C$, the composition ratio of Ba/sr was 52/48.