• Journal of the Korean Solar Energy Society
• /
• v.26 no.2
• /
• pp.1-7
• /
• 2006

A numerical investigation was performed to determine the effect of airfoil on the optimum flap height using NACA0015 Wells turbine. The five double flaps which have 0.5% difference were selected. A Navier-Stokes code, CFX-TASCflow, was used to calculate the flow field of the Wells turbine. The basic feature of the Wells turbine is that even though the cyclic airflow produces oscillating axial forces on the airfoil blades, the tangential force on the rotor is always in the same direction. Geometry used to define the three dimension numerical grid is based upon that of an experimental test rig. This paper tries to disign the double flap of Wells turbine with the numerical analysis.

• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.2857-2861
• /
• 2007

Flow and aerodynamic characteristics were analyzed numerically for a commercial passenger airplane, Boeing 747-400, flying in the cruising condition. The model geometry with 100:1 in scale was obtained by the photo scanning measurement with the maximum error of 1.4% comparing with the real airplane dimension. The three-dimensional inviscid steady compressible governing equations were solved by the finite volume method in the unstructured grid system. The convective terms were treated by the Crank-Nicholson and first-order upwind schemes. In the computational results, the strong wing-tip vortices were clearly observed and the pressure contours on the airplane surface were suggested. The lift and drag forces in the wing with engines increase by 1.49% and 3.9%, respectively compared with the case without engines. The aerodynamic forces were estimated quantitatively for each element which consists of the airplane.

• Journal of the Korean Institute of Educational Facilities
• /
• v.14 no.4
• /
• pp.14-24
• /
• 2007

Recently, there are three major trends in building school facilities by government. First trend is to reconstruct facilities that have been built for 30 years. Second is the creation of a new town, new construction demanded from the redeveloping area. Finally, third is to build educational convenience facilities such as gymnasium, auditorium and cafeteria etc. When building or reconstructing school facilities, it is important to consider the 7th Education curriculum. The purpose of this study is to propose the guide line of the planning the dimension of Science Laboratory in in elementary school, corresponding to teaming contents and method.

• Geotechnical Engineering
• /
• v.8 no.1
• /
• pp.7-18
• /
• 1992

This paper is a basic study of three by finite element method. Plate and medium. Plate is discretized 4 node p melt. At the interface between plate a melt is adopted for considering plate Measured vertical displacement out by plate foundation interaction finite zion is followed as ; 1. as being interface element adopts dation interaction finite element 2. As being interface element and platefoundation interaction finite 3. As being interface element adopte Therefore, post processing that as.

• Journal of the Korea Safety Management & Science
• /
• v.6 no.1
• /
• pp.187-199
• /
• 2004

To suggest a more efficient way of delivering information for process control under computerized environment, population stereotypes of colors were tested with 57 Korean subjects. The subjects were asked to associate 11 colors salient at electronic video displays with 55 pairs of adjectives that might be used when they explain the current state of process. The levels of association were evaluated with semantic differential methods by 7 point scales. Based on the multivariate analyses, the 55 pairs of adjectives were grouped into three distinct dimensions. The emotional maps of the 11 colors with respect to each dimension were presented. The Quantitative relationships between the colors and subjective impressions were also calculated by quantification theory I. On the basis of these color associations, it was suggested a general guideline for color coding when delivering process information

• Journal of Advanced Marine Engineering and Technology
• /
• v.35 no.7
• /
• pp.907-913
• /
• 2011

Swirling flows are related to the spiral motion in the tangential direction in addition to the axial and radial direction using several swirl generators. These type of flows are used in combustion chambers to improve flame stability, heat exchanger to enhance heat transfer coefficients, agricultural spraying machines and some vertical pipes to move slurries or transport of materials. However, only a few studies three dimensional velocity profiles in a vertical pipe have been reported. In this present paper, 3 dimension particle image velocimetry(PIV) technique was employed to measure the velocity profiles in water along a vertical circular pipe with Reynolds number from 6000 to 13,000. A tangential inlet condition was used as the swirl generator to produce the required flow. The velocities were measured with swirling flow in the water along the test section using the PIV technique.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2000.04b
• /
• pp.119-124
• /
• 2000

The radar method is becoming one of the major nondestructive testing (NDT) techniques for concrete structures. Numerical modeling of electromagnetic wave is needed to analyze radar measurement results and to study the influence of measurement parameters on the radar measurements. Finite difference-time domain (FD-TD) method is used to simulate electromagnetic wave propagation through concrete specimens. Three concrete specimens with a 25 mm delamination embedded at 25 mm, 50 mm, and 75mm depth are modeled in 3-dimension. Also, thickness change of delamination and permittivity change are modeled.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2000.04b
• /
• pp.222-229
• /
• 2000

Malty bridges are severely damaged by the overloaded heavy vehicle and tile trend will become more serious because the traffic volume is continuously increasing. Currently, the vehicles with gross weights over 40 tons or axle weight over 10 tons are not allowed on the public road. However, this regulation is not based on a systemetic study on the bridge capacityand assumed to be much too conservative depending on the vehicle types ans bridge types. In this study, the permit weights of heavy vehicles of diverse axle spacings and axle load distribution are calculated considering the structural characteristics of bridge superstructures. In order to consider the various load effects of heavy weight vehicle crossings, three conditions are considered in the calculation of permit vehicle load. From the results, the permit vehicle weights of bridges are calculated and simplified formulas which can be used in the case when only the vehicle dimension are known are presented.

• Journal of Industrial Technology
• /
• v.21 no.B
• /
• pp.51-58
• /
• 2001

The Distinct Element Method (DEM) was used to analyze the stability of jointed rock slope, of which dimension are about 200m(length), 60m(height), $55^{\circ}$ dip. The Barton-Bandis joint model was used, as a constitutive model. The parameters such as JRC and spatial distribution characteristics of discontinuities were acquired through field investigation. Three different cases such as $51^{\circ}$, $45^{\circ}$ and $38^{\circ}$ in angle of rock slope were analyzed to decide a stable slope. To keep the jointed rock slope safely, it is proposed to reduce the height of slope from 60m to 48m and to reduce the angle of the from $55^{\circ}$ to $38^{\circ}$ too.

• Journal of Magnetics
• /
• v.19 no.1
• /
• pp.72-77
• /
• 2014

This paper proposes an indirect fault detection method for an onboard degaussing coil system, installed to reduce the underwater magnetic field from the ferromagnetic hull. The method utilizes underwater field signals measured at specific magnetic treatment facilities instead of using time-consuming numerical field solutions in a three-dimensional space. An equivalent magnetic charge model combined with a material sensitivity formula is adopted to predict fault coil locations. The purpose of the proposed method is to yield reliable data on the location and type of a coil breakdown even without information on individual degaussing coils, such as dimension, location and number of turns. Under several fault conditions, the method is tested with a model ship equipped with 20 degaussing coils.