• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2011년도 춘계학술대회 초록집
• /
• pp.130.2-130.2
• /
• 2011

본 연구에서는 RF magnetron sputtering을 이용하여 실리콘 박막 태양전지용 ZnO:Al 전면전극을 제작하고 다양한 식각조건에 따른 ZnO:Al 박막의 표면형상 변화와 함께 전기적 및 광학적 특성 변화를 조사하였다. pin 구조를 갖는 실리콘 박막 태양전지의 효율 향상을 위해서는 입사광의 산란효과에 따른 광포획 증가가 필수적이며 이를 위하여 ZnO:Al 전면전극의 표면텍스처링 형성이 필요하다. 식각용액으로는 HCl과 HF 등을 사용하였으며 식각용액 농도 및 식각시간을 변화시켰다. 식각 후의 ZnO:Al 박막의 표면형상은 SEM(Scanning Electron Microscope)과 AFM(Atomic Force Microscope)을 이용하여 분석을 하였고, UV-visible-nIR spectrometer를 이용하여 총 투과도 및 산란 투과도를 측정하였다. 이 외에도 four-point probe 및 Hall measurement를 이용하여 전기적 특성 변화를 조사하였다. 다양한 식각조건에 따라 제조된 ZnO:Al 박막 위에 실리콘 박막 태양전지를 제작하여 전면전극의 표면형상에 따른 태양전지 성능변화를 비교 분석하였다.

• 신재생에너지
• /
• 제1권2호
• /
• pp.6-10
• /
• 2005

[ $CulnSe2$ ]계 화합물은 직접천이형 반도체로 광흡수계수가 매우 높아 박막형 태양전지 제조에 매우 유리하다. 또한 화학적으로 안정하며 Ga, Al 등을 첨가하면 에너지 금지대폭을 조절할 수 있어 Wide Bandgap 태양전지 및 탠덤구조 태양전지를 제조하기에도 용이하다. CIS 물질에서 In을 $20-30\%$ 정도 치환한 $Cu(In,\;Ga)Se_2(CIGS)$ 태양전지의 경우 19.5%의 세계 최고 효율을 보고하고 있으며 이는 다결정 실리콘 태양전지의 효율과 비슷한 수준이다. 본 연구에서는 동시 질공증발법을 이용하여 증착한 CIGS 박막 및 $CuGaSe_2(CGS)$ 박막을 이용하여 태양전지를 제조하였다. 공정의 재현성 및 결정립계가 큰 광흡수층 제조를 위하여 실시간 기판 온도 모니터링 시스템을 도입하였으며 버퍼층으로는 용액성장한 CdS 박막을 사용하였다. SLG/MO/CIGS(CGS)/CdS/ZnO/Al 구조의 태양전지를 제조하여 면적 $0.5cm^2$에서 각각 $17\%(CIGS)$와 $7\%(CGS)$의 효율을 얻었다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제45회 하계 정기학술대회 초록집
• /
• pp.193-193
• /
• 2013

실리콘 박막 태양전지는 광 흡수층에서 형성된 정공과 전자를 효과적으로 분리하기 위해 p형과 n형으로 도핑된 층을 형성하는 p-i-n구조를 갖게 된다. 이러한 도핑 층을 형성하기 위해 B2H6와 PH3와 같은 독성 가스를 사용하기 때문에, 공정 안정성과 환경적인 이슈가 대두된다. 또한 도핑은 추가적으로 실리콘 박막 태양전지의 안정화 효율을 지속적으로 저하시키는 요인이 된다. 이러한 문제점을 개선하기 위하여, 창층으로 MoO3, V2O5, WO3 등과 같이 높은 일함수를 갖는 전이금속 산화물을 사용하고, 광 흡수층으로 i-Si:H을, 후면 전극으로 낮은 일함수를 나타내는 LiF/Al을 사용하였다. 전이금속 산화물과 LiF/Al의 큰 일함수 차이에 의해서 흡수층인 i-Si:H 에서 생성된 캐리어들은 효과적으로 분리되고 수집이 된다. 금속 산화물은 스퍼터링 공정에 의하여 이루어졌으며, 스퍼터링 공정조건에 따라 산화도가 조절되며, 이러한 산화도에 따라 태양전지의 셀 특성이 결정된다. 도핑 층이 없는 새로운 형태의 실리콘 박막 태양전지는 기존 비정질 실리콘 박막 태양전지에 비해 높은 안정화 효율을 나타내며, 이는 도핑 층이 없기 때문에 기존 실리콘 박막 태양전지의 열화현상에 따른 효율저하가 발생하지 않는 장점을 지내고 있다.

• 한국전기전자재료학회논문지
• /
• 제36권1호
• /
• pp.49-55
• /
• 2023

The deposition of indium zinc oxide (IZO) thin films was carried out on substrate at room temperature by RF magnetron sputtering. The effects of substrate temperature, RF power and deposition pressure were investigated with respect to physical and optical properties of films such as deposition rate, electrical properties, structure, and transmittance. As the RF power increases, the resistivity gradually decreases, and the transmittance slightly decreases. For the variation of deposition pressure, the resistivity greatly increases, and the transmittance is decreased with increasing deposition pressure. As a result, it was demonstrated that an IZO film with the resistivity of 3.89 × 10^-4 Ω∙cm, the hole mobility of 51.28 cm²/Vs, and the light transmittance of 86.89% in the visible spectrum at room temperature can be prepared without post-deposition annealing.

• Current Photovoltaic Research
• /
• 제11권3호
• /
• pp.67-74
• /
• 2023

The earth-abundant element-based Cu₂ZnSn(S,Se)₄ (CZTSSe) thin film solar cells (TFSCs) have attracted greater attention in the photovoltaic (PV) community due to their rapid development in device power conversion efficiency (PCE) >13%. In the present work, we demonstrated the fine-tuning of the bandgap in the CZTSSe TFSCs by altering the sulfur (S) to the selenium (Se) chalcogenide ratio. To achieve this, the CZTSSe absorber layers are fabricated with different S/(S+Se) ratios from 0.02 to 0.08 of their weight percentage. Further compositional, morphological, and optoelectronic properties are studied using various characterization techniques. It is observed that the change in the S/(S+Se) ratios has minimal impact on the overall Cu/(Zn+Sn) composition ratio. In contrast, the S and Se content within the CZTSSe absorber layer gets altered with a change in the S/(S+Se) ratio. It also influences the overall absorber quality and gets worse at higher S/(S+Se). Furthermore, the device performance evaluated for similar CZTSSe TFSCs showed a linear increase and decrease in the open circuit voltage (V_oc) and short circuit current density (J_sc) of the device with an increasing S/(S+Se) ratio. The external quantum efficiency (EQE) measured also exhibited a linear blue shift in absorption edge, increasing the bandgap from 1.056 eV to 1.228 eV, respectively.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.426.1-426.1
• /
• 2014

For high performance thin film solar cells, texturing surface, enhancing the optical absorptionpath, is pretty important. Textured ZnO:Al transparent oxide layer of high haze is commonly used in Si thin film solar cells. In this paper, novel deposition method for aluminum doped zinc oxide (ZnO:Al) on glass substrates is presented to improve the haze property. The broccoli structure of ZnO:Al layer was formed on chemically etched glass substrates, which showed high haze value on a wide wavelength range.The etching condition of the glass substrates can change not only the haze values of the ZnO:Al of in-situ growth but alsothe electrical and optical properties of the deposited ZnO:Al films.The etching mechanism of the glass substrate affecting on the surface morphology of the glass will be discussed, which resulted in variation of texture of ZnO:Al layer. The optical properties of substrate morphology were also analyzed with EDS and FTIR results. As a result, the high haze value of 85.4% was obtained in the wavelength range of 300 nm to 1100 nm. Furthermore, low sheet resistance of about 5~18 ohm/sq was achieved for different surface morphologies of the ZnO:Al films.

• 한국재료학회지
• /
• 제16권7호
• /
• pp.449-454
• /
• 2006

Al-doped zinc oxide (ZnO:Al) films for transparent electrodes in thin film solar cells were deposited on glass substrates at a low temperature of $200^{\circ}C$ by rf magnetron sputtering. The transmittance of the ZnO:Al films in the visible range was 87%. The lowest resistivity of the ZnO:Al films was about $5.8{\times}10^{-4}{\Omega}$ cm at the Al content of 2.5 wt%. After deposition, the surface of ZnO:Al films were etched in dilute HCl (0.5%) for the investigation of the change in the electrical properties and the surface morphology due to etching.

• 대한전기학회논문지
• /
• 제37권2호
• /
• pp.96-101
• /
• 1988

This work is concerned with the fabrication process and photo-response characteristics of Cd S/(p) Si solar cells. In order to fabricate the cell. low grade Si wafer has been used as an absorber and Cd S which works as a window material has been prepared by vacuum evaporation. Cd S thin film, as evaporated, is polycristal and resistance is very high but these properties are improved by annealing. The properties of the fabricated cells are found to depend largely on the transmittance of Cd S. The effects of Cd S thickness and annealing condition on the fill factor and efficiency of the cell are investigated quantitatively.

• 한국전기전자재료학회논문지
• /
• 제21권9호
• /
• pp.789-794
• /
• 2008

Zinc oxide (ZnO) has been widely studied for its practical applications such as transparent conduction electrodes for flat panel displays and solar cells. Especially, ZnO films show good chemical stability against hydrogen plasma, absence of toxicity, abundance in nature, and then suitable for photovoltaic applications. However, the fabrication process of thin film solar cells require a high substrate temperature and/or post heat treatment. Therefore, the layers have to withstand high temperatures, requiring an excellent stability without degrading their electronic and optical properties. In this paper, we investigated the stability of zinc oxide (ZnO) films doped with aluminum and hydrogen. Doped ZnO films were prepared by r.f. magnetron sputter and followed by heat treatment at different temperatures and for various times.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 D
• /
• pp.1729-1731
• /
• 1999

The effect of Na on the structural and electrical properties of CIGS films were studied and their effects on the CIGS/Mo thin film solar cells were investigated. Soda-lime glass and Corning glass were used as substrates to compare the effect of Na diffusion into CIGS film. The resistivity of CIGS films was not changed in the Cu-poor region due to diffusion of Na from soda-lime glass but was mainly determined by the surface resitivity controlled by excess Na.