• 마이크로전자및패키징학회지
• /
• 제11권1호
• /
• pp.37-42
• /
• 2004

최근에 3 ㎓이상의 고주파용 전자부품과 소자의 제조에 낮은 저항온도계수(TCR)값과 높은 정밀도를 갖는 박막저항이 사용되고 있다. Ni-Cr 박막저항은 낮은 TCR 값과 저항에 대한 높은 안정성 때문에 저항 물질로 사용되는 가장 일반적인 물질이다. 본 연구에서는 $Ni_{72}Cr_Al_3Mn_4Si$(wt%)이 첨가된 우수한 저항특성을 갖는 S-type의 Evanohm 합금 타겟과 스퍼터링 장비를 이용하여 박막 저항을 제조하였다. 또한 열처리 조건을 $200^{\circ}C$, 300$300^{\circ}C$, $400^{\circ}C$, $500^{\circ}C$로 변화시키면서 고주파 박막 저항의 미세구조와 전기적 특성을 관찰하여 최상의 열처리 조건을 알아보았다.

• 한국마이크로전자및패키징학회:학술대회논문집
• /
• 한국마이크로전자및패키징학회 2003년도 기술심포지움 논문집
• /
• pp.145-150
• /
• 2003

최근에 3 GHz이상의 고주파용 전자부품과 소자의 제조에 낮은 TCR 값과 높은 정밀도를 갖는 박막저항이 사용되고 있다. Ni-Cr 박막저항은 낮은 TCR 값과 저항에 대한 높은 안정성 때문에 저항 물질로 사용되는 가장 일반적인 물질이다. 본 연구에서는 $Ni_{72}Cr_{20}Al_3Mn_4Si(wt\%)$ 첨가된 우수한 저항특성을 갖는 s-type의 Evanohm 합금 타겟과 스퍼터링 장비를 이용하여 박막 저항을 제조하였다. 또한 열처리 조건을 $200^{\circ}C,\;300^{\circ}C,\;400^{\circ}C,\;500^{\circ}C$로 변화시키면서 고주파 박막저항의 미세구조와 전기적 특성을 관찰하여 최상의 열처리 조건을 알아보았다.

• 한국정보통신학회논문지
• /
• 제7권3호
• /
• pp.468-473
• /
• 2003

본 연구에서는 박막트랜지스터의 특성 향상을 위하여 강유전성 박막을 게이트 절연층으로 사용하기 위하여 강유전성 박막과 a-Si:H의 계면특성을 조사하였다. 먼저 강유전성 박막 중에 대표적인 SrTiO$_3$를 I-BEAM 증착기로 박막을 형성시켰다. 형성된 박막은 N2 분위기에서 $150^{\circ}C∼600^{\circ}C$로 1시간 ANNEALING하여 전자현미경으로 표면을 측정하였다. SrTiO$_3$의 유전상수는 50∼100 정도였으며 항복전계는 1∼l.5 MV/cm로 매우 우수한 유전특성을 갖고 있었다. 강유전체 박막 위에 a-SiN:H,a-Si:H(n-type a-Si:H) 등을 PECVD로 증착하여 MFNS구조를 형성하였다. 계면특성을 C-V PLOTTER로 측정한 결과 SrTiO$_3$ 박막은 SiN과의 접합이 매우 안정되어 있었고 C-V특성은 SiN/a-Si:H과 유사하였다. 그러나 FERROELECTRIC/a-S:H의 경우가 훨씬 CAPACITANCE 값이 컸으며, 이는 강유전체 박막의 높은 유전상수에 기인 된 것이라 생각된다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 하계학술대회 논문집 Vol.8
• /
• pp.348-349
• /
• 2007

This paper describes the electrical characteristics of polycrystalline (poly) 3C-SiC thin film diodes, in which poly 3C-SiC thin films on n-type and p-type Si wafers, respectively, were deposited by APCVD using HMDS, Hz, and Ar gas at $1180^{\circ}C$ for 3 hr. The schottky diode with Au/poly 3C-SiC/Si(n-type) structure was fabricated. Its threshold voltage ($V_d$), breakdown voltage, thickness of depletion layer, and doping concentration ($N_D$) values were measured as 0.84 V, over 140 V, 61nm, and $2.7\;{\times}\;10^{19}\;cm^3$, respectively. The p-n junction diodes fabricated on the poly 3C-SiC/Si(p-type) were obtained like characteristics of single 3C-SiC p-n junction diodes. Therefore, poly 3C-SiC thin film diodes will be suitable microsensors in conjunction with Si fabrication technology.

• 한국전기전자재료학회논문지
• /
• 제36권2호
• /
• pp.170-174
• /
• 2023

Nickel oxide is a nonstoichiometric transparent conductive oxide with p-type conductivity, a wide-band energy gap of 3.4~4.0 eV, and excellent chemical stability, making it a very important candidate as a material for bipolar devices. P-type conductivity in Transparent Conductive Oxides (TCO) is controlled by the oxygen vacancy concentration. During the TCO film deposition process, additional oxygen diffusing into the NiO structure causes the formation of Ni 3p ions and Ni vacancies. This eventually affects the hole concentration of the p-type oxide thin film. In this work, the surface morphology and the electrical characteristics were confirmed in accordance with the annealing atmosphere of the nickel oxide thin film.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제40회 동계학술대회 초록집
• /
• pp.87-87
• /
• 2011

Oxide semiconductors are attractive materials for thin-film electronics and optoelectronics due to compatibility with synthesis on large-area, glass and flexible substrate. However, development of thin-film electronics has been hampered by the limited number of semiconducting oxides that are p-type. We report on the effect of the oxygen partial pressure ratio in the gas mixture on the electrical and optical properties of spinel Mg:$ZnCo_2O_4$ thin films deposited at room temperature using RF sputtering, that exhibit p-type conduction. The thin-films are deposited at room temperature in a background of oxygen using a polycrystalline Mg:$ZnCo_2O_4$ ablation target. The p-type conduction is confirmed by positive Seebeck coefficient and positive Hall coefficient. The electrical resistivity and carrier concentration in on dependent Mg:$ZnCo_2O_4$ thin films were found to be dependent on the oxygen partial pressure ratio. As a result, it is revealed that the Mg:$ZnCo_2O_4$ thin-films were greatly influenced on the electrical and optical properties by the oxygen partial pressure condition. The visible region of the spectrum of 36~85%, and hole mobility of 1.1~3.7 $cm^2$/Vs, were obtained.

• 전기학회논문지
• /
• 제59권7호
• /
• pp.1255-1258
• /
• 2010

In this paper, the $CoSi_2$ thin films with thicknesses of about $5{\mu}m$ were deposited on n-type silicon (111) substrates by RF magnetron sputtering method using a $CoSi_2$ target (99.99%). The flow rate of argon of 50 sccm, substrate temperature of $100^{\circ}C$, RF power of 60 watts, deposition time of 30 minutes, and the vacuum of $1\times10^{-6}$ Torr. The annealing treatments of the $CoSi_2$ thin film were performed from 500, 700 and $900^{\circ}C$ for 1h in air ambient by an electric furnace. In order to investigate the $CoSi_2$ thin film X-ray diffraction patterns were measured using the X-ray diffractometer (XRD). The structure of the thin films were investigated by using scanning the electron microscope (SEM) were used for review. The surface morphology of the thin films was measured with a atomic force microscopy (AFM). Temperature dependence of sheet resistivity and property of Hall effect was measured in the $CoSi_2$ thin film.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 하계학술대회 논문집 Vol.8
• /
• pp.152-153
• /
• 2007

$CuInSe_2$ single crystal thin film was deposited on thoroughly etched semi-insulating GaAs(100) substrate by the hot wall epitaxy (HWE) system. After the as-grown $CuInSe_2$ single crystal thin films was annealed in Cu-, Se-, and In-atmospheres, the origin of point defects of $CuInSe_2$ single crystal thin films has been investigated by the photoluminescence(PL) at 10 K. The native defects of $V_{Cu}$, $V_{Se}$, $Cu_{lnt}$, and $Se_{lnt}$ obtained by PL measurements were classified as a donors or acceptors type. And we concluded that the heat-treatment in the Cu-atmosphere converted $CuInSe_2$ single crystal thin films to an optical n-type. Also, we confirmed that In in $CuInSe_2$/GaAs did not form the native defects because In in $CuInSe_2$ single crystal thin films existed in the form of stable bonds.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 하계학술대회 논문집
• /
• pp.319-320
• /
• 2009

In this study, high-quality Al-N doped p-type ZnO thin films were deposited on n-type Si (100) wafer or Si coated with buffer layer by DC magnetron sputtering in the mixture of $N_2$ and $O_2$ gas. The target was ceramic ZnO mixed with $Al_2O_3$ (2 wt%). The p-type ZnO thin film showed higher carrier concentration $2.93\times10^{17}cm^{-3}$, lower resistivity of $5.349\;{\Omega}cm$ and mobility of $3.99\;cm^2V^{-1}S^{-1}$, respectively. According to PL spectrum, the Al donor energy level depth ($E_d$) of Al-N codoped p-type ZnO film was reduced to about 51 meV, and the N acceptor energy level depth ($E_a$) was reduced to 63 meV, respectively.

• 한국재료학회지
• /
• 제13권2호
• /
• pp.111-114
• /
• 2003

Effects of substrate materials on the microstructure and the sensitivity of $SnO_2$thin film gas sensors have been studied. Various substrates were studied, such as oxidized silicon, sapphire, polished alumina, and unpolished alumina. It was observed that strong correlation exists between the electrical resistance and the CO gas sensitivity of the manufactured sensors and the surface roughness of $SnO_2$thin films, which in turn was related to the surface roughness of the original substrates. X$SnO_2$thin film gas sensor on unpolished alumina with the highest surface roughness showed the highest initial resistance and CO gas sensitivity. The transmission electron microscopy observation indicated that shape and size of the columnar microstructure of the thin films were not critically affected by the type of substrates.