• The Transactions of the Korean Institute of Power Electronics
• /
• v.10 no.2
• /
• pp.169-176
• /
• 2005

In this paper, a DC and small-signal AC modeling for the active-clamp, ful1-bridge boost converter is described. Based on the operation principle, the ac part of the converter can be replaced by a dc counterpart. Then, a conceptual equivalent circuit is derived by rearranging the switches. The equivalent circuit for this converter consists of CCM(Continuous conduction mode) boost and DCM(Discontinuous conduction mode) buck converter. The analyses for the equivalent CCM boost and DCM buck converter are done using the model of PWM switch. The theoretical modeling results are confirmed through experiment or SIMPLIS simulation.

• Journal of Advanced Marine Engineering and Technology
• /
• v.24 no.5
• /
• pp.42-51
• /
• 2000

The performances of the simple expansion, perforated tube, and conical-connector type as an exhaust muffler are shown in this study. Applying a model in which the method of four-pole parameter is used makes theoretical estimation of the insertion loss. Experiment is performed for the measurement of the insertion loss under four cases according to the variation of the tail pipe length. By comparing the theoretical prediction with the experimental results, the validity of the modeling using the method of four-pole parameter is verified. The personal computer simulation programs for the above mentioned theory on the muffler design have been developed and exhaust sound level measurements have been carried out for simple expansion muffler, conical-connector muffler, perforated tube mufflers and the combined type of conical-connector and simple expansion muffler. The measured results for attenuation characteristics of noise for each muffler are compared with the computed theoretical results to verity the confidence and applicable limits of the theoretical equation derived.

• 한국경영정보학회:학술대회논문집
• /
• 2008.06a
• /
• pp.29-34
• /
• 2008

This study examines the effects of information and communication technologies on individual performance. The literature has paid a considerable amount of attention to social influence as a determinant of individual behavior. We combine task-technology fit with concepts from adaptive structuration theory to specify social influence. In our model, we suggest that individuals should receive support from proper social construction to have additional performance improvement. Empirical data from 317 individuals across 43 teams in 10 companies is used to assess the theoretical model. Our theoretical model received support from the data.

• Journal of Information Display
• /
• v.10 no.3
• /
• pp.101-106
• /
• 2009

In this study, a physical OLED analog behavior model for SPICE simulation was described using the Verilog-A language. The model was presented through theoretical equations for the J-V characteristics of OLED derived according to the internalcarrier emission equation based on a diffusion model at the Schottky barrier contact, and the mobility equation based on the Pool-Frenkel model. The accuracy of this model was examined by comparing it with the results of the device simulation that was conducted.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.11a
• /
• pp.471-475
• /
• 2001

This paper is concerned with the experiments on the dynamic characteristics and active vibration control of plate with piezoceramic sensors and actuators. The experimental frequency response plots can be used to verify the theoretical modeling. The active vibration control was achived by using a single-input single-output positive position feedback controller. Theoretical analysis will follow.

• Korea-Australia Rheology Journal
• /
• v.13 no.3
• /
• pp.109-123
• /
• 2001

A stress jump, defined as the instantaneous gain or loss of stress on startup or cessation of a deformation, has been predicted by various models and has relatively recently been experimentally observed. In 1993, Liang and Mackay measured shear stress jump data of xanthan gum solutions, and in 1996, Orr and Sridhar reported extensional stress jump data of Boger fluids. Shear stress jumps of suspensions and liquid crystal polymers have also been observed. In this contribution, experimental work as well as a variety of theoretical models, which are able to predict a stress jump, are reviewed.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2003.11a
• /
• pp.233-235
• /
• 2003

The voltage and current of fluoescent lamp has been successfully calculated in the case of frequency variation. Energy states of mercury atom in the discharge process are regarded as six levels. These calculations have been accurately solved by numerically employing mixed the FDM and the 2nd Runge-Kutta method. The theoretical calculation results and experimental results were presented to verify the feasibility of the modeling. Calculation and experimental results were presented to verify the feasibility of the calculation.

• Structural Engineering and Mechanics
• /
• v.67 no.4
• /
• pp.385-390
• /
• 2018

An incongruity is underlined about the analysis of Timoshenko beams subjected to concentrated loads modelled through the use of generalized functions. While for Euler-Bernoulli beams this modeling always leads to effective results, on the contrary, the contemporary assumptions of concentrated external moment, interpreted as a generalized function (doublet), and of shear deformation determine inconsistent discontinuities in the deflection laws. A physical/theoretical explanation of this not-neglecting incongruity is given in the text.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1997.10a
• /
• pp.558-563
• /
• 1997

A thermal sizing code, named as HSGSA (Helical coil Steam Generator Sizing Analyzer), for a sodium heated helical coil steam generator is developed for KALIMER (Korea Advanced LIquid MEtal Reactor) design. The theoretical modeling of the shell and tube sides is described and relevant correlations are presented. For assessment of HSGSA, a reference plant design case is compared to the calculational outputs from HSGSA simulation.

• Proceedings of the KIEE Conference
• /
• 2005.07b
• /
• pp.1492-1495
• /
• 2005

This paper presents a study on the modeling on the dimming control of electronic fluorescent lamp. The resulted models of the lamps were applied the two dimming control methods, one is the variable switching frequence and the other is the variable dc link voltage method. And the comparison of the dimming characteristics between the two methods was presented. Theoretical predictions were verified the experimental results on a 100w electrodeless fluorescent lamp.