• Bulletin of the Korean Chemical Society
• /
• v.33 no.1
• /
• pp.167-170
• /
• 2012

A test-area molecular dynamics simulation method for the vapor-liquid interface of argon through a Lennard-Jones intermolecular potential is presented in this paper as a primary study of interfacial systems. We found that the calculated density profile along the z-direction normal to the interface is not changed with time after equilibration and that the values of surface tension computed from this test-area method are fully consistent with the experimental data. We compared the thermodynamic properties of vapor argon, liquid argon, and argon in the vapor-liquid interface. Comparisons are made with kinetic and potential energies, diffusion coefficient, and viscosity.

• Proceedings of the KOSOMBE Conference
• /
• v.1990 no.05
• /
• pp.43-46
• /
• 1990

Modern society is prevailed a lot of allergies. So, the allergy test is very important. There are many kinds of allergy test. A doctor usually uses skin allergy test among many allergy tests. However, little standadization and objectivity of grading-standard has been established in the skin allergy test. A measurement of the reaction area has been a major objective to perform skin allergy test. Recently, a doctor's method is to measure the reaction area after drawing a line that represents the reaction area on the skin. But this method differs slightly from the real reaction area and individual doctor's measurement is different, because the edge of the reaction area is obscure. In this paper, we propose a algorithm which is able to detect vague edges using the fuzzy set. The algorithm that detects the line and curve is proposed first. Here, the maximum value is calculated by comparing the membership function of the line and curve seperately. We also encode the direction of the line and curve by using 8-direction code. Then, we calculate the reaction area by measuring the pixels which are inside the reaction area. And finally the Allergy grade is decided by grading-standard, and we accomplish faster, the 80re accurate and objective allergy grade decision.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.10a
• /
• pp.639-642
• /
• 1999

Pullout test known as Lok test among the test methods to evaluate concrete strength strength is a test method which is used to decide the form removal time by assessing the early strength of concrete in a new construction, or to control the quality of newly placed concrete. This method has inconvenience to place inserts on the form work in advance, however, the placing work is quite simple and it has advantage that the strength can be measured at field as long as the inserts are placed. In this study, the first step is to investigate the properties of test method itself, by performing the laboratory test which covers deviation of the method and factors affecting the results, etc. The second step is to correlate the result with cylinder strength and other NDT methods such as rebound hammer, ultrasonic method, etc. And that, the results are compared with foreign results to find the differences between the two. In this research, new factors such as moisture content, area of aggregate failure cross section and area of aggregate separation cross section, etc as well as wate-cement ratio and age are investigated.

• Tribology and Lubricants
• /
• v.38 no.4
• /
• pp.128-135
• /
• 2022

In the product development process, the reliability of the product can be secured through durability tests. However, since the durability test method is expensive and time consuming, a method to save time and money by utilizing virtual product development (VPD) is required. However, research on the accuracy of the results of virtual product development is required. In this paper, an accelerated durability test was designed and conducted using a planetary gear decelerator. And an analysis model under the same conditions was created and simulated. To correlate the results of the experiment with the results of the analytical model, created a model that can discriminate the wear region using one of the data mining methods, the k-means algorithm method and HSV (Hue, Saturation, Value). The wear area is compared by counting the number of pixels defined as wear through a discrimination model. A similar ratio was calculated by comparing the pixel ratio of the area determined as wear in the entire area. It showed a similar ratio of about 70%, and it is necessary to improve the discrimination method.

• Journal of the Korean Operations Research and Management Science Society
• /
• v.36 no.4
• /
• pp.143-160
• /
• 2011

In the marketing research area, service quality and customer satisfaction have been considered as ones of the most important marketing variables. However, there has been a lot of controversy over the direction of the casual relationship between the service quality and the customer satisfaction. The purpose of this study is to investigate the casual relationship between the service quality and the customer satisfaction. Granger's test of casuality method has been used to test the casuality relationship between two variables. In this paper, we applied the Granger's test of casuality method to KS-SQI and NCSI data of 17 business area which had been gathered annually. As the research result, we found that the customer satisfaction might cause the service quality in many service area.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.30 no.11 s.254
• /
• pp.1335-1347
• /
• 2006

Surface energies calculated from measured contact angles between several solutions and test samples, such as Si wafer, $Al_2O_3$, $SiO_2$, PTFE(Polytertrafluoroethylene), and DLC(Diamond Like Carbon) films, based on geometric mean method and Lewis acid base method. In order to relate roughness to adhesion force, surface roughness of test samples were scanned large area and small by AFM(Atomic Force Microscopy). Roughness was representative of test samples in large scan area and comparable with AFM tip radius in small scan area. Adhesion forces between AFM tip and test samples were matched well with order of roughness rather then surface energy. When AFM tips having different radius were used to measure adhesion force on DLCI film, sharper AFM tip was, smaller adhesion force was measured. Therefore contact area was more important factor to determine adhesion force.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.58 no.2
• /
• pp.45-52
• /
• 2016

The object of this paper was to evaulate modified proposed design equation in model test result in order to estimate uplift-resistance of timber pile of reclaimed land greenhouse foundation. Uplift resistance result of model test was increased to according to increased of contact area. Uplift-resistance result of field test tend to lineary increased to according to increased of embedment depth and contact area. Results of field uplift-resistance was evaluate compare with modified proposed design equation results of model test and Effective stress method. As the Effective stress method tend to underestimate, modified proposed design equation results of model test tend to similar type. As the contact area increase, difference between field uplift-resistance results and modified proposed design equation results of model test was considered uplift-speed.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2012.11a
• /
• pp.77-79
• /
• 2012

This paper intends to review possible application in the high strength area through compressive strength estimation of the simulated high strength concrete member using Rock Test Hammer and suggest it as a reference data for the strength estimation technique of the ultra high strength concrete in the future. From the results of our test, in the low strength area less than 15MPa and normal strength area in 15~60MPa, as shown on the existing studies, it is indicated that P Type Schmidt Hammer in the low strength area and N Type Schmidt Hammer in the normal strength area have high correlation of rebound-compressive strength. As the Rock Test Hammer indicated more or less reduced accuracy in the low strength area and the normal strength area but high correlation on the high strength area (50~100MPa) defined on this test, it is determined that it would be possible to make the fastest and simplest compressive strength estimation on the site where the high strength concrete is applied.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.10a
• /
• pp.1340-1352
• /
• 2008

In this study, S-wave velocity range is gauged in every field test method at the total 5 locations in the marine deposits in Incheon area. field test method is accomplished the SPT(Standard Penetration Test), CPT(Cone Penetration Test), SPS(Suspension PS Logger), SCPT (Seismic Cone Penetration Test) and so on. The S-wave velocity of SCPT in the downhole test method is measured lower than SPS logger at the N value > 15 range. But at the N value < 15 range, SPS logger and SCPT result is measured same. In this result, although the soil strength of the downhole test method increased, the rate of S-wave velocity is tend to be slowed. This result shows that the downhole test is difficult to apply at the place that the intensity of soil is more extreme and harder soil. And it shows that the existing Imai(1982) type that is mostly used within the country is not suitable for the marine deposits. Thus, the empirical formula that can show the range of S-wave velocity in each N value for domestic soil is needed.

• ETRI Journal
• /
• v.36 no.6
• /
• pp.942-952
• /
• 2014

This paper presents a novel test point insertion (TPI) method for a pseudo-random built-in self-test (BIST) to reduce the area overhead. Recently, a new TPI method for BISTs was proposed that tries to use functional flip-flops to drive control test points instead of adding extra dedicated flip-flops for driving control points. The replacement rule used in a previous work has limitations preventing some dedicated flip-flops from being replaced by functional flip-flops. This paper proposes a logic cone analysis-based TPI approach to overcome the limitations. Logic cone analysis is performed to find candidate functional flop-flops for replacing dedicated flip-flops. Experimental results indicate that the proposed method reduces the test point area overhead significantly with minimal loss of testability by replacing the dedicated flip-flops.