• 한국구조물진단유지관리공학회 논문집
• /
• 제27권5호
• /
• pp.139-146
• /
• 2023

In this study, compressive strength and adhesion strength were measured as repair materials to evaluate the mechanical and electrical properties of compression and shear specimens with self-sensing repair materials. As a result of the experiment, the strength improvement rate of the compression test specimen was higher than the section enlargement area ratio, but the shear test specimen did not show an improvement in strength as much as the section enlargement area ratio. Compression experiments under load showed high correlation between FCR-Strain and FCR-Stress, confirming self-sensing performance. However, the shear test did not show as much correlation as the compression test. Accordingly, it is judged that the self-sensing repair material is suitable for the compression member on which the compression load acts in the building.

• Physical Therapy Rehabilitation Science
• /
• 제9권4호
• /
• pp.275-280
• /
• 2020

Objective: Compression wear is an external aid which promotes performance and recovery, diminishes muscular microtrauma, reduces muscle fiber recruitment, improves neuromechanics, enhances coordinative activities, and reduces the perceived exertion. The purpose of this study was to investigate the relationship between athletic taping and compression wear on dynamic postural balance in healthy young men. The hypothesis was that the athletic taping and compression wear would affect dynamic postural balance, with athletic taping having a different effect on dynamic postural balance in healthy young adults. Design: Cross-sectional study. Methods: Thirty-seven healthy young men participated in this study. To examine the association between athletic taping and compression wear, 3 clinical measurement tools, including 5 times sit-to-stand (5xSTS), one-leg standing (OLS) test, and Y-balance test (YBT) in 5 different conditions, namely (1) non-supporting, and support with (2) athletic taping, (3) regular compression wear, (4) silicon compression wear, and (5) double-fiber compression wear were used. Results: The distance of the Y-balance test (YBT) on both the dominant and non-dominant sides showed a statistically difference among the 5 supporting conditions (p<0.05). The distance measured via the YBT in the non-support condition was significantly different than that in the other four supporting conditions (p<0.05). However, 5xSTS and OLS were not significantly different in these supporting conditions. Conclusions: The results of this study suggest that athletic taping, silicon compression wear, and double-fiber compression wear were more effective for dynamic balance than non-supporting and regular compression wear.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2002년도 ITC-CSCC -1
• /
• pp.228-230
• /
• 2002

We present a new low power scan testing and test data compression method for System-On-a-Chip (SOC). The don't cares in unspecified scan vectors are mapped to binary values for low power and encoded by adaptive encoding method for higher compression. Also, the scan-in direction of scan vectors is determined for low power. Experimental results for full-scanned versions of ISCAS 89 benchmark circuits show that the proposed method has both low power and higher compression.

• 한국농공학회지
• /
• 제38권3호
• /
• pp.70-81
• /
• 1996

Solutions of geotechnical engineering problems require predictions of deformation and stresses during various stages of loading. Powerful numerical methods are available to make such predictions even for complicated problems. To get accurate results, realistic stress-strain relationships of soils are dependent on a number of factors such as soil type, density, stress level and stress path. Attempts are continuously being made to develope analytical models for soils incorporating all such factors. Isotropic compression-expansion test and a series of drained conventional triaxial tests with several stress path for Baekma river sand were performed to investigate stress-strain and volume change characteristics of Lade's single work hardening model dependant on the stress path. In order to predicted of stress-strain and volumetric strain behavior were determined the values of parameters for the mode by the computer program based on the regression analysis. Predicted stress-strain behavior of triaxial compression tests and optional stress path tests for increasing confining pressure with parameters obtained conventional triaxial compression tests agreed with several test results but the prediction results for decreasing confining pressure reduced triaxial compression tests make a little difference with test results.

• 한국운동역학회지
• /
• 제26권4호
• /
• pp.421-426
• /
• 2016

Objective: The purpose of this study was to investigate how different levels of compression exerted on the femoral region (known as the power zone) by coated fabric influences the activation and anaerobic capacity of the rectus femoris. Method: Three different levels of compression on the rectus femoris of the participants, namely 0% (normal condition), 9% (downsize), and 18% (downsize), were tested. The material of the fabric used in this study was nonfunctional polyurethane. Surface electromyography test was used to investigate the activation of the rectus femoris, while the isokinetic test (Cybex, $60^{\circ}/sec$) and Wingate test were used to investigate the maximum anaerobic power. Results: The different compression levels (0%, 9%, and 18%) did not improve the strength and anaerobic capacity of the knee extensor. However, knee flexor interfered with activation of the biceps femoris, which is an agonist for flexion, during 18% compression. Conclusion: Compression garments might improve the stretch shortening cycle effect at the time of eccentric contraction and during transition from eccentric to concentric contraction. Therefore, future studies are required to further investigate these findings.

• 한국콘텐츠학회논문지
• /
• 제5권4호
• /
• pp.188-196
• /
• 2005

본 논문에서는 테스트 시간과 전력소모를 감축할 수 있는 새로운 테스트 데이터 압축 및 저전력 스캔 테스트 방법을 제안하였다. 제안된 방법은 수정된 스캔 셀 재배열과 하이브리드 적응적 부호화 방법을 사용하여 scan-in전력과 테스트 데이터 량을 줄였으며 하이브리드 테스트 데이터 압축방법은 Golomb Code와 런길이(run-length) 코드를 테스트 데이터내의 런(run) 길이에 따라서 적응적으로 적용하는 방법이다. 또한 scan-in 전력소모를 최소화하기 위해서 스캔 벡터내의 열 해밍거리를 이용하였다. ISCAS89 벤치마크 회로에 적용하여 실험한 결과, 모든 경우에 있어서 테스트 데이터 및 전력소모를 효율적으로 감소시켰으며 압축률은 17%-26%, 평균 전력소모는 8%-22%, 최고전력소모는 13%-60% 정도의 향상률을 보였다.

• 대한전자공학회논문지SD
• /
• 제45권9호
• /
• pp.57-64
• /
• 2008

본 논문은 높은 압축 성능을 가진 테스트 데이터 압축 기법을 제안한다. 제안하는 기법은 돈 케어 리맵핑을 이용한 천이 추가 단계와 천이 이전 단계로 구성된다. 실험 결과는 새로운 기법이 가장 높은 성능의 기법들 중 하나인 RL-huffman보다 높은 압축률을 제공하고 더 작은 하드웨어 면적을 필요로 함을 보여준다. 따라서 이 기법은 테스트 데이터 압축을 위한 실제적인 해법으로 널리 쓰일 수 있다.

• 복합신소재구조학회 논문집
• /
• 제5권1호
• /
• pp.16-21
• /
• 2014

In the study, tensile, compression and in-plane tests about longitudinal direction of glass fiber were performed. Also, to obtain the material properties of GFRP fabric composite, tensile test was performed. All test were performed by the test method of ASTM. Maximum compressive strength was smaller than the maximum tensile strength at the longitudinal direction test results. Elastic modulus of the tensile and compressive was almost similar at the compression test results in the longitudinal direction. Based on the GFRP fabric composite test results, GF91 was showed good performance at maximum compressive, maximum strain and elastic modulus.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2001년도 추계학술대회 논문집
• /
• pp.345-348
• /
• 2001

Nowadays, cast ingots has been used as preforms for forging to reduce the cost and the number of processes. In this study, the forging ability of Al cast alloys was investigated by using hot compression tests. Hot compression behavior of the cast Al alloys has been studied The flow stress increased by decreasing the compression temperature and by increasing the strain rate. In case of melt treatment the flow stress decreased comparing to untreated A356.0 Al alloy. Also, We developed the various forged lower control arm using the cast preform. The optimum design of product and cast preform was investigated After Prototyping of Al forged lower arm, durability and buckling test were performed.

• 소성∙가공
• /
• 제10권4호
• /
• pp.319-328
• /
• 2001

Quantitative evaluation of the tribological conditions at the tool-workpiece interface in metal forming is usually accomplished by the ring compression test. This paper describes an experimental investigation into friction factor under warm forming conditions according to the lubricants and the lubricating methods using the ring compression test. Four different lubricants, two water based graphite and two oil based graphite lubricants, and three different lubricating methods were applied in the experiments. Calibration curves with the friction shear factor were obtained using FEM analysis and verified by the experimental results. The influence of lubricant and lubricating methods on friction are discussed. In the ring compression test, the lower friction factor got to spray the oil based lubricant on die and billet in warm forging temperature.