• 수산해양기술연구
• /
• 제35권1호
• /
• pp.1-10
• /
• 1999

The north-west sea area of Cheju Island is where originate two layer current in the summer season. The case of the fishing operations in this sea area is almost impossible for normal expansion of the net gear for shooting net, and is happened to be frequent occasions for rise of tension suddenly in purseline by changes of the net shapes in the operation. Therefore, the safety of the operations is often obstructed by the above mentioned. In connection with the above, model experiments on the purse seine in the circulating water tank was carried out in comparison and analysis on the changes of tension in the pruseline by deformation of purse seine in the sea area of two layer current. THe results obtained are as follows;In the case of the required time for pursing of 20 minutes in the no current set, the increasing curve for tension of purseline can be expressed as:Y=0.0004x3+0.0098x2+0.3000x(r=0.9989)where Y is tension(metric tons) of a purseline, x is required time(minutes) for pursing. And, the maximum value of tension in this time was an increase of 31.3 percent at 15 minutes, and was a decrease of 30.3 percent at 30 minutes than that of 20 minutes.When the bottom margin of net is held on the position in velocity of 0.5 knot at three-eighths of net in the bottom current to the net height, the maximum tension of the required time for pursing of 30 minutes in tight set and loose set were decrease of 29.5 percent and 28.7 percent respectively than that of 20 minutes.The work load during the required time for pursing of 20 minutes were calculated 5.79×106 kgf·m in no current set, 7.89×106 kgf·m in tight set and 5.15×106 kgf·m in loose set, therefore it was an increase of 22.3 percent in tight set, and was a decrease of 11.1 percent in loose set than that of the no current set. Where tight set and loose set is a range of the bottom current with velocity of 0.5 knot at three-eighths of net to the net height.

• The Korean Journal of Physiology
• /
• 제2권1호
• /
• pp.39-45
• /
• 1968

Recently, in this department, pressure-displacement curve and breaking tension of dog and human tympanic membrane were studied using intact, fresh or dried tympanic membrane attached to external auditory meatus. However, physical property, proper elasticity-Young Modulus, of the tympanic membrane has not been clarified yet. Present study is attempted to further clarify proper Young Modulus of tympanic membrane, and to distinguish possible difference between layer of stratum radiatum and layer of stratum circulare of tympanic membrane in breaking tension and in Young Modulus. Tympanic membrane was excised from sacrificed dog, and preparation was made into the size of approximately 1 mm in width and 3 mm in length. In fresh or dried tympanic membrane, which was dried at $80^{\circ}C$ for 24 hrs., some preparations were made along the long axis parallel to the fibers of radial direction, and others were made along the long axis perpendicular to the radial fibers-circular direction. Breaking tension and displacement according to loading, were measured and Young Modulus was calculated in tympanic membrane preparations under the different experimental conditions. Results obtained are summarized as follows : 1. Young Modulus of fresh tympanic membrane in radial direction was $6.57{\times}10^8\;dyne/cm^2$, and that of fresh preparation in circular direction was $1.68{\times}10^8\;dyne/cm^2$. The Young Modulus of fresh tympanic membrane in radial direction resembles to that of silk and whale moustache. In dried tympanic membrane, Young Modulus of preparation of radial direction was $30.2{\times}10^8\;dyne/cm^2$ and that of preparation in circular direction was $25.0{\times}10^8\;dyne/cm^2$. 2. Breaking tension of fresh tympanic membrane was 44.9 gm/mm in radial preparation, and 7.9 gm/mm in circular preparation. In dried tympanic membrane, breaking tension was 46.7 gm/mm in preparation of radial direction, and 17.2 gm/mm in preparation of circular direction. 3. Much smaller breaking tension of the circular preparation-one fifth to the radial preparation-seemed to be responsible for the higher incidence of circular fiber breaking in tympanic membrane performation caused by trauma or sudden change in atmospheric pressure. 4. The correlation seemed to be very close between breaking tension and Young Modulus in tympanic membrane.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문집
• /
• pp.244-249
• /
• 2002

Rubber seat is extensively used to reduce the vibration of machine or structure. Over the years an enormous effort has been put into developing procedures to provide properties of rubber material for design function. However, there are still a lot of difficulties to analyze static characteristics of rubber components with hyper elasticity and nonlinear large deformation. In this paper material property is obtained by strain-stress curve using a tension test. Mooney-Rivlin Coefficients are gotten by fitting strain-stress curve. The visco-elastic characteristics of refrigerator rubber mount is determined by using ANSYS. And to minimize the rubber stiffness, the rubber seat shape optimization is performed.

• Computers and Concrete
• /
• 제16권1호
• /
• pp.179-190
• /
• 2015

An experimental program has been carried out to investigate the effect of edge-slope on compressive strength of concrete specimens. In this study, effect of such slope was investigated by testing 100 standard cylinder specimens and 40 standard cubes. When molds are put on a slanted place, wet concrete starts to flow through the open end of mold. It keeps flowing until it reaches to a parallel surface with the place over which it was placed. That creates a sloped surface over the loading area. Experimental results revealed significant relationships between failure loads and slope of loading surface for cylinders. Angled cracks occurred in sloped cylinder specimens. Tension cracks occurred in cube specimens. Fracture mechanisms were also evaluated by using finite element analyses approach. Experiments yielded an exponential curve with bandwidth for cylinders. Average value of curve is $y={\frac{\pi}{2}}e^{-cf}$ between slope and compressive strength. Inclination is much effective parameter for cylinders than cubes.

• Steel and Composite Structures
• /
• 제34권5호
• /
• pp.671-679
• /
• 2020

The new energy-based criterion, named Reinforcement Strain Energy Density (ReiSED), is proposed to investigate the fracture behavior of the cracked orthotropic materials in which the crack is embedded in the matrix along the fibers. ReiSED is an extension of the well-known minimum strain energy density criterion. The concept of the reinforced isotropic solid as an advantageous model is the basis of the proposed mixed-mode I/II criterion. This model introduces fibers as reinforcements of the isotropic matrix in orthotropic materials. The effects of fibers are qualified by defining reinforcement coefficients at tension and shear modes. These coefficients, called Reduced Stress (ReSt), provide the possibility of encompassing the fiber fraction in a fracture criterion for the first time. Comparing ReiSED fracture limit curve with experimental data proves the high efficiency of this criterion to predict the fracture behavior of orthotropic materials.

• Journal of Welding and Joining
• /
• 제28권2호
• /
• pp.91-95
• /
• 2010

Stress distribution and deformation on the CT-type(Cross Tension type) spot welded lap joint subjected to out of plane tensile load were investigated by finite element method. Using the maximum principal stresses at the nugget edge obtained by FEM analysis, evaluated the fatigue strength of the CT-type spot welded lap joints having various dimensions and materials. and also, the influence of the geometrical parameters of CT-type spot welded lap joints on stress distribution and fatigue strength must be evaluated. thus, in this paper, ${\Delta}P-N_f$ curve were obtained by fatigue tests. Using these results, ${\Delta}P-N_f$ curve were systematically rearranged in the $\Delta\sigma-N_f$ relation with the hot spot stresses at the CT-type spot welded lab joints. It was found that the proposed $\Delta\sigma-N_f$ relation could provide a more reasonable fatigue design criterion for the CT-type spot welded lap joints.

• Steel and Composite Structures
• /
• 제34권4호
• /
• pp.581-597
• /
• 2020

Light-Weight Concrete containing Expanded Poly-Styrene Beads (EPS-LWC) is an approved structural and non-structural material characterized by a considerably lower density and higher structural efficiency, compared to concrete containing ordinary aggregates. The experimental campaign carried out in this project provides new information on the mechanical properties of structural EPS-LWC, with reference to the strength and tension (by splitting and in bending), the modulus of elasticity, the stress-strain curve in unconfined compression, the absorbed energy under compression and reinforcement-concrete bond. The properties measured at seven ages since casting, from 3 days to 91 days, in order to investigate their in-time evolution. Mathematical relationships are formulated as well, between the previous properties and time, since casting. The dependence of the compressive strength on the other mechanical properties of EPS-LWC is also described through an empirical relationship, which is shown to fit satisfactorily the experimental results.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2000년도 가을 학술발표회논문집
• /
• pp.209-216
• /
• 2000

The purpose of this study is to investigate elasto-plastic behaviour and estimate ultimate resistance capacity of the residential-commercial building subjected to lateral force along the height of structure. Four types of residential-commercial building are chosen as analytical models and investigated by pushover analysis. Pushover analysis estimates initial elastic stiffness, post-yielding stiffness, and plastic hinges on each story of structures through three-dimensional nonlinear analysis program CANNY-99. Skeleton curve of bending stiffness model is bilinear, shear stiffness model is trilinear, and axial stiffness model is elastic. Skeleton curve of axial stiffness model has the axial compression and tension stiffness of reinforced concrete members. This study presents the change of inter story drift, story stiffness and hinge of story and member.

• Steel and Composite Structures
• /
• 제7권5호
• /
• pp.355-376
• /
• 2007

The purpose of this study is to predict and investigate the time-dependent creep behavior of composite materials. For this, firstly the evaluation method for the modulus of elasticity of whole fiber and matrix is presented from the limited information on fiber volume fraction using the singular value decomposition method. Then, the effects of fiber volume fraction on modulus of elasticity of GFRP are verified. Also, as a creep model, the nonlinear curve fitting method based on the Marquardt algorithm is proposed. Using the existing Findley's power creep model and the proposed creep model, the effect of fiber volume fraction on the nonlinear creep behavior of composite materials is verified. Then, for the time-dependent analysis of a composite material subjected to uniaxial tension and simple shear loadings, a user-provided subroutine UMAT is developed to run within ABAQUS. Finally, the creep behavior of center loaded beam structure is investigated using the Hermitian beam elements with shear deformation effect and with time-dependent elastic and shear moduli.

• 콘크리트학회논문집
• /
• 제21권1호
• /
• pp.13-20
• /
• 2009

본 연구에서는 섬유혼입률이 초고강도 강섬유보강 콘크리트의 인장연화거동 특성에 미치는 영향을 파악하고자 하였다. 노치 낸 보에 대한 3점 재하 휨실험을 통해 초고강도 강섬유보강 콘크리트의 휨인장 거동을 구하고, Uchida 등이 제안한 역해석법을 사용하여 휨 실험 결과로부터 인장연화곡선을 도출하였다. 노치 낸 보의 휨 실험 결과에서 초기강성은 섬유혼입률에 관계없이 일정한 값을 나타내고, 강섬유의 혼입률이 증가할수록 초고강도 강섬유보강 콘크리트의 휨인장강도는 증가하며 연화거동은 일정 균열폭에서 점근적으로 수렴하는 경향을 나타내었다. 역해석을 통해 구한 인장연화곡선으로부터 섬유혼입률과 임계균열폭, $\omega_0$의 함수로 인장연화모델을 제안하였으며, 인장연화모델은 균열이 진행됨에 따라 일정한 인장응력 값을 가지는 소성구간과 지수함수로 주어지는 연화구간으로 나누어 제시하였다. 본 연구에서 제시한 인장연화모델을 적용하여 점성균열모델을 이용한 유한요소해석을 수행한 결과, 해석 결과와 실험 결과와 잘 일치하는 것으로 나타났다.