• 한국생산제조학회지
• /
• 제9권4호
• /
• pp.48-55
• /
• 2000

For the Tailor Welded Blank sheet used for automobile body panel, the characteristics of fatigue strength and crack propagation behavior were studied. The thickness of specimens was joined to be same (0.9mm+0.9mm) and different (0.9mm+2.0mm) .As a base test, mechanical properties around weld zone were examined . The results indicated that there were no significant decreases in mechanical properties , but hardness around weld bead was 2.3 times greater than base material . The fatigue strength was the highest when the loading direction was parallel to the welding direction, which was about 85% of tensile strength of base material. It was decreased by 8.5% when the thickness of specimens and base metal was different, and it was increased by 25% when pres-strain was applied. The crack propagation rate was noticeably decreased around weld line and rapidly increased as it passed through weld line. Reviewing the shape of the crack propagation , crack width around weld line was around the weld zone due to retardation of crack growth , but is became narrow passing weld line due to decreased toughness.

• 한국초전도ㆍ저온공학회논문지
• /
• 제15권2호
• /
• pp.24-28
• /
• 2013

In this study, the homogeneity of critical current, $I_c$, along the lengthwise direction in the coated conductor (CC) tape under uniaxial tension was investigated using a multiple voltage tap configuration. Initially, a gradual and homogeneous $I_c$ degradation occurred in all subsections of the tape up to a certain strain value. This was followed by an abrupt $I_c$ degradation in some subsections, which caused scattering in $I_c$ values along the length with increasing tension strain. The $I_c$ degradation behaviour was also explained through n-value as well as microstructure analyses. Subsections showed $I_c$ scattering corresponding to damaged areas of the CC tape revealed that transverse cracks were distributed throughout the gauge length. This homogeneous $I_c$ degradation behaviour under tension is similar with the case under torsion strain but different with the case under hard bending which were previously reported. This behaviour is also different with the case using Bi-2223 HTS tapes under tension strain.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1999년도 추계학술대회 논문집 - 한국공작기계학회
• /
• pp.339-344
• /
• 1999

For the Tailor Welded Blank sheet used for automobile body panel, the characteristics of fatigue strength and crack propagation behavior were studied. The thickness of specimen was machined to be same (0.9mm+0.9mm) and different (0.9mm+2.0mm). As a base test, mechanical properties around welding zone were examined. The results indicated that there were no significant decreases in mechanical properties, but hardness around welding bead is 2.3 times greater than base material. The fatigue strength was the highest when the loading direction was parallel to the welding direction, which was about 85% of tensile strength of base material. It was decreased by 8.5% when the thickness of specimen and base material was different, and it is increased by 25% when pre-strain was applied. The crack propagation rate was noticeable decreased around welding line and rapidly increased as it passed by welding line. Reviewing the shape of the crack propagation, crack width around welding line was wide around the welding zone due to retardation of crack growth, but it became narrow passing welding line due to decreased toughness.

• 한국자동차공학회논문집
• /
• 제18권2호
• /
• pp.56-60
• /
• 2010

Since the forming process involves the strain rate effect, a yield function considering the strain rate is indispensible to predict the accurate final blank shape in the forming simulation. One of the most widely used in the forming analysis is the Hill48 quadratic yield function due to its simplicity and low computing cost. In this paper, static and dynamic uni-axial tensile tests according to the loading direction have been carried out in order to measure the yield stress and the r-value. Based on the measured results, the Hill48 yield loci have been constructed, and their performance to describe the plastic anisotropy has been quantitatively evaluated. The Hill48 quadratic yield function has been modified using convex combination in order to achieve accurate approximation of anisotropy at the rolling and transverse direction.

• 한국해양공학회지
• /
• 제4권1호
• /
• pp.110-119
• /
• 1990

This study is concerned about the stress concentration factor measurement by photoelastic method, for the case of two circular holes arrangement in 3mm semi-infinite plate under tensile load, the ratio of those two circular holes diameter, the ratio of distance apart from circular holes to breadth and the two holes arrangement angle with loading direction were varied. Besides, the measured stress concentration by photoelastic method around one circular hole was compared with that by strain-gage method.

• 소성∙가공
• /
• 제20권8호
• /
• pp.595-600
• /
• 2011

This paper investigates the effect of strain rate on the anisotropic deformation behavior of advanced high strength steel sheets. Uniaxial tensile tests were carried out on TRIP590 and DP780 steel sheets at strain rates ranging from 0.001/sec to 100/sec to determine yield stresses and r-values at various loading angles from the reference rolling direction. R-values were determined by the digital image correlation technique. Hill48 and Yld2000-2d yield functions were tested for their capability to describe the plastic deformation anisotropy of the materials. Initial yield loci were constructed using the Yld2000-2d yield function, which adequately described the anisotropic behavior of the materials. The shape of the initial yield loci was found to change with different strain rate, and the anisotropic behavior decreased with increasing strain rate.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 춘계학술대회 논문집
• /
• pp.263-265
• /
• 2009

In this study, ultrafine grained (UFG) oxygen free high conductivity copper (OFHC Cu) having two different grain morphologies, one the severely elongated and the other the equiaxed, was prepared by equal channel angular pressing (ECAP) with routes A and $B_c$, respectively. The results of quasi-static tensile tests at $10^{-1}\;s^{-1}$ and $1\;s^{-1}$ and dynamic compression tests at $10^3\;s^{-1}$ order revealed that the equiaxed UFG Cu exhibited higher strength and less ductility compared to the elongated one. The difference of the plastic flow characteristics between the two were rationalized by considering their dislocation mean free length based on the orientation relationship between the possible slip planes and the loading direction.

• 한국정밀공학회지
• /
• 제11권1호
• /
• pp.114-122
• /
• 1994

ESPE(Electonic-Speckle-Pattern-Interferometry) is very useful method for measuring In-plane displacement. Using the CW-Laser and Image processing system, it is possible to measure displacement and strain. Unlike traditional straingauge or moire' method, ESPI method requires no special surface preparation or attachments and can be measured In-plane displacement with no contact and real time. In this experimental specimen was loaded in paralled with loadcell, which provided loading step. The specimen was sheet plate, which was attached straingauge in x-y direction. In this study provides an example of how ESPI has been used to measure two dimensional displacement and strain distribution in this specimen. The results measured by ESPI compare with the data which was measured straingauge method in tensile testing at 1 ton range.

• 한국강구조학회 논문집
• /
• 제21권5호
• /
• pp.527-536
• /
• 2009

본 연구의 목적은 박판 탄소강 일면전단 2행 2열 볼트접합부의 블록전단파단거동과 면외변형의 영향을 조사하는 것이다. 하중직각 방향 연단거리, 볼트직경, 피치, 게이지 치수를 고정하고 블록전단파단이 발생하도록 실험체를 계획한다. 접합평판의 두께, 하중방향연단거리를 주요변수로 설정한다. 단순인장 실험을 실시하고 블록전단파단 양상, 최대내력을 현행의 설계기준식에 의한 예측치와 비교한다. 또한, 판 두께와 연단거리에 따른 하중방향과 직각방향으로 발생하는 면외변형의 발생조건을 조사하고 면외변형의 발생으로 인한 내력저하정도를 고찰한다.

• 한국강구조학회 논문집
• /
• 제15권5호통권66호
• /
• pp.509-518
• /
• 2003

본 논문에서는 강 콘크리트 경계면에 대한 비선형 해석 모델을 바탕으로 합성 구조체에 대한 비선형 구조해석을 실시하여 강 콘크리트 경계면을 모사한 인터페이스 요소에 발생하는 접선응력선 상대슬립 분포 등 합성 구조체의 경계면 거동 특성을 해석적으로 규명하였다. 연구결과 본 논문의 해석 모델인 합성 바닥판에서는 T형강-콘크리트 경계면 보다는 하부강판-콘크리트 경계면에서 접선응력의 증가가 빠르게 나타났으며, 하부강판-콘크리트 경계면에서도 인장부보다는 중립부 경계면에서 접선응력의 증가가 빠르게 진행되었다. 횡방향으로는 하중재하 위치에서 외부 측면으로 갈수록 접선응력이 완화되는 현상을 나타내었으며 종방향으로는 중앙부에서 최소, 지지점에서 $0.6{\sim}0.7L$ 지점에서 최대를 나타냈으며 이후 지지점으로 갈수록 감소하는 경향을 나타내었고, 하층이 증가하면서 경계면의 파괴가 최고 접선응력지점에서 전체영역으로 점차 확대되는 경향을 나타내었다. 이상의 연구결과는 합성 구조체의 경계면의 거동 특성과 하중전달 메카니즘을 이해하고 합리적인 전단연결재 설계를 위한 바탕을 제공할 것으로 기대된다.