• 한국응용과학기술학회지
• /
• 제35권4호
• /
• pp.1307-1319
• /
• 2018

대기오염에 대한 관심이 증대하면서 대기오염물질의 저감에 관한 많은 연구가 진행되고 있다. 차량용 요소수(Urea solution)를 이용한 디젤 차량의 질소산화물(NOx) 제거는 큰 효과를 나타내고 있다. 요소수의 품질은 국내법으로 엄격히 규정하고 있으나 요소수 내 불순물의 증대는 질소산화물 저감 효과를 감소시키게 된다. 따라서 본 연구에서는 일정 온도와 시간동안 요소수를 가열한 후 요소수의 물성변화를 분석하였다. 또한, 요소수를 보관하는 저장용기와 저장온도의 변화에 따른 요소수 물성변화도 함께 분석하였다. 요소수를 일정시간 가열한 후 요소수 내 뷰렛함량은 증가하고 요소함량은 감소하였으며, 요소함량감소에 따라 밀도와 굴절률도 함께 감소하였다. 철제 및 PET 용기와 일정온도($30^{\circ}C$, $50^{\circ}C$)에서 실시한 저장안정성 시험에서는 물성변화가 나타나지 않았다.

• Journal of the Korean Wood Science and Technology
• /
• 제51권6호
• /
• pp.431-446
• /
• 2023

Samama wood (Anthocephalus macrophyllus (Roxb) Havil) is a fast-growing and lesser-utilized wood species that has inferior properties; therefore, its quality needs to be improved. This research aimed to determine the effect of citric acid impregnation at high curing temperatures on the dimensional stability and mechanical properties of wood. Citric acid solution with 10% concentration (w/w) was impregnated into wood samples by vacuum-pressure method (-0.5 cmHg, 30 min; 0.7 MPa, 3 h), followed by curing process at 140℃, 160℃, and 180℃ of temperature for 1 h. In comparison, the other wood samples were heat treated at the same temperatures and time. The results showed that the increase in curing and heat temperatures for both treatments were directly proportional to the dimensional stability, but inversely proportional to the mechanical properties. Citric acid impregnated had higher density, dimensional stability, and mechanical properties, except for modulus of rupture, than that of heat treatment. The optimum temperature is suggested at 160℃ in both treatments.

• 한국정밀공학회지
• /
• 제34권3호
• /
• pp.161-166
• /
• 2017

Inconel 718, a typical ultraheat-resistant alloy, is recognized as a useful component in aircraft parts owing to its high-temperature strength and good chemical stability. Although many studies have been conducted to determine the proper drill shape to overcome the poor machinability when drilling into Inconel 718, most have involved a cutting process program known as AdvantEdge, as an experimental approach requires much time and money. In this study, our purpose is to optimize the drill shape for efficient drilling by conducting a trust force and temperature analysis using AdvantEdge. In order to achieve this purpose, the reliability of the results of the analysis was verified and by applying design of experiment an analysis of the geometric parameters of the drill shape considering the thrust force and temperature was conducted.

• 동력기계공학회지
• /
• 제8권3호
• /
• pp.36-43
• /
• 2004

The effect of bath composition, plating condition and plating rate on the magnetic property of electroless Co-Cu-P deposits were investigated. With increasing $CuCl_2$ concentration in the bath, plating rate increased, while the Br value of deposit decreased sharply. Deposited surface were inferiority by the increase pH above 10.5, bath temperature higher than $80^{\circ}C$. Plating reaction had been ceased by the increase of pH above 11, bath temperature higher than $90^{\circ}C$ and under $40^{\circ}C$. The Br value of deposit was uniform with various concentration of complexing agent(sodium citrate) in the bath. The Br value of deposit was almost equal to that found by the addition of stabilizer (thiourea) and accelerator(NaF). The Br value of deposit was uniform in plating time(20min) and heat treatment temperature(below $200^{\circ}C$), and were confirmed to have adequate bath stability for practical use.

• 한국식품영양과학회지
• /
• 제23권5호
• /
• pp.856-862
• /
• 1994

In salt-preserved foods of every kinds, it was examined the growth condition of halophilic bacteria that induced a change of colour, taste, nutritive substance, a production condition of enzyme and a character of crude enzyme. Used bacteria is H. halobium a kind of extremely halophilic bacteria, and the required of optimum culture needed a quite long time of crude enzyme production is 168 hours. Optimum pH is about 7-7.5, so the traditional food of such neutrality pH as soybean paste and soy sauce particularly come into trouble because the growth can flourish in neutrality or alkaliescence, and the crude enzyme also appeared that best activation between pH 6 and pH 8. The optimum temperature is about 37$^{\circ}C$, the optimum temperature of enzyme is about 40 $^{\circ}C$ and the temperature stability is settled for 15 minutes and it is completely inactivated at 10 minutes. In the influence of each metal ion, Fe++ and Mn++ a stimulated the growth of H.halobium and the activation of enzyme, Cu++ and Zn++ were identified that made the growth and the activation of enzyme inhibit.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2003년도 추계학술대회 논문집
• /
• pp.146-151
• /
• 2003

Reduced Activation Ferritic/Martenstic (RAFs) are leading candidates for structural materials of D-T fusion reactor. One of The RAFs, JLF-1 (9Cr-2W-V, Ta) has been developed and proved to have good resistance against high-fluency neutrino irradiation and good phase stability. Recently, in order to clarify the strengthening mechanical at high temperature, a new scheme to improve high temperature mechanical properties is desired. Therefore, the creep properties and creep life prediction by Larson-Miller Parameter method for JLF-1 to be used for fusion reactor materials or other high temperature components were presented at the elevated temperatures of $500^{\circ}C$, $550^{\circ}C$, $600^{\circ}C$, $650^{\circ}C$ and $704^{\circ}C$. It was confirmed experimentally and quantitatively that a creep life predictive e벼ation at such various high temperatures was well derived by LMP.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집C
• /
• pp.525-530
• /
• 2001

As a part of efforts to examine feasibility of warm forging near-net-shape process for non-heat-treated steel to replace quenched and tempered S45C steel, the optimized process condition has been determined to be $820^{\circ}C$ for heating, 10/sec for strain rate of forging and approximately 250MPa for flow stress from observed results such as the $A_{3}$ transformation temperature of about $790^{\circ}C$, the fully dynamic recrystallized behavior between $800^{\circ}C\;and\;850^{\circ}C$ when compressed up to 63% engineering strain at 10/sec strain rate, and the high temperature microsturctural stability. Also, controlled cooling rate of $6.3^{\circ}C/sec$ by water-spraying at a rate of $0.10cc/sec-cm^{2}$ for 60seconds followed by air-cooling right after forging process has been considered in this study as a feasible approach based on examination of the microsturcture of mixed ${\alpha}-ferrite$ and pearlite, the hardness and tensile properties meeting specification, and the reduced total cooling time to room temperature. Successive works would be carried out for the impact strength, machinalility, and forgeability at this process in the near future.

• 대한기계학회논문집A
• /
• 제25권9호
• /
• pp.1416-1422
• /
• 2001

The objective of this work was to characterize mechanical properties of thermoplastic composites with various forming conditions in compression molding. Randomly oriented long glass fiber reinforced polypropylene(PP) was used in this work. The composite materials contained 20%, 30%, and 40% glass fiber by weight. Compression molding was conducted at various mold temperatures and charge sizes. The temperatures on the mold surface and at the material in the mid-plain were monitored during the molding. Differential Scanning Calorimeter was used to measure crystallinity at both in-side and out-side of the sheet material. Crystallinity at each temperature was also measured by X-ray diffractometer. Dimensional stability was studied at various conditions with the spring forward angle. Among the processing parameters, the crystallization time at the temperature above 130$^{\circ}C$, was found to be the most effective. Spring-forward angle was reduced and the tensile modulus was increased as the mold temperature increased.

• Journal of Pharmaceutical Investigation
• /
• 제21권3호
• /
• pp.161-170
• /
• 1991

The storage stabilities of immunoliposomes incorporated with variable amounts of ganglioside $G_{M1}$ were investigated as a function of time. temperature. and composition by observing absorbance of visible light and calcein release. In the column chromatographe, the layer of unsaturated PE(dioleoylphosphatidylethanolamine : DOPE). unable to form stable liposomes at physiological temperature and pH, were formed when palmitoyl-immunoglobulin G(IgG) $(2.5{\times}10^{-4}\;mol/DOPE\;mol)$ added. The incorporation of ganglioside $G_{M1}$ into immunoliposome. enhanced the stabilities of bilayers during the extended period of storage. The turbidities of immunoliposomes coated with ganglioside $G_{M1}$ exhibited the maximum near 20 mol% $G_{M1}/DOPE$ mol. probably because of the disturbance of the bilayer characteristics, i.e., layer transition or reorientation of interaction sites. At low temperature. the higher stability was achieved than at elevated temperatures. After one week of storage. the redispersed liposomal solutions at lower temperatures maintained the original elution patterns in chromatography but broader distribution at elevated temperatures. During the storage, it is suggested the aggregation is the more dominant phenomena for liposomes kept at $5^{\circ}C$ than the fusion. while he fusion is at elevated temperatures.

• 한국세라믹학회지
• /
• 제28권4호
• /
• pp.261-268
• /
• 1991

The dielectric properties and microstructure of SrTiO3-based grain boundary layer (GBL) capacitor were investigated, and SrTiO3 GBL capacitor was made by penetrating the Frit (PbO-Bi2O3-B2O3 system). The Nb2O5-doped SrTiO3 ceramics were fired for 4-hours, at 145$0^{\circ}C$ in H2-N2 atomsphere to get semiconductive ceramics. The grain size of SrTiO3 sintered at reduction atmosphere had increased as the amount of Nb2O5 increases and then decreased as the amount of Nb2O5 exceeded 0.2 mole%. Insulating reagents which contained PbO-Bi2O3-B2O3 system frit and oxide mixture were printed on the each semiconductive ceramics and fired at varying temperature and for different holding time. The optimum dielectric properties could be obtained by second heat treatment at 110$0^{\circ}C$ for 1 hour, when frit paste was printed. A SrTiO3-based GBLC had the apparent permitivity of about 3.2$\times$104, the dielectric loss of 0.01~0.02 and the stable temperature coefficient of capacitance. The influence of frit paste on dielectric properties was similiar to that of oxide paste but the stability of temperature property of capacitance was improved.