In order to study the feasibility of industrial application of Kimchi juice separation-pasteurization method, a pilot scale Kimchi pasteurizer was designed and fabricated. The apparatus consisted of five sections: Kimchi juice separation-mixing, holding, precooling and cooling sections. Stainless steel pipelengths required for the heat exchanging sections were determined based on an equation, $W{\;}C_p{\;}T{\;}={\;}U(2{\;}RL){\;}T_{1m}$. Overall heat transfer coefficients in preheating, holding, precooling and cooling sections were 875, 1398, 2036, and $288{\;}kcal/m^2h^{\circ}C$ at the flow rate of 4 l/min, respectively, and temperature profiles of each section were in good agreement with those predicted from design criteria. A preliminary test using Chinese radish Kimchi demonstrated that this method can effectively be used in commercial processing of kimchi.
Fluoronitriles-$CO_2$ gas mixtures are promising alternatives to $SF_6$ in environmentally-friendly gas-insulated transmission lines (GILs). Insulating gas heat transfer characteristics are of major significance for the current-carrying capacity design and operational state monitoring of GILs. In this paper, a three-dimensional calculation model was established for a GIL using the thermal-fluid coupled finite element method. The calculated results showed close agreement with experimentally measured data. The temperature distribution of a GIL filled with the Fluoronitriles-$CO_2$ mixture was obtained and compared with those of GILs filled with $CO_2$ and $SF_6$. Furthermore, the effects of the mixture ratio of the component gases and the gas pressure on the temperature rise and current-carrying capacity of the GIL were analyzed. Results indicated that the heat transfer performance of the Fluoronitriles-$CO_2$ gas mixture was better than that of $CO_2$ but worse than that of $SF_6$. When compared with $SF_6$, use of the Fluoronitriles-$CO_2$ gas mixture caused a reduction in the GIL's current-carrying capacity. In addition, increasing the Fluoronitriles gas component ratio or increasing the pressure of the insulating gas mixture could improve the heat dissipation and current-carrying capacity of the GIL. These research results can be used to design environmentally-friendly GILs containing Fluoronitriles-$CO_2$ gas mixtures.
Kim, Jae-Cheon;Kim, Jong-Kyung;Kim, Soon-Young;Kim, Yong-Kyun;Lee, Woo-Gyo
Journal of Radiation Protection and Research
/
v.29
no.4
/
pp.263-268
/
2004
Using the Monte Carlo simulation, a study on the lion-proportionality of the prototype phoswich detector with $2'{\times}2'$ CSI(Tl) and plastic scintillator, which was made by KAERI, has been carried. The defector response functions (DRFs) calculated by simulations were compared with the experimental measurement on the $^{137}Cs\;and\;^{60}Co$. To precisely simulate the DRF for the phoswich, the CSI(Tl) non-proportionality was calculated using the electron response and the simplified electron cascade sequence for treating the photoelectric absorption event. The resulting DRFs of $^{137}Cs\;and\;^{60}Co$ sources obtained by simulations were compared with experiments for verification. For $^{137}Cs$, gamma-ray responses simulated by MCNP5 are generally good agreement with the measured ones. But the DRF of $^{60}Co$ does not match well with the results of experiment in the energy region below second peak due to the coincidence effect of two gamma-rays (1.17 MeV and 1.33 MeV). Through the analysis of the non-proportionality of CsI(Tl) in the prototype phoswich, the improved DRFs considering non-proportionality were produced and the simulation results were verified using the experimental measurements. However, to more precisely reproduce the DRF for the phoswich, further studies in relation to the electron channeling effect and the Doppler broadening effect of a scintillator are still needed as well as considering that effect of the transfer contribution.
This study is meaningful in finding out what legal and policy issues need to be improved in order to foster the aircraft industry, which is relatively underdeveloped compared to the fact that some heavy industries, such as the automobile industry and shipbuilding industry, have achieved a high level of production and technology globally. Korea's aircraft industry has been growing at a slower pace than other industries, largely due to the country's economic growth and the lack of a market structure to properly use variables such as the level of development in related industries, aircraft technology and demand for aircraft manufacturing. While most industries are privately led by the market structure of the competition system, heavy industries such as the aircraft industry generally grow under the market structure of the incomplete competition system, because only by securing huge initial investment costs, high technology, and sufficient demand, they can maintain minimum economic feasibility. The Korean aircraft industry was focused on developing and mass-producing military aircraft focusing on military demand, but it sought to turn the tide by signing the BASA (Bileral Aviation Safety Agreement) with the U.S. A preliminary feasibility study was conducted in 2010 to develop next-generation medium-sized aircraft, but was cancelled due to differences in position with Canada's Bombardier, which is subject to the concourse, and Korea Aerospace Industries (KAI) is pushing for the production of Bombardier's Q400 license on its own. Compared to the mid-to-large sized civil aircraft that are facing difficulties in development, KAI and KARI are successfully developing technologies to unmanned aerial vehicles and civil helicopters. In addition, the unmanned aerial vehicle sector is not yet suitable for manufacturers that have an exclusive global influence, so we believe that it is necessary to pursue government-led research and development projects with a focus on the areas of commercial helicopters and unmanned aerial vehicles in order to foster the aircraft industry in the future. In addition, since military aircraft such as KT-1 and T-50 are currently being exported smoothly, and it cannot be overlooked that the biggest demand for aircraft manufacturing in the Korea is the military, it is necessary to push forward national R&D projects and defense R&D program simultaneously to enable both civilian-military development. However, there are many differences between the two projects in the way they are implemented, the department in charge and the royalty system. Through this study, we learned about the technology ownership and implementation rights of national R&D projects and defense R&D programs, as well as the royalty system. In addition, problems with the system were identified and improvement measures were derived.
Jung-Wook Park;Chan-Hee Park;Li Zhuang;Jeoung Seok Yoon;Changlun Sun;Changsoo Lee
Tunnel and Underground Space
/
v.33
no.3
/
pp.189-207
/
2023
In the present study, the thermoshearing experiment on a rough rock fracture were modeled using a three-dimensional grain-based distinct element model (GBDEM). The experiment was conducted by the Korea Institute of Construction Technology to investigate the progressive shear failure of fracture under the influence of thermal stress in a critical stress state. The numerical model employs an assembly of multiple polyhedral grains and their interfaces to represent the rock sample, and calculates the coupled thermo-mechanical behavior of the grains (blocks) and the interfaces (contacts) using 3DEC, a DEM code. The primary focus was on simulating the temperature evolution, generation of thermal stress, and shear and normal displacements of the fracture. Two fracture models, namely the mated fracture model and the unmated fracture model, were constructed based on the degree of surface matedness, and their respective behaviors were compared and analyzed. By leveraging the advantage of the DEM, the contact area between the fracture surfaces was continuously monitored during the simulation, enabling an examination of its influence on shear behavior. The numerical results demonstrated distinct differences depending on the degree of the surface matedness at the initial stage. In the mated fracture model, where the surfaces were in almost full contact, the characteristic stages of peak stress and residual stress commonly observed in shear behavior of natural rock joints were reasonably replicated, despite exhibiting discrepancies with the experimental results. The analysis of contact area variation over time confirmed that our numerical model effectively simulated the abrupt normal dilation and shear slip, stress softening phenomenon, and transition to the residual state that occur during the peak stress stage. The unmated fracture model, which closely resembled the experimental specimen, showed qualitative agreement with the experimental observations, including heat transfer characteristics, the progressive shear failure process induced by heating, and the increase in thermal stress. However, there were some mismatches between the numerical and experimental results regarding the onset of fracture slip and the magnitudes of fracture stress and displacement. This research was conducted as part of DECOVALEX-2023 Task G, and we expect the numerical model to be enhanced through continued collaboration with other research teams and validated in further studies.
The technique of information-communication rapidly developed has made it possible for us to do business through Internet. Electronic commerce was increased rapidly by the explosive development of the inter and communication revolution. E-Commerce has created a fundamentally new way of conduction and will change drastically accepted ways of doing business. Normally international trade has been formulated in a way that exporters and importers meet face-to-face and contract and pay by letter of credits. For the global electronic commerce to vitalized, the outstanding matters should encourage the creation of infrastructure of information security and new models in the field of electronic payment systems, electronic commerce agreement for remedy, adapting electronic date interchange in transport documents and negotiability of electronic bills of lading. The payment systems such as electronic fund transfers, tradecard system and electronic letters of credits issued by SWIFT system permit the parties concerned(sellers, buyers ad service providers) to settle payment electronically. Still they are many limitations for complete international electronic transactions. The following measures have to be taken to vitalize electronic trade transactions. It is needed to acquire information security such as authenticity, integrity, non-repudiation and confidentiality. All kinds of documents need to be replaced by electronic date exchange and the legal structure of international convention, national law for electronic payment systems have to be completed. Also a detailed guide of the banking operation and developing rules for electronic letters of credits need to be provided to adopt eUCP rules for the electronic presentation of documents.
To develop simple and accurate analytical method for freezing time prediction of beef and tylose under various freezing conditions, freezing time (Y) was regressed against the reciprocal $(X_3)$ of difference of initial freezing point and freezing medium temperature, reciprocal $(X_4)$ of surface heat transfer coefficient, the initial temperature $(X_1)$ and thickness $(X_2)$ of samples which should cover most situations arising in frozen food industry. As results of the multiple regression analysis, equations were obtained as follows. $Y_{tylose}=3.45X_1+7642.84X_2+4642.67X_3+2946.89X_4-431.33\;(R^2=0.9568)$ and $Y_{beef}=0.68X_1+7568.98X_2+2430.78X_3+3293.26X_4-299.00\;(R^2=0.9897)$. These equations offered better results than Plank, Nagaoka and Pham's models, shown in satisfactory agreement with models of Cleland & Earle and Hung & Thompson when were compared to previous models, and the accuracy of its was very high as average absolute difference of about 10% in the difference between the fitted and experimental results. Also, thermal diffusivities of beef and tylose were measured as $4.43{\times}10^{-4}m^2/hr$ and $4.39{\times}10^{-4}m^2/hr$ at $6{\sim}7^{\circ}C$, $2.42{\times}10^{-3}m^2/hr$ and $3.32{\times}10^{-3}m^2/hr$ at $-10{\sim}-12^{\circ}C$. Initial freezing points of beef and tylose were $-1.2^{\circ}C\;and\;-0.6^{\circ}C$, respectively. Surface heat transfer coefficients were estimated $20.57\;W/m^2^{\circ}C$ with no-packing, $16.11\;W/m^2^{\circ}C$ with wrap packing and $13.07\;W/m^2^{\circ}C$ with Al-foil packing, and the cooling rate of immersion freezing method was about 10 times faster than that of air blast freezing method.
A cross-sectional study was undertaken to report prevalence and to identify risk factors of subclinical mastitis of dairy cattle in Sylhet district of Bangladesh. Among 325 dairy farms of the district 12 farms(3.7%) were selected conveniently for this study. All the dairy cows of the 12 farms were selected for sample collection. Fresh milk samples from each of the selected dairy cows were collected aseptically in separate sterilized test tube as RF, RH, LF and LH quarter of the udder. Rapid modified White Side Test(WST) was used to detect subclinical mastitis(SCM). Results of WST and data derived from filled in questionnaire were entered in Microsoft Excel 2003 and transferred to $STATA^{(R)}$, version 8.0/Intercooled(Stata Corporation, Texas, USA, 2003). The overall prevalence of SCM and its distribution in different categories of variables in cow and their exact binomial 95% confidence intervals were calculated in $STATA^{(R)}$. Simple bivariable associations among independent variables were investigated by $x^2$ test in $STATA^{(R)}$. Multiple logistic regression analysis with backward elimination method was used to identify risk factors of SCM. To identify significant variation in quarter SCM, linear regression analysis was performed after arcsine transformation of the data. The overall prevalence of SCM found in this study is 54%. Dairy cows with teat lesions had significantly increased SCM(OR=12342, P value=0.000, 95% CI=762, 199798) than others without teat lesions. The Holstein Friesian X Jersey X Sahiwal breed has significantly decreased(OR=0.18, p=0.03, 95% CI 0.04, 0.85) SCM than other breeds. The prevalence of SCM found in this study is in agreement with others. The injury in the teat increases the probability of getting infected with microbes and thereby mastitis. If the prevalence of teat lesion can be decreased the probability of subclinical mastitis will also be decreased. The negatively associated Holstein Friesian X Jersey X Sahiwall breed may help in planning mastitis control program if this finding can be validated by a more powerful case-control or cohort study design.
Software license agreements, to be useful in the mass market, could not be individually negotiated, and had to be standardized and concise. The software license agreement needs to be presented to the licensee-users in a fashion that would allow for mass distribution of software, also for it to enforceable, that would draw the users' attention to the terms and conditions under which the publisher allowed the use of the software. These needs have been accomplished, with or without fail, through so called the "shrink-wrap licenses" Shrink-wrap licenses purpose to transfer computer softwares to their users by defining the terms and conditions of use of the software without implicating the "first sale doctrine" of the Copyright Act. These shrink-wrap licenses have become essential to the software industry. However, in USA, the law applicable to these licenses has been unclear and unsettled. Courts have struggled to develop a coherent framework governing their enforceability. Meanwhile, the National Conference of Commissioners on Uniform State Laws ("NCCUSL") in USA promulgated the Uniform Computer Information Transaction Act ("UCITA") governing contracts for computer information transaction on July 29, 1999. One clear objective of UCITA was to settle the law governing the enforceability of shrink-wrap licenses. In these respects, this paper first introduces the various forms that shrink-wrap licenses take(at Part II. Section 1.), and explains the main advantages of them(at Part II. Section 2.) Here it shows how shrink-wrap licenses value themselves for both software publishers and users, including that shrink-wrap licenses are a valuable contracting tool because they provide vital information and rights to software users and because they permit the contracting flexibility that is essential for today's software products. Next, this paper describes the current legal framework applicable to shrink-wrap licenses in USA(at Part III). Here it shows that in USA the development of case law governing shrink-wrap licenses occurred in two distinct stages. At first stage, judicial hostility toward shrink-wrap licenses marked such that they were not enforced pursuant to Article 2 of the Uniform Commercial Code. At second stage, courts began to recognize the pervasiveness of shrink-wrap licenses, their indispensability to the rapidly expanding information technology industry, and the urgent need to enforce such licenses in order to maintain low prices for consumers of computer hardware or software, resulting in the recognition of shrink-wrap licenses. Finally, in view of the importance of UCITA, this paper examines how it will affect the enforceability of shrink-wrap licenses(at Part IV). The drafters of UCITA, as well as the scholars and practitioners who have criticized it, agree that it validates shrink-wrap licenses, provided certain procedural protections are afforded to purchasers. These procedural protections include the licensee end-user must (i) manifest his assent to the shrink-wrap license, (ii) have an opportunity to review the shrink-wrap license, (iii) have a right to return the product without costs.
EDI (Electronic Data Interchange) has been widely utilized to support Business Activities since it has such advantages as fast transfer of information, less documentation work, efficient information exchange etc. Recently e-business environment has urged the traditional EDI system to be changed to ebXML framework. To apply the ebXML framework to a certain industry, it is required to implement Business Process (BP), Core Component (CC), Collaboration Protocol Profile (CPP), Collaboration Protocol Agreement (CPA), Messaging system etc. We have selected the port and logistics industry as a target domain to apply ebXML framework, since the EDI usage ratio of it is relatively higher than other industries. In this paper, we have analyzed the current status of EDI system and transaction processes in the port and logistics industry. We have defined the business process that will be registered in the registry/repository, the main component of ebXML framework, using UN/CEFACT modeling methodology. And Business Collaborations, Business Transactions, Business Document Flows, Choreography, Pattern, etc. are represented using UML according to UN/ CEFACT modeling methodology, to apply ebXML Framework to the port and logistics distribution industry. Also we have suggested the meta methodology for applying the ebXML framework to other industries.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.