• Journal of the Korean Wood Science and Technology
• /
• v.10 no.3
• /
• pp.46-47
• /
• 1982

1. The physical and anatomical properties investigated in this study are the ones, which may give more effect on absorption of preservatives, such as variation of annual ring, specific gravity, shrinkage, E.M.C. of desorption and adsorption at 70 percent relative humidity condition, general and minute properties of wood. 2. On this study, the positive effects of wood structure, in particular, the appearances of tyloses in vessel element upon the absorption of creosote were observed. 3. Thirteen percent sodium chloride solution treatment and boiling hot water treatment have shown poor results to improve the preservative absorption characteristics of tested species however, some slight difference between treated and control could be seen. (see Tables 6 and 7).

• Journal of Korean Society of Water and Wastewater
• /
• v.10 no.1
• /
• pp.69-77
• /
• 1996

To evaluate the change of the groundwater flow and the water table response resulting from urbanization, two cases of the transient three-dimensional numerical simulations were performed. Variations of the groundwater flow system caused by withdrawals were analyzed. Two cases of infiltration rates were applied in this study to verify the water table changes. One is the rate under the circumstance during 1994 and the other is the revised rate. The numerical results from this study indicated that groundwater flow was influenced by human impacts. Groundwater flow has been concentrated to Taegu Textile Complex area where had large amount of pumping. Water table so far decreased -2.76m a year due to withdrawals. Water tables of many points were increased more than 30cm when the surface was reformed by infiltrating the rainfall. It was appeared that the improvement of surface to recharge the precipitation was very important to preserve and manage for the groundwater.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.11a
• /
• pp.903-908
• /
• 2006

As environmental vibration requirements on precision equipment become more stringent. use of pneumatic isolators has become more popular and their performance is subsequently required to be further improved. Dynamic performance of passive pneumatic isolators is related to various design parameters in a complicated manner and, hence, is very limited especially in low frequency range by volume of chambers. In this study, an active control technique, so called time delay control which is considered to be adequate for a low frequency or nonlinear system, is applied to a single chamber pneumatic isolator. The procedure of applying the time delay control law to the pneumatic isolator is presented and its effectiveness in enhancement of transmissibility performance is shown based on simulation and experiment. Comparison between passive and active pneumatic isolators is also presented.

• Journal of Institute of Control, Robotics and Systems
• /
• v.16 no.9
• /
• pp.872-875
• /
• 2010

This paper describes new harmonic disturbance compensation based on a peak filter array for Hard Disk Drives. Unlike a conventional method, the proposed method does not require any sin/cos functions or tables and reduces effects of all harmonic disturbances within a nyquist frequency. Two factors are introduced to parameterize stability and a gain tune. In addition, it is verified that the order of the proposed filter is minimal. From 600 experimental results, 8.5% performance improvement is achieved.

• Proceedings of the KIEE Conference
• /
• 1991.07a
• /
• pp.341-344
• /
• 1991

Rules in expert system have meaning of assigning never-happen-minterms. Overall logical relations of variables can be achived by making all prime implicants of never-happen-minterms. From prime implicants, two tables, which are necessary in the process of inference, are constructed. There are two inferencing modes. One excutes inference only one variable which the user is interested in, and the other excutes inference all variables simultaneously. Outputs of inference have not only 'true' or 'false' but also 'unknown' which is different from conventional expert system. In this paper, an efficient approach is presented, which can check logical inconsistency in knowledge base and contradiction between input facts and rules. The methods in the paper may be available in the field of diagnosis and alarm processing.

• The Journal of Information Technology and Database
• /
• v.3 no.2
• /
• pp.3-24
• /
• 1996

In this paper a data replicator scheme with a distributed join architecture is suggested with its cost functions and the performance results. The contribution of this scheme is not only minimizing the number of base relation locks in distributed database tables but also reducing the remote transmission amount remarkably, which will be able to embellish the distributed databse system practical. The differential files that are derived from the active log of the DBMS are mainly forcing the scheme to reduce the number of base relation locks. The amount of transportation between relevant sites could be curtailed by the tuple reduction procedures. Then we prescribe an algorithm of data replicator with its cost function and show the performance results compared with the semi-join scheme in their distributed environments.

• Industrial Engineering and Management Systems
• /
• v.10 no.2
• /
• pp.154-160
• /
• 2011

In this paper, a reliability sampling plan under progressively type-1 interval censoring is proposed when the lifetime of products follows the Pareto distribution of second kind. We use the maximum likelihood estimator for the median life and its asymptotic distribution. The cost model is proposed and the design parameters are determined such that the given producer's and the consumer's risks are satisfied. Tables are given and the results are explained with examples.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.6
• /
• pp.153-161
• /
• 2000

In controlling servomechanism, such as X-Y tables, friction is one of the most significant source of tracking error. Existing friction models work well when the direction of the motion does not change. However, when the direction of motion changes such as traversing a circular profile, relatively large tracking errors referred to as 'quadrant glitches' are introduced. In this paper, a new friction model, which has a term that can compensate the effect of the quadrant glitches, is proposed. The performance and effectiveness of the proposed model are evaluated through the experimental work. The results show that the controlling servomechanism with the proposed model completely remove the quadrant glitches.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.5
• /
• pp.72-80
• /
• 2002

DFA (Design for assembly) is a design philosophy for improving product designs for simpler or less costly assembly operations. This paper proposes a new DFA methodology that can estimate the standard assembly time and evaluate the assemblablity of parts. We select some determining and influencing factors related with assembly process, and estimate the assembly time using motion analysis. By the levels of the determining and influencing factors, the assemblability is evaluated, and finally, the tables that include the time and score of assembly is suggested.

• Journal of Korea Society of Industrial Information Systems
• /
• v.8 no.3
• /
• pp.91-98
• /
• 2003

Visitors who browse the web from wireless PDAs, cell phones are frequently frustrated by interfaces. Simply replacing graphics with text and reformatting tables does not solve this problem, because deep link structures can still require more time. To solve this problem, in the paper we propose an algorithm, Minimal Path Algorithm that automatically improves wireless web navigation by suggesting useful shortcut links in real time. In the result of this paper, Minimal Path algorithm offer the shortcut and the number of shortest links to web users.