• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.513-516
• /
• 2017

When stored for long periods in a powder-based device (PMD), the explosive power in the device is aged and the explosive power is changed. Thus, The gunpowder used in the PMD must be chemically and physically stable for both internal and external factors. Since $BKNO_3$ and THPP are used as representative gunpowder, thermodynamic and kinetic analyzes were performed based on these gunpowders. Differential scanning calorimeter (DSC) was used to analyze the calorific value and reaction rate. As a result, there was no significant change in caloric value and reaction rate in THPP. In addition, XPS and TEM-EDS analyzes were performed to confirm the formation of oxide films directly related to aging, and no oxide films were observed as a result of thermal analysis. In addition, XPS and TEM-EDS analyzes were performed to confirm the formation of oxide films directly related to aging. As a results, no oxide films were observed. It can be concluded that THPP is the most famous gunpowder in terms of long-term stability.

• Applied Microscopy
• /
• v.29 no.1
• /
• pp.75-81
• /
• 1999

Optimum conditions for making the Au and Al internal standards for TEM have been determined experimentally. The Au internal standard was produced by sputter coating at 9mA for 100 seconds in low vacuum $(\leq1\times10^{-3})$. The Al internal standard was produced by evaporation coating at 7kV for 10 minutes in high vacuum $(\leq1\times10^{-5})$. Measurements of the lattice parameters of andalusite and albite feldspars with this Au internal standard resulted in errors of (a) $ \leq1.2%$ in precion and $\leq0.3%$ in accuracy for andalusite: (b) $\leq0.5%$ in precision and $\leq1.1%$ in accuracy for albite feldspars. The most significant error occurred from the measuring processes of distances and angles of electron diffraction patterns. By employing systematic procedures of measurement with high precision devices, this lattice parameter determination method utilizing the internal standard should be a good alternative to the conventional powder XRD method or the sophisticated CBED method for special samples.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.23 no.3
• /
• pp.205-211
• /
• 2013

Objectives: 21 sepiolite substances produced in China were investigated for the presence of asbestos in their materials. Materials and methods: In order to identify asbestos in sepiolite substances, test materials were analyzed using a transmission electron microscope equipped with energy dispersive X-ray spectrometer (TEM-EDS) for confirming their shape and components (atomic %). Results: Five of 21 sepiolte substances were asbestos-containing materials. Two chrysotile containing sepiolite proved to be asbestoscontaining materials, as did two chrysotile mixed with tremolite containing sepiolite. 16 sepiolite substances did not contain asbestos materials. Conclusions: When importing sepiolite substances, they must be analyzed to determine if there is asbestos in their materials.

• Journal of the Korean Applied Science and Technology
• /
• v.33 no.3
• /
• pp.421-427
• /
• 2016

Nanosized hollow silica was prepared by $St{\ddot{o}}ber$ method in the presence of aluminum isopropoxide. The mixture of polyelectrolytes such as poly(sodium 4-styrene sulfonate)(PSS) and polyacrylic acid(PAA) were used as templates. Tetraethylorthosilicate(TEOS) and aluminum isopropoxide were used as precursors for silica and alumina, respectively. The function of aluminum isopropoxide is to increase the porosity of silica shell. The characterizations of hollow silica were examined by TEM(transmission electron microscopy), TGA(thermogravimetric analysis), BET(Brunauer Emmett Teller), Energy-dispersive X-ray spectroscopy(EDS), and FT-IR spectrum. It was found that the shell thickness of hollow silica was around 8 nm and the core diameter was around 20 nm by TEM.

• Journal of the Korean Ceramic Society
• /
• v.40 no.5
• /
• pp.460-467
• /
• 2003

Al-SiC$_{p}$ composite layer was prepared by plasma thermal spray on aluminum substrate using composite powder prepared by mechanical alloying. Mechanically alloyed powder was achieved after 24 h milling, which was used for thermal spray coating. The correlations between process conditions and thickness/porosity were analyzed, and increase of hardness was confirmed. The presence of Al-Si-C-O compound was detected by TEM analysis.

• Journal of the Korean Ceramic Society
• /
• v.26 no.5
• /
• pp.691-697
• /
• 1989

Fine TiO2 and BaTiO3 powders having spherical particles were synthesized by ultrasonic spray pyrolysis of alcoholic solution of metal alkoxide in an electric furnace heated at 400-90$0^{\circ}C$. Microstructure and composition of particles synthesized were observed by TEM and XRD respectively. Spectific surface area of powders synthesized was examined through BET specific surface area measurement. TEM observation revealed that the particle size did not change irrespective of pyrolysis temperature but decreased according to the increase of concentration and spherical particle was consisted of primary particles of about 0.02${\mu}{\textrm}{m}$. As for BaTiO3 powder, the ratio of Ti/Ba was 0.987 by EDX analysis.

• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.6 no.4
• /
• pp.11-19
• /
• 1995

In this paper, the Finite Difference Time Domain (FDTD) method is used to analyse the characteristics of the coaxial line transmission coefficent, shielding effectiveness, and compared to results of the moment method. The excitation mode of the Gaussian pulse is assumed to be a TEM-mode instead of the TE or TM-mode and in order to eliminate the reflected wave with in short length of the line. Calculated value of shielding effectiveness of the coaxial line by the FDTD are in good agreement with the results of the moment method.

• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.2 no.3
• /
• pp.3-9
• /
• 1991

Validity and limitation of conventional methods for analyzing the characteristics of nonuniform transmission lines are discussed here. It is found that uniqueness of cal- culated input impedance of an exponential transmission line by employing conventional methods is not assured in general but only under secific conditions. And the calculated input impedance of an angled two-plane transmission line based on the conventional planar TEM mode devices from its rigorous solution.

• Applied Microscopy
• /
• v.48 no.1
• /
• pp.1-5
• /
• 2018

Cryo-transmission electron microscopy (cryo-TEM) allows us to perform structural analysis of a analyses of large protein complexes, which are difficult to analyze using X-ray crystallography or nuclear magnetic resonance. The most common examples of proteins used are ribosomes and proteasomes. In this paper, we briefly describe the advantage of cryo-TEM and the process of two-dimensional classification by considering a human proteasome as an example.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.03a
• /
• pp.105-105
• /
• 2003

InGaN/GaN MQW 구조는 청색 및 녹색 범위의 밴드 갭을 가지는 반도체로 최근 LED 및 LD 제조 등에 이용되고 있다. InGaN/GaN MQW은 InGaN와 GaN의 최적 성장온도의 중간온도에서 실행된다. InGaN와 GaN는 최적 성장온도의 차이가 크므로 중간온도에서 성장 시에 많은 결함이 생긴다. 성장온도가 높으면 InN가 분해되고 낮을 경우에는 질소의 결핍이 일어난다. 최적성장온도의 선택이 매우 중요한 문제로 주목되었다. Si 도핑으로 중간온도 성장 시에 형성되는 결함을 감소시키고 광학적 특성을 향상시킨다고 보고되었다. 그러나, Si 도핑효과에 대한 구체적이고 체계적인 연구는 부족한 실정이다. MQWs 구조의 GaN 장벽층에 미치는 성장온도와 Si 도핑 효과를 이해하기 위해서는 고온에서 성잠시킨 GaN박막(HT-GaN) 위에 중간온도에서 성장된 GaN 에피층(IT-GaN)의 구조에 관한 연구가 선행되어야한다. 본 연구에서는 HT-GaN 위에 성장된 GaN 에피층에 미치는 성장 온도와 Si 도핑 효과에 관해 연구하였다.