• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.4
• /
• pp.629-635
• /
• 2009

The FSK duplex remote controlling wireless transmission units with a common local oscillator circuit for transmitter and receiver are designed and implemented in this paper. In the FSK full-duplex the channel frequency for Tx/Rx is allocated, a common switching oscillator circuit for Tx/Rx is designed in the FSK half-duplex scheme. Both of FSK units get functions of automatic channel detection for busy channels and channel configuration for an idle channel in order to reduce the RF channel interference and are designed as a remote controller with small-sized low power of 10mW and the 400MHz-colpitz type PLL configuration of 50kHz channel separation. The full-duplex Tx/Rx link frequency gets frequency difference of 42.8MHz, which is double of 21.4MHz IF frequency.

• Journal of Information Display
• /
• v.10 no.1
• /
• pp.33-36
• /
• 2009

A new hybrid silicon thin-film transistor (TFT) fabrication process using the DPSS laser crystallization technique was developed in this study to realize low-temperature poly-Si (LTPS) and a-Si:H TFTs on the same substrate as a backplane of the active-matrix liquid crystal flat-panel display (AMLCD). LTPS TFTs were integrated into the peripheral area of the activematrix LCD panel for the gate driver circuit, and a-Si:H TFTs were used as a switching device of the pixel electrode in the active area. The technology was developed based on the current a-Si:H TFT fabrication process in the bottom-gate, back-channel etch-type configuration. The ion-doping and activation processes, which are required in the conventional LTPS technology, were thus not introduced, and the field effect mobility values of $4\sim5cm^2/V{\cdot}s$ and $0.5cm^2/V{\cdot}s$ for the LTPS and a-Si:H TFTs, respectively, were obtained. The application of this technology was demonstrated on the 14.1" WXGA+(1440$\times$900) AMLCD panel, and a smaller area, lower power consumption, higher reliability, and lower photosensitivity were realized in the gate driver circuit that was fabricated in this process compared with the a-Si:H TFT gate driver integration circuit

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.36D no.11
• /
• pp.27-32
• /
• 1999

Metal-ferroelectric-semiconductor devices by susing rapid thermal annealed $LiNbO_3/Si$(100) structures were fabricated and demonstrated nonvolatile memory operations. The estimated field-effect electron mobility and transconductance on a linear region of the fabricated FET were about $600cm^2/V{\cdot}s$ and 0.16mS/mm, respectively. The ID-VG characteristics of MFSFET's showed a hysteresis loop due to the ferroelectric nature of the $LiNbO_3 films. The drain current of the on state was more than 4 orders of magnitude larger than the off state current at the same read gate voltage of 0.5V, which means the memory operation of the MFSFET. A write voltage as low as ${\pm}3V$, which is applicable to low power integrated circuits, was used for polarization reversal. The ferroelectric capacitors showed no polarization degradation up to $10^{10}$ switching cycles with the application of symmetric bipolar voltage pulse (peak-to-peak 6V, 50% duty cycle) of 500kHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.3
• /
• pp.384-390
• /
• 2008

Chaotic OOK modulation method can be used in LDR(Low Data Rate) UWB systems. In this paper, UWB chaotic-OOK transmitter system is designed and verified using TSMC 0.18 um CMOS process. A transmitter system is composed of Quasi-chaotic signal generator, OOK Modulator, and driving amplifier. The traditional chaotic signal generators using analog feedback method is weak to process variation. In order to solve this problem, a quasi-chaotic signal generator using digital feedback technique is get wide band signal and OOK Modulator using T-type switching structure is used to enhance the isolation characteristic. A driving amplifier has differential to single structure to avoid an external balun for low cost communication. The measured output power spectrum of the transmitter meet the FCC regulation and the result of the modulation test at data rate of 20 Kbps, 200 Kbps, 2 Mbps, and 10 Mbps is conformed to LDR UWB system. It is shown that the transmitter in this paper can be used for the UWB chaotic-OOK system.

• Journal of Advanced Marine Engineering and Technology
• /
• v.34 no.2
• /
• pp.332-338
• /
• 2010

Annually, electrical fires caused by arcing phenomena in power system rapidly increase as the use of more electric appliances, but there is no established method for the prevention of the accidents. With this background, this paper dealt with the experimental results on a series arc detection technique and a device for air conditioners. Series arcing phenomena that is generated in incomplete connection of air conditioners was simulated, and the frequency spectrum was analyzed. The Fast Fourier Transform (FFT) of the arc pulse showed that the dominant frequency components exist in ranges of 190 kHz~250 kHz and 900 kHz~1.6 MHz. An arc detection circuit with low cut off frequency of 170 kHz to attenuate 60 Hz by 170 dB and a signal discriminator were designed. Also, an algorithm which separate series arc signal from unwanted noises produced by switching operation, inverter, and surge was proposed. Application experiment was carried out on several types of air-conditioners by using the arc generator specified in UL1699, and the results showed the over 99 % accuracy.

• Fire Science and Engineering
• /
• v.20 no.1 s.61
• /
• pp.71-76
• /
• 2006

The major causes of electrical fire are classified to short circuit fault, overload fault, electric leakage and electric contact failure. The occurrence factor of the fire is electric arc or spark accompanied with electrical faults. Residual Current Protective Device(RCD) of high sensitivity type used at low voltage wiring cuts off earth leakage and overload, but the RCD can't cut off electric arc or spark to be a major factor of electrical fire. As the RCDs which are applied low voltage distribution panel are prescribed to rated breaking time about 30[ms](KS C 4613), the RCDs can't perceive to the periodic electric arc or spark of more short wavelength level. To be improved on such problem, this paper is proposed to a auxiliary control apparatus for RCD trip on electric arc or spark due to electrical fire. Some experimental results of the proposed apparatus is confirmed to the validity of the analytical results.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.18 no.5
• /
• pp.475-480
• /
• 2012

This study on the methode is easied to distinguish with emotional visual lighting on AtoN facility using 3colors LED, and which is controlled to on-off switching of approach light in shore or harbor. The identification have easied to provide a differentiation between the AtoN facility of red and white light and surrounding light in harbor both sides. And the integrated controller have designed to left-right and serial sequential lighting system for harbor guidance using the GPS synchronous or timer. There is expectation effect that is prevent a confusion about distinguish of facility by ship's operator and to beautify a night scene of harbor, which is expressed to emotional identification lighting and variable color lighting on AtoN body by vertical layer color lighting using LED. In addition, the performance of AtoN is implemented to display with guidance light the harbor safety message by morse code lighting. Effectiveness of system is enhanced that age and power consumption reduce by candle alternated high light LED.

• Journal of Industrial Technology
• /
• v.40 no.1
• /
• pp.13-18
• /
• 2020

Lithium-ion batteries have a small volume, light weight and high energy density, maximizing the utilization of mobile devices. It is widely used for various purposes such as electric bicycles and scooters (e-Mobility), mass energy storage (ESS), and electric and hybrid vehicles. To date, lithium-ion batteries have grown to focus on increasing energy density and reducing production costs in line with the required capacity. However, the research and development level of lithium-ion batteries seems to have reached the limit in terms of energy density. In addition, the charging time is an important factor for using lithium-ion batteries. Therefore, it was urgent to develop a high-speed charger to shorten the charging time. In this thesis, a discharger was fabricated to evaluate the capacity and characteristics of Li-ion battery pack which can be used for e-mobility. To achieve this, a smart discharger is designed with a combination of active load, current sensor, and temperature sensor. To carry out this thesis, an active load switching using sensor control circuit, signal processing circuit, and FET was designed and manufactured as hardware with the characteristics of active discharger. And as software for controlling the hardware of the active discharger, a Raspberry Pi control device and a touch screen program were designed. The developed discharger is designed to change the 600W capacity battery in the form of active load.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.12
• /
• pp.80-86
• /
• 2009

In this paper, we present a new charge pump circuit feasible for the implementation with standard twin-well CMOS process technology. The proposed charge pump employs PMOS-switching dual charge-transfer paths and a simple two-phase clock. Since charge transfer switches are fully turned on during each half of clock cycle, they transfer charges completely from the present stage to the next stage without suffering threshold voltage drop. During one clock cycle, the pump transfers charges twice through two pumping paths which are operating alternately. The performance comparison by simulations and measurements demonstrates that the proposed charge pump exhibits the higher output voltage, the larger output current and a better power efficiency over the traditional twin-well charge pumps.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.12
• /
• pp.58-65
• /
• 2009

In this paper, we designed high voltage gate drive IC including dead time circuit in which capacitors controlled rising time and falling time, and schimitt-triggers controlled switching voltage. Designed High voltage gate drive IC improves an efficiency of half-bridge converter by decreasing dead time variation against temperature and has variable dead time by the capacitor value. and its power dissipation, which is generated on high side part level shifter, has decreased 52 percent by short pulse generation circuit, and UVLO circuit is designed to prevent false-operation. We simulated by using Spectre of Cadence to verify the proposed circuit and fabricated in a 1.0um process.