• Structural Engineering and Mechanics
• /
• 제69권4호
• /
• pp.417-426
• /
• 2019

Buckling is one of the major causes of failure in thin-walled plate members and the presence of cracks with different lengths and locations in such structures may adversely affect this phenomenon. This study focuses on the buckling stability assessment of centrally and non-centrally cracked plates with small-, intermediate-, and large-size cracks, and different aspect ratios as well as support conditions, subjected to uniaxial compression. To this end, numerical models of the cracked plates were created through singular finite element method using a computational code developed in MATLAB. Eigen-buckling analyses were also performed to study the stability behavior of the plates. The numerical results and findings of this research demonstrate the effectiveness of the crack length and location on the buckling capacity of thin plates; however, the degree of efficacy of these parameters in plates with various aspect ratios and support conditions is found to be significantly different. Overall, careful consideration of the aspect ratio, support conditions, and crack parameters in buckling analysis of plates is crucial for efficient stability design and successful application of such thin-walled members.

• 문화기술의 융합
• /
• 제9권5호
• /
• pp.529-534
• /
• 2023

고속 및 대면적 인쇄를 위한 라인 프린팅 기술은 늘어난 헤드 길이만큼 헤드 내부로 잉크를 공급하는 유로를 확보해야 하는 구조적 취약점과 제조 과정에서 발생하는 잔류응력에 의한 피드홀 변형으로 인해 노즐층이 파손되거나 잉크가 누출되는 결함이 있다. 따라서 본 논문에서는 견고하고 신뢰할 수 있으며 라인 프린팅 방식에 보다 적합한 열전사 방식의 잉크젯 프린트 헤드 형상을 제안하고자 한다. 먼저 실험을 통해 초기 라인 프린팅 헤드의 변형량을 측정한 후 이를 등가의 하중량으로 변환하였으며 FEA 해석을 통해 하중 추정 방법의 타당성을 검증하였다. 또한 헤드 크기를 증가시키지 않으면서 변형을 최소화할 수 있도록 기둥이나 지지벽으로 단위 노즐을 보강하거나 지지빔이나 건/습식각된 브릿지를 추가하여 내부 강성을 증가시킨 헤드 구조를 설계하였으며, 피드홀 변형이 최대 90% 감소하는 것을 확인하였다. 제안된 형상 중 공정 편의성과 제작비용을 고려하여 건식각된 피드홀 브릿지 형태의 헤드를 선정하였으며 실제 제작을 통해 노즐층 변형이나 잉크 누출 없이 정상 작동하는 것을 확인하였다.

• 대한기계학회논문집B
• /
• 제24권5호
• /
• pp.632-639
• /
• 2000

Conjugate heat transfer from a heat generating module ($31{\times}31{\times}7mm^3$) bonded through the module support on the floor of a parallel-plate channel(20mm high, 400mm wide, and 800mm long) to mixed convective air flow(0.2${\sim}$0.9m/s) is studied experimentally. The input power to the module is changed in a range 1.0${\sim}$4.5W, the floor thickness 0.2${\sim}$5mm, and the thermal resistance of module support, Rc:=0.06, 1.03 and 82.0K/W. Thermal conductance(Uc) of the board and convective thermal conductance($U_A$) from the module were derived, and the effect of V; Rc and t on Uc was investigated. It is found that the conjugate conductance (Uc) and the conductive heat transfer ratio ($Q_B$/Q) depend on the thermal resistance of the module support, the air velocity and the board thickness. The change of the module support resistance and the board thickness helps to elucidate the relative significance of heat transfer paths through the module support, the board, and from the board surface to the air. Additional information is investigated about the dependence of the heat transfer rate on the mixed convection parameter.

• 한국강구조학회 논문집
• /
• 제18권5호
• /
• pp.563-574
• /
• 2006

본 연구에서는 개단면 리브를 갖는 보강판에 대하여 재하 크기가 보강판의 처짐에 미치는 영향을 살펴보고, 직교이방성 강성비를 매개변수로 하여 이를 정형화하고자 하였다. 재하 크기에 따른 보강판의 처짐 양상을 살펴보기 위하여, 집중하중과 3가지 크기의 등분포 하중을 판의 중앙에 위치한 리브 위에 작용시켜 해석하였다. 여러 가지 보강판에 대한 분석 결과, 집중하중에 대한 분포하중의 중앙점 처짐 비율은 재하 크기가 작을수록 크게 나타남을 알 수 있었으며, 이러한 처짐 비율은 리브 간격별로 강성비의 함수로 표현할 수 있음을 알 수 있었다. 또한, 분포하중 작용시 보강판의 최대 처짐은 국부 처짐의 발생으로 중앙점이 아닌 위치에서 발생하며, 중앙점 처짐에 대한 최대 처짐의 증가 비율은 리브 간격별로 강성비의 함수로 표현할 수 있음을 알 수 있었다. 본 연구에서 제안한 함수식을 직교이방성 판 해석에 적용한 결과 정확도의 향상을 나타내었으며, 또한 변장비 및 지지 조건이 다른 경우에 적용한 결과 타당한 결과를 나타내어, 본 연구에서 제안한 함수식을 이용하면, 직교이방성 판 해석시 간편하게 분포하중을 받는 보강판의 중앙점 처짐과 최대 처짐을 산정할 수 있을 것으로 판단된다.

• 한국지반신소재학회논문집
• /
• 제13권2호
• /
• pp.31-39
• /
• 2014

헬리컬 파일(helical pile)은 한 개 이상의 나선형 원판을 중공형 축에 부착한 후 지반에 회전 관입시켜 지지력을 발현하게 하는 말뚝기초의 하나이다. 헬리컬 파일은 나선형 원판이 부착된 철제 축과 나선형 원판이 모두 지지력을 발휘하기 때문에 기존의 말뚝 지지력 식으로 헬리컬 파일의 지지력을 예측하기 위해서는 검증이 필요하다. 본 연구에서는 중소구경 헬리컬 파일의 지지력을 확인하기 위하여 김포 일대에서 헬리컬 파일의 축의 직경과 원판의 형상, 관입 깊이를 변화시키며 시공한 후 재하시험을 수행하였다. 현장시험은 동일한 조건에서 헬리컬 파일 축의 직경을 73mm, 114mm 두 가지로 시공하여 지지력을 측정, 비교하여 축의 직경이 헬리컬 파일의 지지력에 미치는 영향을 검토하였다. 같은 방법으로 원판의 개수가 1개, 3개로 제작된 헬리컬 파일 및 원판의 직경을 400mm에서 250mm으로 변화시키며 시공한 헬리컬 파일의 재하시험 결과를 바탕으로 원판의 형상이 지지력에 미치는 영향을 분석하였다. 또한 헬리컬 파일의 관입 심도를 3m에서 6m까지 설정하여 관입 심도에 따른 지지력을 비교하였다. 현장 시험 결과 원판의 개수가 증가할수록, 원판과 축의 직경이 증가할수록 헬리컬 파일의 지지력이 증가하는 경향을 보이나, 축의 직경은 헬리컬 파일의 지지력에 상대적으로 적은 영향을 미치는 것을 확인할 수 있으며, 원판의 형상이 지지력에 미치는 영향이 상대적으로 큰 것으로 판단된다.

• Structural Engineering and Mechanics
• /
• 제28권1호
• /
• pp.53-67
• /
• 2008

Anisotropic materials are increasingly required in modern technological applications. Certainly, civil, mechanical and naval engineers frequently deal with the situation of analyzing the dynamical behaviour of structural elements being composed of such materials. For example, panels of anisotropic materials must sometimes support electromechanical engines, and besides, holes are performed in them for operational reasons e.g., conduits, ducts or electrical connections. This study is concerned with the natural frequencies and normal modes of vibration of rectangular anisotropic plates supported by different combinations of the classical boundary conditions: clamped, simply - supported and free, and with additional complexities such holes of free boundaries and attached concentrated masses. A variational approach (the well known Ritz method) is used, where the displacement amplitude is approximated by a set of beam functions in each coordinate direction corresponding to the sides of the rectangular plate. Consequently each coordinate function satisfies the essential boundary conditions at the outer edge of the plate. The influence of the position and magnitude of both hole and mass, on the natural frequencies and modal shapes of vibration are studied for a generic anisotropic material. The classical Ritz method with beam functions as spatial approximation proved to be a suitable procedure to solve a problem of such analytical complexity.

• 대한조선학회논문집
• /
• 제43권3호
• /
• pp.331-339
• /
• 2006

The objective of this paper is to calculate the fatigue strength for upper deck hatch corner insert plate of large container carriers without wave load analysis and global finite element analysis at the initial design stage. Wave load analysis and global F.E. analysis for three container carriers have been performed by GL(Germanischer Lloyd) procedure to propose the equation for hatch corner stress range which is the important factor in fatigue strength calculation. Considering the restraining effect of bulkhead, three types of equation, that is, single tight bulkhead, double tight bulkhead and support bulkhead have been proposed. Using the proposed equations, a simplified fatigue analysis based on GL rules has been performed for two container carriers of which fatigue strength analysis was carried out by GL. From the comparison between fatigue strength result of using the proposed equations and that of GL, it has been found that proposed stress range equations are useful for scantling of upper deck hatch corner insert plates for over 8,000 TEU class container carriers.

• 대한기계학회논문집B
• /
• 제30권8호
• /
• pp.772-779
• /
• 2006

Window is a critical component in the design of energy-efficient buildings. To minimize the heat loss, insulation performance of the glazing has to be improved. Manufacturing of vacuum glazing has been motivated by the possibility of making windows of very good thermal insulation properties for such applications. It is made by maintaining vacuum in the gap between two glass panes. Pillars are placed between them to withstand the atmospheric pressure. Edge covers are applied to reduce conduction through the edge. Accurate measurements have been made of the radiative heat transfer, the pillar conduction and the gas conduction using a guarded hot plate apparatus. Vacuum glazing is found to have low thermal conductance roughly below $1W/m^2K$. Among the heat transfer modes of residual gas conduction, conduction through support pillar and the radiative heat transfer between the glass panes, the last one is the most dominant to the overall thermal conductance. Vacuum glazing using very low emittance AI-coated glass has an overall thermal conductance of about $0.7W/m^2K$.

• Steel and Composite Structures
• /
• 제28권5호
• /
• pp.629-639
• /
• 2018

In this paper, the vibroacoustic responses of baffled laminated composite sandwich flat panel structure under the influence of harmonic excitation are studied numerically using a novel higher-order coupled finite-boundary element model. A numerical scheme for the vibrating plate has been developed in the frame work of the higher-order mid-plane kinematics and the eigen frequencies are obtained by employing suitable finite element steps. The acoustic responses are then computed by solving the Helmholtz wave equation using boundary element method coupled with the structural finite elements. The proposed scheme has been implemented via an own MATLAB base code to compute the desired responses. The validity of the present model is established from the conformance of the current natural frequencies and the radiated sound power with the available benchmark solutions. The model is further utilized to scrutinize the influence of core-to-face thickness ratio, modular ratio, lamination scheme and the support condition on the sound radiation characteristics of the vibrating sandwich flats panel. It can be concluded that the present scheme is not only accurate but also efficient and simple in providing solutions of the coupled vibroacoustic response of laminated composite sandwich plates.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• 제42권4호
• /
• pp.182-186
• /
• 2016

Objectives: The purpose of this study was to analyze the incidence of indications for the removal of mini-plates over a five-year period in maxillofacial trauma patients. Materials and Methods: The medical records of 530 patients who underwent treatment with mini-plate fixation after maxillofacial trauma were reviewed for a five-year period (May 2007 to May 2012). Patients were evaluated concerning the number of mini-plates removed, age and gender distributions, time between insertion and removal, indication for removal, and site of removal. Results: The plates of 120 patients were removed (26 females and 94 males). The removal rate was 22.6%. The most frequent indication for removal was patient demand (81.7%), followed by tooth extraction (7.5%), and pain (3.3%). The most frequent removal site was the mandible (95.0%). Conclusion: The number of mini-plates removed was small, and the most common indication for removal was patient demand. There is no evidence to support a recommendation for the routine removal of titanium mini-plates.