• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• 제12권6호
• /
• pp.445-452
• /
• 2002

The goal of this paper Is to characterize the vibration damping induced in a main structure by a large number of sub-oscillators. A simple expression is obtained for the substructure impedance when the number of sub-oscillators approaches Infinity. It is found that the induced damping depends on the total mass of the sub-oscillators resonating in a frequency band of interests and nearly independent of their Individual loss factors. A modal overlapping condition. which corresponds to bandwidths that exceed the spacing of those natural frequencies, is required for the sub-oscillators to have such effects. An impulse response of the system is also considered. When the sub-oscillators lack damping and do not satisfy the modal overlapping condition, the vibratory energy is returned from the sub-oscillators to the main structure at later times. The result of this paper is consistent with that found with the fuzzy structure and SEA framework.

• Journal of Animal Science and Technology
• /
• 제65권5호
• /
• pp.1065-1080
• /
• 2023

The solubility and structure of myosin and the properties of pork gel with NaCl, KCl, CaCl₂, and MgCl₂ were investigated. Myofibrillar proteins (MPs) with phosphate were more solubilized with NaCl than with KCl (p < 0.05). CaCl₂ and MgCl₂ showed lower MP solubilities than those of NaCl and KCl (p < 0.05). The α-helix content of myosin was lower in KCl, CaCl₂, and MgCl₂ than in NaCl (p < 0.05). The pH of pork batter decreased in the order of KCl, NaCl, MgCl₂, and CaCl₂ (p < 0.05). The cooking yield of the pork gel manufactured with monovalent salts was higher than that of the pork gel manufactured with divalent salts (p < 0.05). The pork gel manufactured with KCl and MgCl₂ showed lower hardness than that of the pork gel manufactured with NaCl. The solubility and structure of myosin were different with the different chloride salts and those led the different quality properties of pork gel. Therefore, the results of this study can be helpful for understanding the quality properties of low-slat meat products manufactured by replacing sodium chloride with different chloride salts.

• Bulletin of the Korean Chemical Society
• /
• 제31권2호
• /
• pp.360-364
• /
• 2010

$Li_4Ti_5O_{12}$ thin film with inverse hemispheric structure was fabricated on a Pt/Ti/$SiO_2$/Si substrate by the sol-gel and dip coating method for use as an anode for 3-dimensional (3D) thin-film batteries. Polystyrene (PS) beads of 400 nm diameter were used to prepare the template for the inverse hemispheric structure. A coating solution prepared using precursor sources was dropped on the template-deposited substrates, which were then calcinated at $400^{\circ}C$. The template was removed by calcination, and the inverse hemispheric structure was successfully formed by an annealing process. The cyclic performance during high-rate charge/discharge processes of the $Li_4Ti_5O_{12}$ film with inverse hemispheric structure was superior to that of the flat $Li_4Ti_5O_{12}$ film.

• Journal of the Korean Ceramic Society
• /
• 제40권1호
• /
• pp.52-61
• /
• 2003

$SrBi_2Ta_2O_9(SBT)$and$ZrO_2$thin films for MFIS structure(Metal-Ferroelectric-Insulator-Semiconductor) were deposited by RF magnetron sputtering method. In order to investigate the effect of heat treatment of insulator layers and MFIS structure, the insulator layers were heat treated from $550^{circ}C;to; 850^{\circ}C$in conventional furnace or RTA furnace under$O_2$and Ar ambient, respectively. After then, C-V characteristics and leakage current were measured. The capacitor with 20 nm thick $ZrO_2$layer treated at RTA$750^{circ}C;in;O_2$ atmosphere had the largest memory window. The C-V and leakage current characteristics of the$Pt/SBT(260nm)/ZrO_2(20nm)/Si$structure were better than those of$Pt/SBT(260nm)/Si$ structure. These results showed that$ZrO_2$films took a role of buffer layer effectively.

• Transactions of the Korean hydrogen and new energy society
• /
• 제23권6호
• /
• pp.654-659
• /
• 2012

The interest in water gas shift (WGS) reaction has grown significantly, as a result of the recent advances in fuel cell technology and the need to develop small-scale fuel processors. Recently, researchers have tried to overcome the disadvantages of the commercial WGS catalysts. As a consequence, supported Pt catalysts have attracted a lot of researchers due to high activity and stability for WGS at low temperatures. In this study, $Pt-Na/Ce_{(1-x)}Zr_{(x)}O_2$ catalysts with various Ce/Zr ratio have been applied to WGS at a gas hourly space velocity (GHSV) of $45,515h^{-1}$. According to TPR patterns of $Pt-Na/Ce_{(1-x)}Zr_{(x)}O_2$ catalysts, the reducibility increases with decreasing the $ZrO_2$ content. As a result, Cubic structure $Pt-Na/Ce_{(1-x)}Zr_{(x)}O_2$ catalysts exhibited higher CO conversion than tetragonal structure $Pt-Na/Ce_{(1-x)}Zr_{(x)}O_2$ catalysts. Expecially, Pt-Na/$CeO_2$ exhibited the highest CO conversion as well as 100% selectivity to $CO_2$. Moreover, Pt-Na/$CeO_2$ catalyst showed relatively stable activity with time on stream. The high activity of cubic structure Pt-Na/$CeO_2$ catalyst was correlated to its higher oxygen storage capacity (OSC) of $CeO_2$ and easier reducibility of Pt/$CeO_2$.

• Journal of the Korean Ceramic Society
• /
• 제45권5호
• /
• pp.290-296
• /
• 2008

$AB'_{0.5}B"_{0.5}O_3$ type complex perovskite structures which have been reported as proton conductors over $600^{\circ}C$ were studied. The $AB'_{0.5}B"_{0.5}O_3$ type complex perovskite structure is known to be more easily synthesized and has better stability than normal $ABO_3$ perovskite structure. And it is stable at about $800^{\circ}C$ in the $CO_2$ atmosphere, whereas the $BaCeO_3$ perovskite is easily decomposed into carbonate. In addition, this $AB'_{0.5}B"_{0.5}O_3$ type complex perovskite structure could simply produce oxygen vacancies within their structure not by introducing additional doping oxides but by just controling the molar ratio of $B'^{+3}$ and $B"^{+5}$ metal ions in the B site. Hence it is easy to design the structure which shows highly sensitive electrical conductivity to humidity. In this study, the single phase boundary of $BaR_{0.5+x}Ta_{0.5-x}O_{3-{\delta}}$(R = rare earth) complex perovskite structures and it's phase stability were investigated with changes in composition, x. And the humidity dependance of electrical conductivity at different $P_{H2O}$ conditions was investigated.

• Journal of Powder Materials
• /
• 제27권5호
• /
• pp.406-413
• /
• 2020

Ti_0.5Al_0.5N/CrN nano-multilayers, which are known to exhibit excellent wear resistances, were prepared using the unbalanced magnetron sputter for various periods of 2-7 nm. Ti_0.5Al_0.5N and CrN comprised a cubic structure in a single layer with different lattice parameters; however, Ti_0.5Al_0.5N/CrN exhibited a cubic structure with the same lattice parameters that formed the superlattice in the nano-multilayers. The Ti_0.5Al_0.5/CrN multilayer with a period of 5.0 nm exceeded the hardness of the Ti_0.5Al_0.5N/CrN single layer, attaining a value of 36 GPa. According to the low-angle X-ray diffraction, the Ti_0.5Al_0.5N/CrN multilayer maintained its as-coated structure up to 700℃ and exhibited a hardness of 32 GPa. The thickness of the oxidation layer of the Ti_0.5Al_0.5N/CrN multilayered coating was less than 25% of that of the single layers. Thus, the Ti_0.5Al_0.5N/CrN multilayered coating was superior in terms of hardness and oxidation resistance as compared to its constituent single layers.

• Journal of the Korean institute of surface engineering
• /
• 제54권4호
• /
• pp.178-183
• /
• 2021

The temperature and frequency dependence of the dielectric constant of the BaTiO₃ substituted with two types of donor dopants, Nb⁵⁺ and Ta⁵⁺, respectively, were compared and analyzed. Dielectric specimens of four specific compositions, Ba_0.95Nb_0.05TiO₃, Ba_0.90Nb_0.10TiO₃, Ba_0.95Ta_0.05TiO₃, and Ba_0.90Ta_0.010TiO₃ were prepared by calcining at 1100 ℃ and sintering at 1300 ℃ to have a perovskite structure to measure capacitance. XRD and SEM analysis were used to observe the structure, with particular focus on the integration into the Nb⁵⁺ and Ta⁵⁺ substituted BaTiO₃ crystal lattice. X-ray diffraction peaks in the (200) and (002) planes were observed between 45.10° and 45.45° of the BaTiO₃ solid solution substituted with different fractions of Nb⁵⁺ and Ta⁵⁺. The dielectric properties were analyzed and the relationship between the properties and structure of the substituted BaTiO₃ was established. The fine particles and high density of the substituted BaTiO₃ were maintained like pure BaTiO₃, and in particular, a shift toward the low temperature side of the phase transition temperature range was clearly found, unlike pure BaTiO₃. In addition, the phase transition at a temperature higher than the Curie temperature relatively satisfies the modified Curie-Weiss law.

• Journal of Electrochemical Science and Technology
• /
• 제12권3호
• /
• pp.346-357
• /
• 2021

In recent years, supercapacitors have been developed rapidly as a rechargeable energy storage device. And the performance of supercapacitors is depending on electrode materials, the preparation method and performance of electrode materials have become the primary goal of scientific development. This study synthesizes Co₃O₄@MnO₂@PPy cathode material with porous pattern core-shell structure by hydrothermal method and electrodeposition. The result samples are characterized by X-ray diffraction transmission/scanning electron microscope, and X-ray photoelectron spectroscopy. Electrochemical evaluation reveals that electrochemical performance is significantly enhanced by PPy depositing. The specific capacitance of Co₃O₄@MnO₂@PPy is 977 F g^-1 at 1 A g^-1, the capacitance retention rate of 105%. Furthermore, the electrochemical performance of Co₃O₄@MnO₂@PPy//AC asymmetric supercapacitor assembles with AC as the negative electrode material is significantly better than that of MnO₂//AC and Co₃O₄@MnO₂//AC. The capacity of Co₃O₄@MnO₂@PPy//AC is 102.78 F g^-1. The capacity retention rate is still 120% for 5000 charge-discharge cycles.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• 제16권10호
• /
• pp.865-870
• /
• 2003

The MFIS (Metal-Ferroelectric-Insulator-Semiconductor) capacitors were fabricated using a metalorganic decomposition method. Thin layers of CeO$_2$ were deposited as a buffer layer on Si substrate and BLT thin films were used as a ferroelectric layer. The electrical and structural properties of the MFIS structure were investigated. X -ray diffraction was used to determine the phase of the BLT thin films and the quality of the CeO$_2$ layer. The morphology of films and the interface structures of the BLT and the CeO$_2$ layers were investigated by scanning electron microscopy. The width of the memory window in the C-V curves for the MFIS structure is 2.82 V. The experimental results show that the BLT-based MFIS structure is suitable for non-volatile memory FETs with large memory window.