• Journal of Industrial Technology
• /
• v.18
• /
• pp.173-180
• /
• 1998

A high speed and stable A/D conversion data process is required to weigh a mass on moving conveyer weighing platter. The paper presents a new method to obtain stable and fast automatic weighing A/D conversion data process. Dynamic weighting system which is constructed with dual load cell is realized by the stable A/D conversion data process algorithm using DSP. The proposed method is applied to the real design, and that experimental results showed good performances of the weighing stability.

• Korean Chemical Engineering Research
• /
• v.53 no.5
• /
• pp.531-539
• /
• 2015

Chlor-alkali industry is one of the largest electrochemical processes which annually producing 70 million tons of sodium hydroxide and chlorine from sodium chloride solution. $DSA^{(R)}$ (Dimensionally Stable Anodes) electrodes such as $RuO_2$ and $IrO_2$, which is popular in chlor-alkali process, have been investigated to improve the chlorine generation efficiency. Although DSA electrode has been developed with various researches, understanding of the chlorine evolution mechanism is essential to the development of highly efficient DSA electrode. In this review paper, chlorine generation mechanisms are summarized and that of key factors are identified to systematically understand the chlorine generation mechanism. Rate determining step, effect of pH, reaction intermediate, and electrode crystal structure were intensively overviewed as key factors of the chlorine mechanism.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.2
• /
• pp.203-209
• /
• 2004

Compliant bi-stable mechanism allows two stable states within its operation range staying at one of the local minimum states of the potential energy. Energy storage characteristics of the bi-stable mechanism offer two distinct and repeatable stable states, which require no power input to maintain it at each stable state. This paper suggests an equivalent model of the chevron-type bi-stable microactuator using the equivalent spring stiffness in the rectilinear and the rotational directions. From this model the range of spring stiffness where the bi-stable mechanism can be operated is analyzed and compared with the results of the FEA (Finite Element Analysis) using ANSYS for the buckling analysis, both of which show a good agreement. Based on the analysis, a newly designed chevron-type bi-stable MEMS actuator using hinges is suggested for the latch-up operation. It is found that the experimental response characteristics of around 36V for the bi-stable actuation for the 60$mu extrm{m}$ stroke correspond very well to the results of the equivalent model analysis after the change in cross-sectional area by the fabrication process is taken into account. Together with the resonance frequency experiment where 1760Hz is measured, it is shown that the chevron-type bi-stable MEMS actuator using hinges is applicable to the optical switch as an actuator.

• Communications of the Korean Mathematical Society
• /
• v.12 no.3
• /
• pp.725-741
• /
• 1997

This paper considers the problem of deriving exponential probability inequalities for product symmetric Poisson processes. As an application they are used to show the existence of regular version of some product process derived from L$\acute{e}$vy process.

• Journal of Power System Engineering
• /
• v.20 no.2
• /
• pp.43-50
• /
• 2016

This research proposal is based on a novel non-contact technique of micro-sized bead injection process for fabrication of electronic paper display. This non-contact injection process is based on the principle of electrostatic force and uses micro-sized metal-coated beads dispersed in a solution. The dispersion retention times of three different solutions with viscosities of 10 cps, 100 cps, and 1000 cps were measured by optical equipment showing the retention times of 5 mins, 10 mins, and 30 mins respectively. The dispersion retention rate dropped as the time passed. The dispersion retention characteristic of 1000 cps solution was more stable as compared to those of 10 cps and 100 cps meaning that higher viscosity has better retention properties. The experimental results of bead injection at different viscosity levels of the solution were also measured and a stable injection result was achieved by using 1000 cps solution. This results show that stable injection is dependent on solution viscosity and dispersion.

• Transactions of the Korean hydrogen and new energy society
• /
• v.34 no.2
• /
• pp.212-225
• /
• 2023

This study presents a modularized process of a hybrid renewable energy system that combines photovoltaic power and wind power to supply stable power in a unit area (1 km²). The water electrolysis process and fuel cells process also contributes to the supply of the stable power. The entire system can constantly supply power of 4.39 MW/km². Actual meteorological data is used for simulation.

• Journal of Korean Society on Water Environment
• /
• v.24 no.5
• /
• pp.618-625
• /
• 2008

Advanced Phase Isolation Ditch (APID) process was studied to develop economic retrofitting technology, for the plants where retrofitting of common activated sludge process is required. In this study, to evaluate the effluent BOD, SS, T-N, and T-P concentrations as process capable and stable parameters for treating municipal wastewater, a demonstration plant was installed and operated in the existing sewage treatment plant of P city. During this study, the average effluent BOD, SS, T-N, and T-P concentrations were 4.56, 5.20, 9.30, and 1.75 mg/L at the conventional mode and 3.95, 3.17, 7.65, and 1.18 mg/L at the modified mode. The modified mode (BOD: 3.69, SS: 3.19, T-N: 1.27, and T-P: 0.69) increased the process capability more than the conventional mode (BOD: 1.80, SS: 1.05, T-N: 2.17, and T-P: 0.15) in this study. If process capability over 1.0, this process is capable and stable to treat wastewater. Therefore, newly developed APID process with modified intermittent aeration mode can be one of the useful processes for stable organic matter and nutrients removal.

• Journal of the Korean Mathematical Society
• /
• v.36 no.5
• /
• pp.923-943
• /
• 1999

In this paper we consider functionals of the empirical age distribution of supercritical Bellman-Harris processes. Let f : R+ longrightarrow R be a measurable function that integrates to zero with respect to the stable age distribution in a supercritical Bellman-Harris process with no extinction. We present sufficient conditions for the asymptotic normality of the mean of f with respect to the empirical age distribution at time t.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.26 no.3
• /
• pp.39-49
• /
• 2003

Statistical process cintrol is intended to assist operators of a stable system in monitoring whether a change has occurred in the process, and it uses several control charts as main tools. In design and use of control chart, it is rational that probability of false alarm is minimized in stable process and probability of detecting shifts is maximized in out-of-control. In this study, we establish bootstrap control limits for robust M-estimator chart by applying the bootstrap method, called resampling, which could not demand assumptions about pre-distribution when the process is skewed and/or the normality assumption is doubt. The results obtained in this study are summarized as follows : bootstrap M-estimator control chart is developed for applying bootstrap method to M-estimator chart, which is more robust to keep ARL when process contain contaminate quality characteristic.

• Journal of Advanced Marine Engineering and Technology
• /
• v.25 no.5
• /
• pp.1086-1090
• /
• 2001

In this paper, a method deciding the permissible gains of the P and PT controllers for a retarded process under stable condition is proposed. For analysis, the controlled process is assumed to be first-order system with time delay. At first, the adjustable parameter sets causing stability limit are obtained based on the frequency domain condition which makes the roots of the characteristic equation locate on the imaginary axis. And the cut-in frequency ${\omega}_p$ to bring the parameter set to P control from PI control is derived is derived in terms of L and $T_m$ then ${\omega}_p$ is used to compute the maximum gain with stable condition. The results indicate that the permissible controller gains can be described by a unique if parameters L and $T_m$ are know.