• Journal of Korea Society of Digital Industry and Information Management
• /
• v.9 no.2
• /
• pp.11-15
• /
• 2013

We in order to use WLAN communication device planned wireless USB dongle internal antenna of 2.4 GHz/5.8 GHz band. So it uses square patch dual-wideband and quality is satisfactory and it designed print folded monopole antenna of the shape which is simple. The thickness of the antenna was fed by a $50{\Omega}$ coaxial cable feeding 1mm dielectric constant 4.4 FR4 substrate was used. The overall size of the antenna is $20mm{\times}50mm$. So the internal antenna is suitable. Measurement results of the fabricated antenna, the return loss of more than 10 dB in the two bands could be obtained. Radiation pattern has a maximum gain of 3.75 dBi value.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.14 no.1
• /
• pp.55-60
• /
• 2019

Because of an rapid increase of using a wireless Internet, the originally used communication of 2.4 GHz band was saturated and crossed and there were some problems. According to this, the development of a wireless Internet technology of 5 GHz Band proceeded. In the thesis we researched a Square Slot Microstrip Patch Antenna available in 5 GHz band of wireless communication. The research designed and analyzed the Antenna through HFSS. Ultimately, we compared and analyzed made Antenna through a Network Analyzer.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.6
• /
• pp.638-647
• /
• 2003

Triangular patches have been studied, both theoretically and experimentally. We feund that provided radiation characteristics similar to those of rectangular patches, but with smaller size. In this paper, we designed an equilateral triangular microstrip patch antenna using cavity model analysis. Then, in order to improve narrow bandwidth, we add capacitive gap and air gap. Capacitive gap is located with square shape beside feeding point on the patch, and air gap is inserted between substrate dielectric and ground plane to adjust probe inductance. The analysis of characteristics and effects of each component was performed by commercial simulation tool, Ensemble 5.0. Throughout the simulation and experiment, we found the possibility of bandwidth enhancement in triangular microstrip antenna.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.39A no.6
• /
• pp.310-321
• /
• 2014

Effect of substrate thickness, perforation position and size on the bandwidth and radiation characteristics of a proximity coupled perforated microstrip patch antenna (PCPPA) with $2{\times}2$ square perforations inside a patch is investigated. As the thicknesses of antenna substrate and feed substrate increase, the bandwidth of a PCPPA increases without the degradation of radiation characteristics. As the position of a perforation moves toward the edge of a patch along the length direction, the bandwidth of a PCPPA increases without the degradation of radiation characteristics, while the effect of changing the position of a perforation along the width direction on the bandwidth and radiation characteristics of a PCPPA is negligible. As the perforation size is decreased, the bandwidth of a PCPPA is increased and the radiation characteristics of a PCPPA are enhanced.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.1
• /
• pp.1-9
• /
• 2014

In this paper, a reconfigurable polarization patch antenna that uses a Y-shaped feed is proposed. The proposed antenna consists of a square patch, a Y-shaped feeding structure, a PIN diode, and a bias circuit for diode operation. The structural symmetry/asymmetry of the feeding structure is determined by the on/off operation of the PIN diode that inserted into the side of one of the lines of the Y-shaped feeding structure. For the proposed reconfigurable antenna, the two microstrip lines of the feeding structure have the same length when the PIN diode operates in the on state, and the antenna exhibits linear polarization(LP). On the other hand, when the PIN diode operates in the off state, the length of one side line of the feeding structure is relatively shorter than that of the other line. Therefore, the antenna exhibits circular polarization(CP). From the measurement results, it is found that the proposed antenna exhibits good impedance matching and axial ratio. In addition, polarization switching can be easily achieved in the same operating band.

• Journal of IKEEE
• /
• v.17 no.2
• /
• pp.140-144
• /
• 2013

This paper presents the novel design of circular polarized Ka-band horn array antenna. The element antenna of the arrya is composed of two parts, microstrip patch and square horn, and the microstrip patch is fed by corner truncated microstrip patch for circular polarization. The patch antenna has the role of a feeder and polarizer of the horn, thus the whole size of the horn antennae can be considerably reduced. The $1{\times}8$ horn array was designed and fabricated by the spacing of $0.9{\lambda}_0$ among the element horn. The element horn has typical gain of 8dBi and axial-ratio bandwidth of 4.9% at 3dB, and the minimum gain and axial-ratio bandwithd of the array is 14dBi and 8.2%.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.22 no.5
• /
• pp.463-474
• /
• 2009

Double symmetric patch repair of existing structures always causes membrane action only, however, in many cases this technique is not practical. On the other hand, the bending stiffness of the patch and the skin increases as tensile loading is increased and affects the bending deformation significantly in the case of single-sided patch repair. In this study, the p-convergent full layerwise model has been proposed to determine the stress concentration factor in the vicinity of a circular hole as well as across the thickness of plates with single-sided patch repair. In assumed displacement field, the strain-displacement relations and 3-D constitutive equations of a layer are obtained by the combination of 2-D and 3-D hierarchical shape functions. The transfinite mapping technique has been used to represent a circular boundary and Gauss-Lobatto numerical integration is implemented in order to directly obtain stresses occurred at the nodal points of each layer without other extrapolation techniques. The accuracy and simplicity of the present model are verified with comparison of the previous results in literatures using experiment and conventional 3-D finite element. Also, the bending effect has been investigated with various patch types like square, circular and annular shape.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2001.11a
• /
• pp.157-160
• /
• 2001

본 논문에서 5.8GHz의 주파수 대역에서 사용할 수 있는 향상된 커플링 구조와 크기를 줄인 dual-mode microstrip bandpass filter를 설계하였다. 여기서 meander loop resonator를 쓰는 이유는 크기가 작고 방사 손실이 적으며 패턴이 간단하기 때문이다. 또한 이와 비슷한 특성을 갖는 ring, square patch, disk등은 불연속 성분을 가짐으로써 이중모드의 구현이 가능하다. 향상된 형태의 dual-mode microstrip bandpass filter의 변형된 T-shaped meander loop resonator를 소형으로 발전되고. 높은 선택도를 가지는 구조이다. 이 형태의 filter에서 150MHz의 bandwidth을 가지고 5.8GHz주파수를 가지는 구조로 설계하였다.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2002.10a
• /
• pp.591-598
• /
• 2002

The interface element method for non-matching FEM meshes is extended using stabilized nodal integration. Two non-matching meshes are shown to be joined together compatibly, with the aid of the moving least square approximation. Using stabilized nodal integration, the interface element method is able to satisfy the patch test, which guarantees the convergence of the method.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.20 no.4
• /
• pp.451-460
• /
• 2014

In this paper, we examined the problem of the structural stability according to the patch load of a rectangular plate that reflects the material properties of A6082-T6 is used primarily for marine plant structure. it applied to the four patch loading shapes, the effect of aspect ratio, a boundary condition and calculated the critical elastic buckling load. Calculating the critical elastic buckling load, During the eigenvalue buckling analysis it is applied to the shell181 as 4 node shell element. when the plate subjected to patch loading compare to the plate under a uniform axial compression load, it is possible observed to occur the different elastic buckling behaviour and it could be confirmed that it is affected significantly on a variable position and type of loadings, such as the effect of the aspect ratio. Also, Critical elastic buckling load according to th patch loading type in simply supported rectangular plate a/b=1.0, ${\gamma}b$=200mm are calculated 67%(Loading type I), 119 %(Loading type II), 76 %(Loading type III), 160 %(Loading type IV), respectively. Loading type I and III could be determined with the strong elastic buckling behavior much more than Loading type II and IV.