• 한국전기전자재료학회논문지
• /
• 제22권3호
• /
• pp.269-276
• /
• 2009

Antimony doped tin oxide ($SnO_2:Sb$) films, which are used as the front contact and back reflector of thin film solar cells, have been deposited by d,c, magnetron sputtering. The dependence of electrical and optical properties of the films on the preparation conditions, such as $O_2$ gas ratio, substrate temperature, annealing temperature was investigated. The sputter gas composition was found to affect the properties of the films. With incorporating $O_2$ gas, the electrical and optical properties of films significantly were improved. The minimum resistivity and optical transmittance over 80 % in visible region were obtained at the oxygen concentration of 30 %, When the substrate temperature was higher, the resistivity of $SnO_2:Sb$ films was decreased, while the absorption edge shifted to shorter wavelength, indicating higher optical band gap. Heat treatment over $600^{\circ}C$ resulted in poorer electrical and optical properties due to SnO phase (102) plane.

• 한국전기전자재료학회논문지
• /
• 제11권5호
• /
• pp.418-422
• /
• 1998

The Co-Cr films are one of the most suitable candidates for perpendicular magnetic recording media. The facing targets sputtering(FTS) system has a advantage of preparing films over a wide range of working gas pressure on plasma-free substrate. In this study, we investigated the possibility of employing FTS system for depositing Co-Cr films. The Co-Cr thin films were deposited with various sputter gas pressure($P_Ar$, 0.1~10mTorr) by using FTS apparatus at temperature of $40^{\circ}C and 220^{\circ}C$, respectively. Crystallographic and magnetic characteristics were evaluated by x-ray diffractometry (XRD) and vibrating sample magnetometer(VSM), respectively. Under argon gas pressure at 0.1mTorr, films with morphologically dense microstructure, good c-axis orientation and higher coercivity were obtained. It has been confirmed that the FTS system is very useful for preparing Co-Cr thin film recording media.

• 한국재료학회지
• /
• 제20권5호
• /
• pp.267-270
• /
• 2010

Sn doped $In_2O_3$ (ITO) and ITO/Cu/ITO (ICI) multilayer films were prepared on glass substrates with a reactive radio frequency (RF) magnetron sputter without intentional substrate heating, and then the influence of the Cu interlayer on the methanol gas sensitivity of the ICI films were considered. Although both ITO and ICI film sensors had the same thickness of 100 nm, the ICI sensors had a sandwich structure of ITO 50 nm/Cu 5 nm/ITO 45 nm. The ICI films showed a ten times higher carrier density than that of the pure ITO films. However, the Cu interlayer may also have caused the decrement of carrier mobility because the interfaces between the ITO and Cu interlayer acted as a barrier to carrier movement. Although the ICI films had two times a lower mobility than that of the pure ITO films, the ICI films had a higher conductivity of $3.6{\cdot}10^{-4}\;{\Omega}cm$ due to a higher carrier density. The changes in the sensitivity of the film sensors caused by methanol gas ranging from 50 to 500 ppm were measured at room temperature. The ICI sensors showed a higher gas sensitivity than that of the ITO single layer sensors. Finally, it can be concluded that the ICI film sensors have the potential to be used as improved methanol gas sensors.

• 센서학회지
• /
• 제23권5호
• /
• pp.291-294
• /
• 2014

In this study, a chemiresistive sensor based on one-dimensional $WO_3$ nanostructures is presented for application in non-invasive medical diagnostics. $WO_3$ nanostructures were used as an active gas sensing layer and were deposited onto a $SiO_2/Si$substrate using Pt interdigitated electrodes (IDEs). The IDE spacing was $5{\mu}m$ and deposition was performed using RF sputter with glancing angle deposition mode. Pt IDEs fabricated by photolithography and dry etching. In comparison with thin film sensor, sensing performance of nanostructure sensor showed an enhanced response of more than 20 times when exposed to 50 ppm acetone at $400^{\circ}C$. Such a remarkable faster response can pave the way for a new generation of exhaled breath analyzers based on chemiresistive sensors which are less expensive, more reliable, and less complicated to be manufactured. Moreover, presented sensor technology has the potential of being used as a personalized medical diagnostics tool in the near future.

• Transactions on Electrical and Electronic Materials
• /
• 제16권5호
• /
• pp.264-267
• /
• 2015

AlCrNO cermet films were prepared on aluminum substrates using a DC-reactive magnetron sputtering method and a water-cooled Al:Cr target. The Al₂O₃/AlCrNO (LMVF)/AlCrNO (MMVF)/AlCrNO (HMVF)/Al/substrate of the 5 multi-layers was prepared according to the Ar and (N₂ + O₂) gas-mixture rates. The Al₂O₃ of the top layer is the anti-reflection layer of triple AlCrNO (LMVF)/AlCrNO (MMVF)/AlCrNO (HMVF) layers, and an Al metal forms the infrared reflection layer. In this study, the crystallinity and surface properties of the AlCrNO thin films were estimated using X-ray diffraction (XRD) and field-emission scanning electron microscopy (FESEM), while the composition of the thin films was systematically investigated using Auger electron spectroscopy (AES). The optical properties of the wavelength spectrum were recorded using UH4150 spectrophotometry (UV-Vis-NIR) at a range of 0.3 μm to 2.5 μm.

• ETRI Journal
• /
• 제35권6호
• /
• pp.1156-1159
• /
• 2013

We investigate the characteristics of $Cu_2O$ thin films deposited through the addition of $N_2$ gas. The addition of $N_2$ gas has remarkable effects on the phase changes, resulting in improved electrical and optical properties. An intermediate phase ($6CuO{\cdot}Cu_2O$) appears at a $N_2$ flow rate of 1 sccm, and a $Cu_2O$ (200) phase is then preferentially grown at a higher feeding amount of $N_2$. The optical and electrical properties of $Cu_2O$ thin films are improved with a sufficient $N_2$ flow rate of more than 15 sccm, as confirmed through various analyses. Under this condition, a high bandgap energy of 2.58 eV and a conductivity of $1.5{\times}10^{-2}$ S/cm are obtained. These high-quality $Cu_2O$ thin films are expected to be applied to $Cu_2O$-based heterojunction solar cells and optical functional films.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.2
• /
• pp.783-786
• /
• 2003

Thin films of vanadium oxide(VOx) have been deposited by r.f. magnetron sputtering from $V_2O_5$ target in gas mixture of argon and oxygen. The oxygen/(oxygen+argon) partial pressure ratio of 0% and 8% is adopted. Crystal structure and optical properties of films sputter-deposited under different oxygen gas pressures and in situ annealed in vacuum at $400^{\circ}C$ for 1h and 4h are characterized through XRD and optical absorption measurements. The films as-deposited are amorphous, but $0%O_2$ films annealed for time longer than 4h and $8%O_2$ films annealed for time longer than 1h are polycrystalline. The optical transmission of the films annealed in vacuum decreases considerably than the as-deposited films and the optical absorption of all the films increases rapidly at wavelength shorter than about 550nm. Indirect and direct optical band gaps were decreased with increasing the annealing time.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 하계학술대회 논문집 D
• /
• pp.1279-1281
• /
• 1998

The Co-Cr thin films are one of the most suitable candidates for perpendicular magnetic recording media. The facing targets sputtering(FTS) method has a advantage of preparing films over a wide range of working gas pressure on plasma-free substrates. In this study, we investigated the possibility of employing FTS system for depositing Co-Cr films, Co-Cr thin films were deposited with continuously sputter gas pressure ($P_{Ar}$ = 0.1 mTorr) by FTS method at temperature of $40^{\circ}C$. We find that the change of thickness and deposition rate of sputtered Co-Cr thin films affect crystal orientation and magnetic properties. Crystallographic and magnetic properties were evaluated by x-ray diffractometry(XRD) and vibrating sample magnetometer(VSM) respectively. It has been confirmed that the FTS method is very useful for preparing Co-Cr thin film recording media.

• 한국세라믹학회지
• /
• 제51권3호
• /
• pp.190-196
• /
• 2014

Flexible $TiO_2$ films were deposited as dielectric materials for high-energy-density capacitors on polyethylene terephthalate (PET) substrates using a roll-to-roll sputtering method. Both the growth behavior and electrical properties of the flexible $TiO_2$ films were dependent on the sputtering pressure and $O_2$/Ar gas ratio during the sputtering process. All $TiO_2$ films had an amorphous structure regardless of the sputtering conditions due to the low substrate temperature. Microstructural characteristics such as the surface morphology and roughness of the films degraded with an increase in the sputtering pressure and $O_2$ gas concentration. The $TiO_2$ films deposited at a low pressure showed better electrical properties than those of films deposited at a high pressure. The $TiO_2$ films prepared at 10 mTorr exhibited a dielectric constant of approximately 90 at 1 kHz and a leakage current density of $5{\sim}6{\times}10^{-7}A/cm^2$ at 3 MV/cm.

• Transactions on Electrical and Electronic Materials
• /
• 제6권1호
• /
• pp.10-13
• /
• 2005

$Sr_{0.6}Ba_{0.4}Nb_{2}O_{6}$, hereafter SBN60, thin films of 300 nm thickness were deposited using ion beam sputtering technique, in which sintered ceramic target of the same composition was utilized and the $Ar:O_{2}$ gas ratio was controlled during deposition onto $Pt(100)/TiO_{2}/SiO_{2}/Si$ substrate. Crystallization and orientation behavior as well as electrical properties of the films were examined after annealing treatment at $650{\sim}800{\cric}C$. It was found that the film orientation was dependent upon $Ar:O_{2}$ratio, in which strong (00l) orientation was developed when the gas ratio was about 1:4 at $4.3{\times}10^{-4}$ torr. Typical remanent polarization (2Pr), the coercive field (Ec) and the dielectric constant of Pt/SBN60/Pt thin film capacitor were approximately $10{\mu}C/cm^{2}$, 60 kV/cm, and 615, respectively.