• Journal of Power System Engineering
• /
• v.20 no.5
• /
• pp.29-36
• /
• 2016

Aluminum alloys have been widely used in engine materials, cold & hot-water storage vessels and piping etc., Furthermore, the aluminum alloy of AC8A have been widely used in mold casting material of engine piston for various vehicles because of its properties of temperature, wear and corrosion resistance. Therefore, it is considered that evaluation of corrosion resistance as well as wear resistance of AC8A material is also important to improve its property and to prolong its lifetime. In previous paper, the effect of solution($510^{\circ}C$:4hrs) and tempering($190^{\circ}C$: 16, 24, and 36 hrs)heat treatments to corrosion resistance and hardness were investigated using electrochemical method. In this study, in order to examine completely the effect of the tempering hours to hardness variation and corrosion resistance, the results of solution($510^{\circ}C$:4hrs) and tempering($190^{\circ}C$: 2, 4, 8 and 12hrs)heat treatments to hardness and corrosion resistance were investigated using electrochemical method. The hardness decreased with solution heat treatment compared to mold casting condition, but its value increased with tempering heat treatment. Furthermore, the corrosion resistance increased with decreasing of the hardness, and decreased with increasing of the hardness reversely. And the tempering heat treatment temperature at $190^{\circ}C$ for 8 hrs exhibited the highest value of the hardness and also indicated the highest corrosion current density. However, the values of hardness and corrosion current density was again increasingly decreased with increasing of tempering hours than 8 hrs, Consequently, it is suggested that decision of the optimum. tempering hours is very important to improve the corrosion or wear resistance.

• Journal of Power System Engineering
• /
• v.14 no.2
• /
• pp.78-83
• /
• 2010

This study was carried out to investigate the effect of microstructure on the damping capacity of 12Cr martensite heat-resisting steels, in case of the specimen with martensite phase contained the volume faction of ferrite phases, under 5%. The damping capacity was decreased with the increase of solution treatment temperature and time. While it was increased with the increase of tempering temperature and time. The damping capacity was higher in case of specimen with martensite single phase structure than the specimen with martensite phase contained of ferrite phases.

• Journal of Korea Foundry Society
• /
• v.12 no.5
• /
• pp.397-402
• /
• 1992

The effect of the solution & aging treatment on the tensile strength, yield strength, elongation, reduction of area, hardness was studied in the 17-4 PH stainless steel. SEM pictures were also taken in order to examine the fracture surfaces and precipitated particles. X-ray diffraction patterns for the heat treated samples were also observed. Mechanical properties of the heat treated samples were superior to those of as cast samples. Tensile strength, yield strength, hardeness decreased with the increase of aging temperature. On the other hand, elongation and reduction of area increased as the aging temperature increased.

• Textile Coloration and Finishing
• /
• v.7 no.3
• /
• pp.60-67
• /
• 1995

This study was made to investigate the effect of silk fabrics treated with mimosa and tannic acid-weighting effect, surface color according to temprature, treatment time, concentration, pH. The results were as follows ; 1. The wavelength of maximum absorption of mimosa and tannic acid solution appeared at 278.5nm and 275.0nm, respectively. By the irradiation, spectra at wavelength of maximum absorption of mimosa solution disappeared, but those of tannic acid solution decreased after 48hr irradiation. 2. The tannin weighting increased with the increase of concentration, treatment temperature at 8$0^{\circ}C$, acidic condition. In case of tannic acid, it was higher than mimosa. 3. Surface color of silk fabric with mimosa changed from 2.8YR to 5.8YR acc-ording to the increase o( tannin concentration but in case of tannic acid itchanged from 4.2Y to 3.9Y. It was more changed acidic or alkaline conditionthan origine solution.

• The Korean Journal of Community Living Science
• /
• v.21 no.1
• /
• pp.71-79
• /
• 2010

This study was conducted to develop fresh-cut and processed pears. After treatment of citric acid (1%) or N-acetylcysteine (0.2 M), and co-treatment of citric acid (1%) and N-acetylcysteine (0.2 M) into the pears c.v. 'Wonhwang', the quality changes of pears during cold storage ($1^{\circ}C$) for 10 days were investigated respectively. Pear quality and the taste of pears increased much more in those treated with anti-browning agents than those in the control group at 10 days after anti-browning treatment and cold storage. Changes in Hunter b values of pears treated with 0.2 M N-acetylcysteine were insignificant. Those with Polyphenol oxidase (PPO) activity and ethylene production were had the most decreased effects and those with the phenolics compound contents were the most lowered. Firmness of fruits increased in treatment of 0.2 M N-acetylcysteine + 1% citric acid solution. The amount of respiration decreased in the application of 1% citric acid solution. Consequently, fruit freshness can be maintained more effectively by the treatment of the anti-browning agent compared to non-treatment, even if the effectiveness were different among different kinds of anti-browning agents.

• Corrosion Science and Technology
• /
• v.14 no.2
• /
• pp.93-98
• /
• 2015

Recently, Stainless steels have been increasingly selected as the fitting or the valve materials of water pipes as the human health issue is getting higher and higher. Therefore, the connectors attached at pipes to deliver water are exposed to more severe environments than the pipes because crevice or galvanic corrosion is apt to occur at the fittings or the valves. Effects of the solid solution annealing, cooling rate after this heat treatment, and passivation on the corrosion properties of the shell mold casted SSC13 (STS304 alloy equivalent) were studied. The heating and quenching treatment more or less reduced hardness but effectively improved corrosion resistance. It was explained by the reduction of delta ferrite contents. Independent of heat treatment, the chemical passivation treatment also lowered corrosion rate but the improvement of corrosion resistance depended on temperature and time for passivation treatment indicating that the optimum conditions for passivation treatment were the bath temperature of $34^{\circ}C$ and operating time of 10 minutes. Therefore it is suggested that the corrosion resistance of SSC13 can be effectively improved with the heat treatment, where SSC13 is heated for 10 minutes at $1120^{\circ}C$ and quenched and passivation treatment, where SSC13 is passivated for at least 10 seconds at $34^{\circ}C$ nitric acid solution.

• Journal of environmental and Sanitary engineering
• /
• v.17 no.3
• /
• pp.37-45
• /
• 2002

The Purpose of this study is to reduce environmental problems caused by landfill of bituminous coal fly ash emitted from the power plant and to reuse it. First of all, we experimented that Al and Si elements were extracted from fly ash and investigated that extracted Al and Si elements night use a coagulant. The extraction was carried out under various conditions ; concentration of the extraction solution, calcination temperature and calcination time. As the results, it was found that the optimum conditions of the extraction of Al and Si elements from fly ash were as follows, concentration of NaOH was 5N for both of them, calcination temperature was $700^{\circ}C$ and $600^{\circ}C$ and calcination time was 1hr and 1.5hr, respectively The extracted solution was used as a coagulant to treat the diluted metal-plating solutions which contained Pb and Cu, respectively. As the result of treatment on the diluted Pb-plating solution with 315NTU, the removal efficiency of turbidity was more than 90%, and the removal efficiency of Pb was about 80%. As for treatment of the non-turbid diluted Cu-plating solution, the removal efficiency of Cu was about 98%.

• Journal of Power System Engineering
• /
• v.20 no.1
• /
• pp.42-49
• /
• 2016

This study showed that on-site ferrate(VI) solution was synthesized by wet oxidation method and applied aqueous 2,4-dichlorophenol(DCP) solution to evaluate the degradation efficiency. On-site ferrate(VI) solution was synthesized by putting $FeCl_3{\cdot}6H_2O$ in the strong alkali solution with NaClO and NaOH and applied DCP solution directly. DCP solution was extracted by the liquid-liquid method and analyzed by GC-ECD. The factors such as pH, DCP initial concentration, injected ferrate(VI) dosage, temperature were investigated. The optimum pH and temperature conditions of DCP degradation were obtained in neutral condition and $35^{\circ}C$. And the experimental results showed that DCP removal efficiency also increased with the decrease of DCP initial condition and the injected ferrate(VI) dosage.

• Journal of the Korean Ceramic Society
• /
• v.31 no.11
• /
• pp.1401-1413
• /
• 1994

The synthesis of kaolinite mineral from domestic diatomite for silica resource, commercial vailable gibbsite or alumina for alumina resource were made under various hydrothermal treatment, and the sythetic effect of acidic mineralizers, temperature treatment with time duration, particle size of alumina on formation of kaolinite mineral and the plastic properties of synthesized kaolinite were investigated. The various acidic mineralizers which are HCl, HNO3, H2SO4 and Oxalic acid were employed for hydrothermal reaction in the range of 0.01 mol/ι to 2 mol/ι concentration of each mineralizers. It was found that HCl in the level of 1 mol/ι solution produced highly yields of well-crystallized and platy form kaolinite mineral and gave the most effective extraction of iron oxide, compared to that of others, that HNO3 produced highly yield of kaolinite but lower extraction of iron oxide, that H2SO4 produced low yield of kaolinite and formed alunite mineral, and that oxialic acid formed spherical crystalline kaolinite and gave low extraction of iron oxide. Moreover, it showed that kaolinite minerals were well synthesized in a wide range of less than 2 mol/ι acids, but were poorly synthesized at more than 2 mol/ι acids. However, boehmite and kaolinite were coexistently formed in the temperature range of 18$0^{\circ}C$ and 20$0^{\circ}C$ when the calcined diatomite and gibbsite were involved. The well-ordered kaolinite mineral as a platy form was highly synthesized in the temperature range of 220 and 24$0^{\circ}C$, when the same marterials as above were used with treatment of 1 mol/ι HCl solution. The results also revealed that the size of crystalline platy form kaolinite, synthesized from alumina and calcined diatomite with treatment in 1 mol/ιHCl solution at 24$0^{\circ}C$, was much larger than that of gibbsite and calcined diatomite shown previously, and that kaolinite and corundum minerals were coexistently formed under any hydrothermal treatment conditions. The plasticity of synthesized kaolinite from under 2 ${\mu}{\textrm}{m}$ alumina and calcined diatomite was very poor, and that of the synthesized kaolinite from raw diatomite and gibbsite gave higher than that of calcined diatomite and gibbsite.

• Journal of Sericultural and Entomological Science
• /
• v.43 no.1
• /
• pp.37-40
• /
• 2001

This study was carried out to investigate the optimum condition for silk sericin collection from degumming solution using some aluminium salts with various treatment conditions and examine the thermal properties of silk sericin collected from degumming solution. Silk sericin was precipitated by treatment of aluminium metal compound from degumming solution. The best optimum collecting conditions of silk sericin from degumming solution are the concentration of 2 $m\ell$/l of polyaluminium chloride (PAC), pH range of 5~7 and room temperature. The reduction of water pollution was evaluated by decreasing the chemical oxygen demand (COD) and nitrate ion (NO$_3$￣). Thermal stability of silk sericin collected from degumming solution was a little lower than that of hot water.