• 한국막학회:학술대회논문집
• /
• 한국막학회 2004년도 Proceedings of the second conference of aseanian membrane society
• /
• pp.19-24
• /
• 2004

ED method is employed to effectively remove the organic acid salts in actual PDO fermentation broth. The lower electrical potential is selected to avoid the serious membrane fouling so as to ensure a stable and durative desalination process. Under the selected operation conditions, about 90% of organic acids salts are removed from PDO fermentation broth successfully by ED process. To reduce the loss of PDO product due to the diffusion, the operation time should be considered carefully. And based on mass balance equation and irreversible thermodynamics approach, a mathematical model is developed to describe the desalination process of an aqueous solution containing neutral solute by ED method. While the influence of concentration polarization is reflected by decreasing the conductivity of membrane, the model is verified well to describe the ED processes under varied operation conditions. Through the model, ED process of actual PDO fermentation broth is simulated to get a suitable scope of initial concentration in concentrated compartment.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1992년도 춘계학술대회 논문집
• /
• pp.50-53
• /
• 1992

The GaP crystals are growth by Synthesis Solute Diffusion(SSD) method and its properties are investigated. Etch pits density along vertical direction of ingot is increased from 3.8${\times}$10$^4$cm$\^$-2/ of first freeze to 2.3${\times}$10$\^$5/cm$\^$-2/ of last freeze part. The carrier concentration and mobilities are measured to 197.49$\textrm{cm}^2$/V. sec and 6.75${\times}$10$\^$15/cm$\^$-3/ at room temperature. The temperature dependence of optical energy gap is empilically fitted to E$\_$g/(T)=2.3383-(6.082${\times}$10$\^$-4/T${\times}$/(373.096+T)[eV]. Photo-luminescence spectra measured at low temperature are consist with sharp line-spectra near band-gap energy and radiative recombination between shallow Si-donor to Zn-acceptor and its phonon reprica, and broad emission. The infrared absorption in GaP is cause to phonon coupling modes of TO, LO, LA, TA$_1$, TA$_2$and vibration modes of Ga$_2$O, Si-donor and Zn-acceptor, respectively.

• 소성∙가공
• /
• 제32권3호
• /
• pp.107-113
• /
• 2023

The importance of dual-fuel engines has increased for reducing CO₂ emissions. However, the low operating temperature of this engine may induce low-temperature corrosion at combustion parts, which reduces the engine service life. To overcome this problem, NiCr38Al4 alloy was developed for valve spindle, but the cost of this alloy is expensive due to its high Cr content. For reducing the manufacturing cost of valve spindle, in the present work, NiCr38Al4 alloy was welded with Nimonic80A alloy by conducting friction welding. The tensile test results show that the strength of friction-welded specimens follows the properties of the lower-strength parent materials, without severe cracks at the interface. The large shear strain and frictional heat from friction welding not only reduce grain size but also induce solute element diffusion at the interfacial region. Because of the low Cr diffusivity compared with Ti, Cr carbides were not observed in the Nimonic80A matrix, while Ti carbides were distributed in both the Nimonic80A and SNCrW matrices.

• 한국토양환경학회지
• /
• 제1권2호
• /
• pp.91-101
• /
• 1996

최근에 식물을 이용한 탄화수소화합물의 정화방법은 특히, 넓은 범위에 거쳐 저농도로 오염되어 있는 토양인 경우에 앞으로 각광을 받을 가능성이 높은 새로운 연구분야로 주목을 받아왔다. 이의 기술을 실제 오염토양에 바로 적용하기전 적절한 설계에 필요한 예측 모델링의 필요성이 함께 요구되고 있다. 현재 녹지토양내의 용질과 식물과의 상호작용에 관한 많은 모델들이 나와있지만 대부분이 이온상태의 무기영향물이나 금속류의 경우에만 한정되어 있다. 본 연구에서는 토양내의 탄화수소화합물의 생물학적정화에 미치는 식물의 영향을 예측하기 위한 기본 수학적 모델식을 제안 하였다. 먼저 토양내의 식물뿌리가 토양수분과 오염물에게 미치는 영향과 비포화계층에서의 오염물의 이동현상 및 토양내 기/액상간의 물질전달을 수학적으로 나타내고자 하였으며 시간의 변화와 토양깊이별 식물의 오염물의 동태에 미치는 영향을 시뮬레이션하기 위하여 식물뿌리의 시간에 따른 양적성장과 깊이별 분포정도를 예측하기 위한 관계식도 아울러 모델링에 포함하였다. 오염물의 식물내의 흡수 및 생물막이론을 이용한 식물뿌리근처에서의 생물학적 분해에 관한 현상도 관계식을 이용 설명하고자 하였다. 본 연구에서 제시한 식물영향하의 탄화수소화합물의 토양내의 동태해석을 위한 모델식은 실제로 탄화수소화합물에 의해 오염된 토양을 식물을 이용하여 정화하고자 할때, 필요한 기본설계도구로서 유용하게 쓰여질 것으로 기대된다.

• 공업화학
• /
• 제19권6호
• /
• pp.633-639
• /
• 2008

상전환법을 이용하여 폴리설폰, n-메틸피롤리돈과 톨루엔으로 이루어진 제막용액으로부터 고분자 분리막이 제조되었다. 톨루엔은 폴리설폰에 대한 비용매로서 제막용액에 첨가되었으며, 침지용 비용매로는 이소프로필알코올이 사용되었다. 제조된 모든 분리막은 밀집 형상의 표면층과 스폰지 형상의 하부층으로 구성된 이중구조 형태의 비대칭성 구조를 보였다. 첨가된 톨루엔은 제막용액의 열역학적 성질을 변화시켜 열역학적 상분리를 촉진하는 역할을 할 수 있음을 보였으며, 제조된 분리막은 톨루엔을 첨가에 의해 막의 표면층 두께가 증가하는 특성을 보였다. 분리막의 투과 특성을 측정한 결과, 톨루엔이 첨가되었을 때 밀집 표면층의 두께 증가에도 불구하고 거의 동일한 배제율을 유지하면서 투과플럭스는 5배 이상 증대하는 효과를 보였다.

• Korean Chemical Engineering Research
• /
• 제54권4호
• /
• pp.487-493
• /
• 2016

양이온교환 고성능액체크로마토그래피에서 라이소자임을 분석하고, 실험결과인 크로마토그램을 통해 모멘트 분석을 수행하였다. 용리 인산완충용액은 1.0, 0.75, 0.5 M의 소금을 포함하였다. 실험변수는 유량, 용리 완충용액중 소금 농도, 시료의 농도로 하였다. General rate (GR) model을 도입하여 1차와 2차 모멘트를 해석하였다. 1차 모멘트 해석에서 평형상수 K를 구할 수 있으며, 이는 $L/u_0$ vs. $({\mu}_1-t_0)/(1-{\varepsilon}_e)(1-{\varepsilon}_i)$]를 도식화했을 때의 기울기이다. 2차 모멘트 해석에서 입자내 확산계수는 이론단수 실험자료에서 계산하였다. 모멘트 분석결과를 통해 여러 물질전달 현상이 이론단 상당높이(HETP)에 주는 영향을 알아보기 위해 van Deemter plot을 작성하고, 총괄 이론단 상당높이($H_{total}$)에 기여하는 $H_{ax}$, $H_f$, 그리고 $H_d$를 조사하였다. 그 중 입자내 확산계수를 나타내는 $H_d$가 가장 지배적이었고, 외부 물질전달 계수를 나타내는 $H_f$의 영향이 가장 미미했다.

• Journal of Welding and Joining
• /
• 제14권3호
• /
• pp.48-57
• /
• 1996

A study was made to examine the characteristics of base metal and stress relief cracking(SRC) of heat affected zone(HAZ) for HY-100 and Cu-bearing HSLA-100 steels. The Gleeble thermal/mechanical simulator was used to simulate the SRC/HAZ. The details of mechanical properties of base plate and SRC tested specimens were studied by impact test, optical microscopy and scanning electron microscopy. The specimens were aged at $650^{\circ}C$ for HSLA-100 steel and at $660^{\circ}C$ for HY-100 steel and thermal cycled from $1350^{\circ}C$ to $25^{\circ}C$ with a cooling time of $\Delta$t_${800^{circ}C/500^{circ}C}$=21sec. corresponds to the heat input of 30kJ/cm. The thermal cycled specimens were stressed to a predetermined level of 248~600MPa and then reheated to the stress relief temperatures of $570~620^{\circ}C$. The time to failure$(t_f)$ at a given stress level was used as a measure of SRC susceptibility. The strength, elongation and impact toughness of base plate were greater in HSLA-100 steel than in HY-100 steel. The time to failure was decreased with increasing temperature and/or stress. HSLA-100 steel was more susceptible to stress relief cracking than HY-100 steel under same conditions. It is thought to be resulted from the precipitation of $\varepsilon$-Cu phase by dynamic self diffusion of solute atoms. By the precipitation of $\varepsilon$-Cu phase, the differential strengthening of grain interior relative to grain boundary may be greater in the Cu-bearing HSLA-100 steel than in HY-100 steel. Therefore, greater strain concentration at grain boundary of HSLA-100 steel results in the increased SRC susceptibility. The activation energies for SRC of HSLA-100 steel are 103.9kcal/mal for 387MPa and 87.6kcal/mol for 437MPa and that of HY-100 steel is 129.2kcal/mol for 437MPa.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 1996년도 특별강연 및 춘계학술발표 개요집
• /
• pp.186-189
• /
• 1996

A study was made to examine the characteristics of base metal and stress relief cracking(SRC) of heat affected zone(HAZ) for HY-100 and Cu-bearing HSLA-100 steels. The Gleeble thermal/mechanical simulator was used to simulate the SRC/HAZ. The details of mechanical properties of base plate and SRC tested specimens were studied. The specimens were aged at $650^{\circ}C$ for HSLA-100 steel and at 66$0^{\circ}C$ for HY-100 steel and thermal cycled from 135$0^{\circ}C$ In $25^{\circ}C$ with a cooling time of $\Delta$ $t_{800^{\circ}50}$ $0^{\circ}C$/=21sec. corresponds to the heat input of 30kJ/cm. The thermal cycled specimens were stressed to a predetermined level of 248~600MPa and then reheated to the stress relief temperatures of 570~62$0^{\circ}C$. The time to failure( $t_{f}$) at a given stress level was used as a measure of SRC susceptibility. The strength, elongation and impact toughness of base plate were greater in HSLA-100 steel than in HY-100 steel. The time to failure was decreased with increasing temperature and/or stress. HSLA-100 steel was more susceptible to stress relief cracking than HY-100 steel under same conditions. It is thought to be resulted from the precipitation of $\varepsilon$-Cu phase by dynamic self diffusion of solute atoms. Therefore, greater strain concentration at grain boundary of HSLA-100 steel results in the increased SRC susceptibility.y.

• Metals and materials international
• /
• 제24권6호
• /
• pp.1394-1402
• /
• 2018

This study investigates the mechanism of MnS precipitation on $Al_2O_3-SiO_2$ inclusions during the solidification of non-oriented silicon steel, especially the influence of the phase structures and sizes of the oxides on the MnS precipitation, by scanning electron microscopy and transmission electron microscopy coupled with energy dispersive spectrometry. The investigation results show that MnS tends to nucleate on submicron-sized $Al_2O_3-SiO_2$ inclusions formed by interdendritic segregation and that it covers the oxides completely. In addition, MnS can precipitate on micron-sized oxides and its precipitation behavior is governed by the phase structure of the oxides. The MnS embryo formed in a MnO-containing oxide can act as a substrate for MnS precipitation, thus permitting further growth via diffusion of solute atoms from the matrix. MnS also precipitates in a MnO-free oxide by the heterogeneous nucleation mechanism. Furthermore, MnS is less prone to precipitation in the $Al_2O_3$-rich regions of the $Al_2O_3-SiO_2$ inclusions; this can be explained by the high lattice disregistry between MnS and $Al_2O_3$.

• 반도체디스플레이기술학회지
• /
• 제20권1호
• /
• pp.70-76
• /
• 2021

A cylindrical microlens (CML) has been widely used as an optical element for organic light-emitting diodes (OLEDs), light diffusers, image sensors, 3D imaging, etc. To fabricate high-performance optoelectronic devices, the CML with high aspect ratio is demanded. In this work, we report on facile solution-based processes (i.e., slot-die and needle coatings) to fabricate the CML using poly(methyl methacrylate) (PMMA). It is found that compared with needle coating, slot-die coating provides the CML with lower aspect ratio due to the wide spread of solution along the hydrophilic head lip. Although needle coating provides the CML with high aspect ratio, it requires a high precision needle array module. To demonstrate that the aspect ratio of CML can be enhanced using slot-die coating, we have varied the molecular weight of PMMA. We can achieve the CML with higher aspect ratio using PMMA with lower molecular weight at a fixed viscosity because of the higher concentration of PMMA solute in the solution. We have also shown that the aspect ratio of CML can be further boosted by coating it repeatedly. With this scheme, we have fabricated the CML with the width of 252 ㎛ and the thickness of 5.95 ㎛ (aspect ratio=0.024). To visualize its light diffusion property, we have irradiated a laser beam to the CML and observed that the laser beam spreads widely in the vertical direction of the CML.