• 대한금속재료학회지
• /
• 제49권8호
• /
• pp.635-641
• /
• 2011

The effect of high shear speed on shear force, shear energy and fracture surface was investigated for the solder joint of a $Sn-_{3.0}Ag-_{0.5}Cu$ ball. For both ENIG and OSP pads, the shear force increased with an increase in shearing speed to 0.3 m/s. However, for an ENEPIG pad, the shear force increased with an increase in shear speed to 0.6 m/s and kept almost constant afterward. The shear energy decreased with an increase in shearing speed for ENIG and OSP pads. For the ENEPIG pad, however, the shear energy almost remained constant in a shearing speed range 0.3-3.0 m/s. The fracture mode analysis revealed that the amount of brittle fracture for the ENIG and the OSP pads increased with shearing speed, and a complete brittle fracture appeared at 1.0 m/s for ENIG and 2.0 m/s for OSP. However, the ENEPIG pad showed only a ductile fracture until 0.25 m/s, and a full brittle fracture didn't occur up to 3.0 m/s. The fracture mode matched well with the shear energy. The results from the high speed shear test of SAC305 were similar to those of SAC105.

• 마이크로전자및패키징학회지
• /
• 제31권1호
• /
• pp.35-42
• /
• 2024

최근 반도체 칩의 소형화 및 고집적화에 따라 미세 피치에 의한 범프 브리지 (bump bridge) 현상이 문제점으로 주목받고 있다. 이에 따라 범프 브리지 현상을 최소화할 수 있는 Cu pillar bump가 미세 피치에 대응하기 위해 반도체 패키지 산업에서 널리 적용되고 있다. 고온의 환경에 노출될 경우, 접합부 계면에 형성되는 금속간화합물(Intermetallic compound, IMC)의 두께가 증가함과 동시에 일부 IMC/Cu 및 IMC 계면 내부에 Kirkendall void가 형성되어 성장하게 된다. IMC의 과도한 성장과 Kirkendall void의 형성 및 성장은 접합부에 대한 기계적 신뢰성을 약화시키기 때문에 이를 제어하는 것이 중요하다. 따라서, 본 연구에서는 CS(Cu+ Sn-1.8Ag Solder) 구조 Cu pillar bump의 등온 시효 처리에 따른 접합부 특성 평가가 수행되었으며 그 결과가 보고되었다.

• 한국공작기계학회논문집
• /
• 제16권5호
• /
• pp.134-139
• /
• 2007

This paper presents a computer-based analysis on the thermal shock characteristics of Pb-free solder joints and UBM in flip chip assemblies. Among four types of popular UBM systems, TiW/Cu system with 95.5Sn-3.9Ag-0.6Cu solder joints was chosen for simulation. A simple 3D finite element model was first created only including silicon die, mixture between underfill and solder joints, and substrate. The displacements due to CTE mismatch between silicon die and substrate was then obtained through FE analysis. Finally, the obtained displacements were applied as mechanical loads to the whole 2D FE model and the characteristics of flip chip assemblies were analyzed. In addition, based on the hyperbolic sine law, the accumulated creep strain of Pb-free solder joints was calculated to predict the fatigue life of flip chip assemblies under thermal shock environments. The proposed method for fatigue life prediction will be evaluated through the cross check of the test results in the future work.

• 한국재료학회지
• /
• 제9권10호
• /
• pp.1018-1024
• /
• 1999

Sn-3.5Ag 무연합금을 Cu 및 Alloy42 리드프레임에 납땜접합 (solder joint)하고 미세조직, 젖음성, 전단강도, 시효효과를 측정하여 비교하였다. Cu의 경우, 땜납의 Sn기지상안에 Ag(sub)3Sn과 Cu(sub)6Sn(sub)5상이, 그리고 땜납/리드프레임의 경계면에서는 1∼2㎛ 두께의 Cu(sub)6Sn(sub)5상이 형성되었다. Alloy42의 경우, 기지상내에 있는 낮은 밀도의 Ag(sub)3Sn상만이, 그리고 계면에는 0.5∼1.5㎛ 두께의 FeSn(sub)2이 형성되었다. 한편, Cu에 비해 Alloy42 리드프레임에서 퍼짐면적은 크고 접촉각은 작아 더 우수한 젖음성을 나타내었으나, 전단강도는 35%, 연신율은 75%로 낮았다. 180℃에서 1주일간 시효처리 후, Cu 리드프레임에는 계면에 η-Cu(sub)6Sn(sub)5 층외에 ξ-Cu(sub)3Sn층이 성장하였고, Alloy42 리드프레임에는 기지상내에 Ag(sub)3Sn이 구형으로 조대하게 성장하였고, 계면에는 FeSn(sub)2층만이 약 1.5㎛로 성장하였다.

• Progress in Superconductivity
• /
• 제14권1호
• /
• pp.1-10
• /
• 2012

We fabricated a closed coils by using resistive-joint method and the joint resistance of the coils were estimated by field decay technique in liquid nitrogen. We used the Runge-kutta method for the numerical analysis to calculate the decay properties. The closed coil was wound by $(Bi,Pb)_2Sr_2Ca_2Cu_3O_x$/Ag tape. Both ends the tape were overlapped and soldered to each other. The current was induced in a closed coils by external magnetic flux density. Its decay characteristic was observed by means of measuring the magnetic flux density generated by induced current at the center of the closed coil with hall sensor. The joint resistance was calculated as the ratio of the inductance of the loop to the time constants. The joint resistances were evaluated as a function of critical current of loop, contact length, sweep time, and external magnetic flux density in a contact length of 7 cm. It was observed that joint resistance was dependent on contact length of a closed coil, but independent of critical current, sweep time, and external magnetic flux density. The joint resistance was measured to be higher for a standard four-probe method, compared with that for the field decay technique. This implies that noise of measurement in a standard four-probe method is larger than that of field decay technique. It was estimated that joint resistance was $8.0{\times}10^{-9}{\Omega}$ to $11.4{\times}10^{-9}{\Omega}$ for coils of contact length for 7 cm. It was found that 40Pb/60Sn solder are unsuitable for persistent mode.

• 마이크로전자및패키징학회지
• /
• 제17권4호
• /
• pp.11-17
• /
• 2010

차세대 패키징 기술을 실현하기 위해서는 극복해야 할 기술적인 과제들이 많이 존재한다. 그 중에서 솔더 접합부의 EM에 의한 고장은 오랜전부터 알려진 과제이지만, 고밀도화, 파인핏치화, 발열문제가 심각해지면서 현실적인 문제로 인식되기 시작했다. 더욱이 솔더가 무연화 되면서 다양해진 구성원소들의 영향에 대한 연구가 시작되었다. 지금까지의 연구결과를 종합해보면 Sn-Pb 공정솔더 보다 무연솔더는 EM에 대한 저항성이 강한 것으로 보여진다. 하지만, 무연솔더 접합부에서 발생하는 EM현상에 대해서는 아직 밝혀지지 않은 부분이 많다. 보이드의 핵 생성 및 성장속도와 전기저항의 급격한 변화와의 관계, Sn 결정립의 방향과 전류밀도에 따른 마이그레이션 속도계수와 수명예측기술, 각종 무연솔더와 시험조건에서의 언더필의 효과 등에 관한 다양한 연구가 필요하다. 또한 무연 플립칩 패키지의 총체적인 신뢰성 확보를 위해, EM과 반도체칩 내부배선의 발열에 기인하는 Thermomigraton, 응력에 기인하는 Stress-migration과의 상관관계에 대한 연구도 요구된다.

• Journal of Welding and Joining
• /
• 제33권3호
• /
• pp.25-31
• /
• 2015

Due to environmental regulations (RoHS, WEEE and ELV) of the European Union, electronics and automotive electronics have to eliminate toxic substance from electronic devices and system. Specifically, reliability issue of lead-free solder joint have an increasing demand for the car electronics caused by ELV banning. The authors prepared engine control unit and cabin electronics soldered with Sn-3.0Ag-0.5Cu (SAC305). To compare with the degradation characteristics of solder joint strength, thermal cycling test (TC), power-thermal cycling test (PTC) and series tests were conducted. Series tests were conducted for TC and PTC combined stress test using the same sample in sequence and continuously. TC test was performed at $-40{\sim}125^{\circ}C$ and soak time 10 min for 1000 cycles. PTC test was applied by pulse power and full function conditions during 100 cycles. Combined stress test was tested in accordance with automotive company standard. Solder joint degradation was observed by optical microscopy and environment scanning electron microscopy (ESEM). In addition, to compare with deterioration of bond strength of quad flat package (QFP) and chip components, we have measured lead pull and shear strength. Based on the series test results, consequently, we have validated of series test method for lifetime and reliability of Pb-free solder joint in automotive electronics.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2009년도 춘계학술대회 논문집
• /
• pp.194-195
• /
• 2009

본 연구에서는 고속전단 강도에 표면 처리의 변화가 미치는 영향에 대해 연구하고자 하였다. 표면 처리를 ENIG, ENEPIG, OSP로 하여 고속전단시험을 수행하였다. 고속전단 결과 SAC105의 전단 강도 값은 ENIG가 가장 작았고, ENEPIG가 가장 높았다. SAC305의 전단 강도 값은 ENIG가 가장 작았고, OSP와 ENEPIG는 비슷한 값을 나타냈다.

• 마이크로전자및패키징학회지
• /
• 제16권1호
• /
• pp.33-38
• /
• 2009

전자 기기 제품들이 소형화 및 휴대화 되면서 낙하충격 신뢰성에 대한 관심이 높아지고 있다. 본 연구에서는 대표적인 무연솔더인 Sn-3.0Ag-0.5Cu 솔더를 이용하여 ENIG (Electroless Nickel Iimmersion Gold), OSP (Organic Solderability Preservative) 표면 처리와 등온 시효 시험 (High Temperature Storage test)에 따른 보드 레벨 패키지 (board level package)의 낙하충격 신뢰성 (drop reliability) 시험을 수행하였다. 또한 충격 조건을 변화시켜 시편에 가해지는 가속도 (G:acceleration)와 충격 지속 시간 (pulse duration)에 따른 신뢰성을 평가하였다. 기판의 strain측정 결과 중앙 부위가 가장 응력이 컸으며, 충격가속도에 비례하여 응력이 증가하였다. 시효 처리 전에는 OSP처리된 기판이 다소 우수한 신뢰성을 보였지만, 시효 처리후에는 ENIG기판에서 신뢰성이 우수하였고, 반대로 OSP는 감소하는 경향을 보였다. OSP의 경우 과도한 금속간화합물 (intermetallic compound)의 성장으로 인해 접합 계면에서 취성파괴 (brittle fracture)가 일어난 것을 관찰할 수 있었다.

• 마이크로전자및패키징학회지
• /
• 제12권1호
• /
• pp.65-71
• /
• 2005

At present, Electronic industries push ahead to eliminate the Pb(Lead) -a hazardous material-from all products. Especially, we have performed to select the optimum standard composition of lead free alloy for the application to products for about 3 years from 2000. These days, we have the chance for applying to the mass-production. This project constructed the system for applying the lead free solders on consumer electronic products, which is one of the major products of the LG Electronics. To select the lead free solders with corresponding to the product features, we have passed through the test and applied with Sn-3.0Ag-0.5Cu alloy system to our products, and for the application to the high melting temperature composition, we secured the thermal resistance of the many parts and substrate and optimized the processing conditions. We have operated the temperature cycling test and the high temperature storage test under the standards to confirm the reliability of the products. On these samples, we considered the consequence of our decision by the operating test. For the long life time of the product, we have operated the temperature cycling test at $-45^{\circ}C\;-\;+125^{\circ}C$, 1 cycle/hour, 1000 cycles. Also we have tested the tin whisker growth about lead free plating on lead finish. We have analyzed with the SEM, EDS and any other equipment for confirming the failure mode at the joint and the tin whisker growth on lead free finish.