• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 춘계학술대회 논문집
• /
• pp.918-921
• /
• 2002

Some investigators who have tried to achieve the highly smooth surface finish using electrochemical processes have reported that high current density produced lustrous surfaces while the opposite conditions produced a passive layer and had a tendency to produce a black surface. However, processing at a low current density may produce a non-lustrous surface but the improvement of dimensional accuracy of the surface is significant. The surface with pulse process was a bit more lustrous than with continuous current but the black passive layer still could be found at grooved surface. There are two ways to achieve highly smooth surface finish. One is brushing it with a brush the other is electrochemical machining (ECM) with high current. The former method is the most common polishing practice, but not only may the surface obtained differ from operator to operator, but precision smooth surface on micro grooves are difficult to obtain. The latter one recently has been used to produce a highly smooth surface after EDM process. However, the material removal rate in ECM with high current is relatively high. Hence the original shape of the micro grooves, which was formed by electrochemical micro-machining (EMM) process, may be destroyed. In this study, an electrochemical polishing process using pulse current is adopted as a possible alternative process when micro grooves formed by EMM process should be polished. Mirror-like micro grooves with lustrous and smooth surface can be produced electrochemically with pulse current because the voltage and current used can be lower than the case of continuous current. This study will discuss the accurate control of physical and electrical conditions so as to achieve mirror-like micro grooves with lustrous and smooth surface without destroying the original shape of micro grooves.

• Design & Manufacturing
• /
• 제13권3호
• /
• pp.19-23
• /
• 2019

In the mold industry, CAM software has been introduced to solve the impossible or time-consuming part of the mold industry because the increase in labor costs, the drop in mold price, and the short delivery time are tasks to be solved not only in the manufacturing industry but also in the mold industry as a whole. In order to reduce the processing time and improve the surface roughness, we have been conducting various researches for efficient machining. This study was carried out to compare the ball end mill and radius end mill tools with the Power mill software and NC brain software under the same conditions and to find out the most efficient method of machining the smooth drafting surface and improving the surface roughness. (1) By machining the smooth drafting surface using radius end mill, the machining time is 23.7% faster than when using ball end mill. (2) Surface roughness when machined with radius end mill is smoother than when using ball end mill. Based on these results, it can not be applied to all shapes, but if it is a relatively wide and simple gradient shape, the raster machining method using radius end mill can be more effective in terms of delivery and quality than machining with ball end mill.

• The Journal of Advanced Prosthodontics
• /
• 제6권2호
• /
• pp.96-102
• /
• 2014

PURPOSE. This study was performed to characterize the effects of zirconia coated with calcium phosphate and hydroxyapatite compared to smooth zirconia after bone marrow-derived osteoblast culture. MATERIALS AND METHODS. Bone marrow-derived osteoblasts were cultured on (1) smooth zirconia, (2) zirconia coated with calcium phosphate (CaP), and (3) zirconia coated with hydroxyapatite (HA). The tetrazolium-based colorimetric assay (MTT test) was used for cell proliferation evaluation. Scanning electron microscopy (SEM) and alkaline phosphatase (ALP) activity was measured to evaluate the cellular morphology and differentiation rate. X-ray photoelectron spectroscopy (XPS) was employed for the analysis of surface chemistry. The genetic expression of the osteoblasts and dissolution behavior of the coatings were observed. Assessment of the significance level of the differences between the groups was done with analysis of variance (ANOVA). RESULTS. From the MTT assay, no significant difference between smooth and surface coated zirconia was found (P>.05). From the SEM image, cells on all three groups of discs were sporadically triangular or spread out in shape with formation of filopodia. From the ALP activity assay, the optical density of osteoblasts on smooth zirconia discs was higher than that on surface treated zirconia discs (P>.05). Most of the genes related to cell adhesion showed similar expression level between smooth and surface treated zirconia. The dissolution rate was higher with CaP than HA coating. CONCLUSION. The attachment and growth behavior of bone-marrow-derived osteoblasts cultured on smooth surface coated zirconia showed comparable results. However, the HA coating showed more time-dependent stability compared to the CaP coating.

• 설비공학논문집
• /
• 제23권7호
• /
• pp.498-504
• /
• 2011

As the electronic industry rapidly develops, the heat flux from state-of-the-art electronics increases up to $10^6\;W/m^2$. For this reason, the development of a new cooling technology for high heat flux applications is strongly required. Recently, some cooling technologies using boiling and condensation of working fluid are being adopted to overcome such a technical barrier. In the present study, a smooth boiling surface ($14{\times}14\;mm^2$) was immersed in FC-72 and its vapor was condensed by four different types of condensation surfaces ($30{\times}30\;mm^2$ base). The condensing surfaces were composed of a smooth surface and $1{\times}1\;mm^2$ pin-finned surfaces of 2 mm height with 0.3, 0.5 and 1 mm array spacing. Boiling and condensing characteristics were investigated in detail on their combinations of boiling and condensing surfaces. For a smooth boiling surface the results obtained showed that the pin-finned condensing surface with 1 mm array spacing yielded the best performance and the smooth condensation surface did the worst. Furthermore hysteresis phenomena could be reduced by using enhanced condensing surfaces.

• 대한치과보존학회:학술대회논문집
• /
• 대한치과보존학회 2003년도 제120회 추계학술대회 제 5차 한ㆍ일 치과보존학회 공동학술대회
• /
• pp.617-617
• /
• 2003

I. Objectives This study was done to evaluate whether or not there are any differences in microleakage of the class 5 composite restoration that were filled at the smooth surface and the proximal surface respectively. In addition any differences between small and large-sized restoration were also studied. II. Materials and Methods Total sixty-four class 5 resin restorations, sixteen per group, were made in the permanent teeth. Two-sized cavities, small ($2{\;}{\times}{\;}2{\;}{\times}{\;}1.5{\;}mm$) and large ($4{\;}{\times}{\;}2{\;}{\times}{\;}1.5{\;}mm$), were filled at the smooth surface and the proximal surface each.(omitted)

• Carbon letters
• /
• 제10권2호
• /
• pp.97-100
• /
• 2009

In this work, effects of carbon matrix on sliding friction and wear behavior of four kinds of C/C have been investigated against 40 Cr steel ring mate. Composite A with rough lamination carbon matrix (RL) shows the highest volume loss and coefficient of friction, while composite D with smooth lamination/resin carbon matrix (SL/RC) shows the lowest volume loss. The worn surface of composite A appears smooth, whereas that of composite C with smooth lamination carbon (SL) appears rough. The worn surface of composite D appears smooth under low load but rough under high load. Atomic force microscope images show that the size of wear particles on the worn surface is also dependent on the carbon matrix.

• 기계저널
• /
• 제16권2호
• /
• pp.122-127
• /
• 1976

It was reported in the Journal of KSME Vol. 15, No. 3 and No. 4, 1975 that could be finished the best smooth surface by applying frictional work to the metal surface. Even if we can finish the best smooth surface of methal, it is not available when it has not anti-wear. Present study tried to investigate the anti-wear and the characteristics of frictional worked surface by using the sliding contact between plain bearing of brass and frictional worked jornal of mild steel. The results were compared with the case of ground journal.

• International Journal of CAD/CAM
• /
• 제12권1호
• /
• pp.29-37
• /
• 2012

A new algorithm has been developed to construct surface from the contours having branches and the final smooth surface is obtained by the reversible Catmull-Clark subdivision. In branching, a particular layer has more than one contour that correspond with at least one contour at the adjacent layer. In the next step, three-dimensional composite curve is constructed from contours of a layer having correspondence with at least one contour at the adjacent layer by inserting points between them and joining the contours. The points are inserted in such a way that the geometric center of the contours should merge at the center of the contours at the adjacent layer. This process is repeated for all layers having branching problems. Polyhedra are constructed in the next step with the help of composite curves and the contours at adjacent layer. The required smooth surface is obtained in the proposed work by providing the level of smoothness.

• 대한치과보철학회지
• /
• 제38권1호
• /
• pp.108-115
• /
• 2000

This study was designed to compare the effect of polishing on surface roughness of composite resin. We used Z100(3M) composite resin and placed the composite resin in the hole (4mm thick and 4mm in diameter) of vinyl plate and polymerized it under manufacturer's instructions. Samples were divided into 5 groups by polishing methods. Group 1 was control: resin was polymerized under glass plate, Group 2: resin was polymerized without any polishing procedure, Group 3: resin was polymerized with a polishing procedure of abrasive disc, Group 4: bonding agent was applyed in thin layer and polymerized on the polished polymerized resin surface. Group 5: resin was polymerized under transparent celluloid strip. The surface roughness of each specimen was measured with Sufacoder SEF-30D (Kosaka lab. Ltd) under 0.08mm cut off, 0.05mm/s stylus speed, ${\times}40$ horizontal magnification, ${\times}5000$ vertical magnification. The results were as follows : 1. Group 1 showed the most smooth surface in this study. 2. Group 3 showed more rough surface than Group 2. Considering the surface roughness, it would be better to make the shape completely before polymerize the resin. To finish and polish after the polymerization of resin makes less smooth surface. 3. When we use the transparent celluloid strip, minimum finishing procedures are recommended. Any polishing procedure could not recover the smooth resin surface of celluloid strip. 4. Application and polymerization of the thin layer of bonding agent on the polished surface showed the minimum surface smoothing effect.

• 한국정밀공학회지
• /
• 제26권12호
• /
• pp.117-122
• /
• 2009

The hexagonal network-type PDMS microstructures were fabricated and they were employed to low-friction drag surfaces. While the lowest contact angle measured from the smooth surface was $108^{\circ}$ the highest contact angle measured from the microstructured surfaces was $145^{\circ}$ The moving speed of bullet-type capsule attached with a PDMS pad of smooth surface ($CA=108^{\circ}$) was 0.1261 m/s and that with a PDMS pad of microstructured surface ($CA=145^{\circ}$) was 0.1464 m/s. Compared with the smooth surface, the microstructured surface showed 16.1% higher moving speed. The network-type microstructures have a composite surface that is composed with air and PDMS solid. Therefore, the surface does not wet: rather water is lifted by the microstructures. Because of the composite surface, water shows slip-flow on the microstructures, and thus friction drag can be reduced.