• Journal of Korea Ship Safrty Technology Authority
• /
• s.24
• /
• pp.4-20
• /
• 2008

Stainless steel 304 or stainless steel 630 types using propeller shaft of a small ship or a FRP fishing boat generally restrain localization corrosion and abrasion damage occurrence to shaft bearing or grand packing contact. In general, the residual stress which remains after welding or heat treatment in material can cause the stress concentration or localization corrosion. In case of small ship, stainless steel such as STS304 has long been used for propeller shaft. Meanwhile, crew of small ship tend to reuse damaged propeller shaft after repair by welding and performing heat treatment to save cost. However, it was found that reused propeller shaft by repair often caused troubles in ship's operation. In this study, the basic guideline for maintenance and treatment of propeller shaft are investigated. From the results of investigation, remarkable deterioration of the material properties and corrosion resistance on the welded work part was observed.

• Korean Journal of Computational Design and Engineering
• /
• v.7 no.4
• /
• pp.254-261
• /
• 2002

Small marine propeller is generally machined by 5-axis machining. This paper suggests a method to create geometric model from point array data and 4-axis machining NC data for propeller. With conventional method, the setting posture should be changed, because propeller has front and back surface of wing. The change of setting posture has a bad influence on precision of propeller. So this paper pro-poses a method to machine propeller by single setup for 4-axis machining. The cutter moves to parallel direction of the XY plane. To determine the cutter orientation efficiently, the' tilting guiding line' is proposed. A proposed algorithm is written in C language and successfully applied to the 5-axis milling machine of industrial field.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.9 no.6
• /
• pp.655-667
• /
• 2017

The results of a numerical study on the performance of a propeller operating near a free surface are presented. The numerical simulations were performed for the various advance coefficients and the submergence depths of the model propeller. The effects of the model propeller size were investigated using two different model propeller sizes for all cases. The wave pattern of the free surface and the flow structure around the propeller as well as the hydrodynamic characteristics of the propeller were investigated through simulation results. The thrust and torque fluctuated and the trajectory of the tip vortex was distorted due to the interaction with the free surface. The wave pattern of the free surface was related to the tip vortex of the propeller. The decreases in thrust and torque at the small model propeller were greater than those of the large model propeller. The reduction rate of the thrust and torque increased with the advance coefficient.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.20 no.4
• /
• pp.1491-1500
• /
• 1996

Unstable performance deterioration was found on the performance curve of a small propeller fan with a back plate. To investigate this phenomenon and the effects of the back-plate on the performance of the fan, performance tests and flow measurement using 3-hole pitot tube were carried out. Measurements showed that when the flow rate is small, the radial flow dominates, and when the flow rate is large, the axial flow dominates. Performance characteristic of the propeller fan changes from radial to axial type as the flow rate increases. Unstable performance changes are the result of type change of the flow through the fan.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.2
• /
• pp.279-285
• /
• 2013

The feasibility of substituting a composite mold for an aluminum mold in the fabrication of a small ship propeller was investigated. A small three-blade aluminum propeller was used as a plug for manufacturing the composite mold. A GRPG composite mold and propeller were made from an unsaturated polyester resin, Epovia gelcoat, and woven and mat glass fibers using the compression and vacuum method at room temperature. The hardness and surface roughness and the strength and deformation of the compression and suction molds were experimentally determined. The results were compared with the ISO 484/2 standard and some aluminum alloy materials. The results showed that the deformation of the mold satisfied the tolerance of the thickness of the blade. Some characteristics of the GRPG composite mold were better than those of the aluminum alloy mold (surface smoothness, weight, performance, and cost), and some characteristics were similar (detachment ability and life-cycle). Therefore, the composite mold is considered suitable for the fabrication of a small composite ship propeller.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2001.05a
• /
• pp.173-179
• /
• 2001

The torsional or axial critical vibration of the order coinciding with the number of propeller blades is simultaneously excited by the harmonic tangential or radial forces acting on the crank shaft and by the harmonic of the same order from the propeller. The exciting torque of propeller is relatively small comparing with that of crank side, but the exciting force of propeller rather larger than that of crank shaft. With this situation, the exciting force of propeller cannot neglect if the axial vibration of propulsion shafting is calculated. With the propeller in its optimal angular position, i.e. its excitation effect opposed to that of the engine, the stresses at the critical revolution will largely cancel themselves out. In this paper, a method of optimizing the angular propeller position with regard to torsional and axial vibration is studied. The optimal relative angle is determined theoretically by calculation results of coupled torsional-axial vibration.

• Journal of Drive and Control
• /
• v.18 no.4
• /
• pp.43-51
• /
• 2021

In this study, we designed a hydraulic propulsion propeller system that allows dredged materials to be carried out by the dredger to the disposal place. The proposed model equation was used to formulate the screw propeller specifications considering the resistance to the dredger, and the quantitative specifications of the hydraulic propulsion propeller were determined through the numerical analysis programs. In addition, based on the proposed results, we were able to determine the specifications of the hydraulic system that was used for the hydraulic motor in the propulsion propeller device and then manufactured the hydraulic propulsion propeller. To guarantee the reliability of the proposed model equation, an external testing agency was invited and verified that the hydraulic propulsion propeller based on the proposed model equation could achieve the target speed in the dredger.

• Journal of the Semiconductor & Display Technology
• /
• v.17 no.1
• /
• pp.84-87
• /
• 2018

As the propeller end speed increases, the propeller surface is damaged in the process of bubble formation and dropout. It is intended to prevent the corrosion of the propeller by modifying the shape of the end through the winglet structure to mitigate the cavitation phenomenon. In the case of conventional SUS materials, the cost of production is so high that plastic materials are used to prevent corrosion. This paper aims to mitigate the cavitation by deforming the shape of the end through the winglet structure by using the SMC composite material of the propeller using the existing SUS.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.21 no.6
• /
• pp.790-798
• /
• 2018

Discrete noise signals from a small scale tactical unmanned aerial vehicle(UAV) propeller were predicted numerically using time domain approach. Two-bladed 29 inch propeller in diameter and 150 kgf in gross weight were used for main parameters of the UAV based on the actual size of the similar scale vehicle. Panel method and Farassat formula A1 were adopted for aerodynamic and aeroacoustic analysis respectively. Time domain signals of both thickness and loading noises were transformed into frequency domain to analyze the discrete noise characteristics. Directivity pattern in a plane perpendicular to the rotating disc plane and attenuation of noise intensity according to double distance were also presented.

• Transactions of the Korean hydrogen and new energy society
• /
• v.14 no.2
• /
• pp.171-176
• /
• 2003

The propeller type hydro turbine model with vertical axis has been tested and analyzed. The blade angle of turbine model were designed to be varied according to the condition of head and flowrate. When the changes in head and output were comparatively large, the efficiency drop were small, so the efficiency characteristics and stability of the entire operating condition were maintained in good condition. These results showed that the developed model in this study will be suitable for small hydro power stations with large changes in head and load such as sewage treatment plants and agricultural reservoirs.