• Journal of Mechanical Science and Technology
• /
• 제18권6호
• /
• pp.972-978
• /
• 2004

Forward slip is an important parameter often used in rolling-speed control models for tandem hot strip rolling mills. In a hot strip mill, on-line measurement of strip speed is inherently very difficult. Therefore, for the set-up of the finishing mill, a forward slip model is used to calculate the strip speed from roll circumferential velocity at each mill stand. Due to its complexity, most previous researches have used semi-empirical methods in determining values for the forward slip. Although these investigations may be useful in process design and control, they do not have a theoretical basis. In the present study, a better forward slip model has been developed, which provides for a better set-up and more precise control of the mill. Factors such as neutral point, friction coefficient, width spread, shape of deformation zone in the roll bite are incorporated into the model. Implementation of the new forward slip model for the control of a 7-stand hot strip tandem rolling mill shows significant improvement in roll speed set-up accuracy.

• 한국자동차공학회논문집
• /
• 제14권6호
• /
• pp.89-94
• /
• 2006

The tire delivering power generated from engine to the ground pulls a vehicle to move. Radius of tires is changeable due to elasticity that depends on the speed of vehicle and traction force. The main objectives on this study are real time measurement of dynamic radius and slip ratio according to the speed and traction force. The dynamic radius is proportional to speed and traction force. According to measurement, the dynamic radius is increased about 3mm under 100km/h compared to stop. It is also increased about 1.5mm when a traction force is supplied as much as 4kN compared to no load state at low speed. There is no strong relationship between slip ratio and vehicle speed. The slip ratio is measured up to 4% under WOT at first stage gear. Through this research, the method of measuring dynamic radius and slip ratio is set up and is expected to be applied to the measurement of traction force in chassis dynamometer or accelerating and climbing ability.

• 한국터널지하공간학회 논문집
• /
• 제21권6호
• /
• pp.811-823
• /
• 2019

최근에는 수직구 구조물 시공방법으로 현장타설 공법 대비 시공속도가 빠르며, 안전하고 경제적인 연속상승 슬립폼 공법이 다수의 현장에 적용되고 있다. 슬립폼 공법으로 시공 가능한 높이는 2.5~4 m/day로 알려져 있는데, 콘크리트 온도가 10~30℃의 범위 밖에서는 강도 변화나 탄성 특성의 변화에 미치는 영향이 크므로 동절기 공사에서는 3 m/day 이상의 시공속도를 내기가 어렵다. 또한, 콘크리트는 수화 작용으로 인해 수화열이 발생하는데, 이는 콘크리트의 온도 균열을 초래한다. 따라서 슬립폼 연속상승시 콘크리트의 온도 제어 양생이 필요하며, 본 연구에서는 히팅 패널 및 시험용 연속상승 장치를 개발하여 반발경도, 초음파 전파시간, 수화열 및 외부온도를 측정하였다. 이를 기반으로 히팅슬립폼을 제작하였으며, "김포 현장"과 "신월 현장"에 히팅슬립폼을 적용하였다. 김포현장은 주간(08:00~17:30) 평균 1.9 m/day 또는 0.200 m/hr, 신월 현장은 2.0 m/day 또는 0.210 m/hr를 목표 상승속도 값으로 비교하였다.

• 한국자동차공학회논문집
• /
• 제17권3호
• /
• pp.74-80
• /
• 2009

The objective of this paper was to investigate the slip rate and the slip frequency number of damper clutch of torque converter in 2.4L passenger vehicle with 5-speed A/T and analyze the effect of slip control and control strategy on driving characteristics and the fuel economy. The newly developed torque converter with the more durable wet friction material and the slip-controlled damper clutch system, the DCC system, was installed, which was easily compatible and amendable of the lock-up clutch of the base system. The vehicle has been tested on the fuel economy modes such as FTP-75, HWFET and NEDC (ECE15+EUDC) driving cycle at chassis dynamometer. The DCC mode (II), of which the control strategy had both the lock-up and the slip-controlled clutch, and the DCC mode (I) with full slip-controlled clutch were compared with the base system with only the lock-up clutch. As the research result, comparison to base system, the fuel consumption of the vehicle with the DCC control (II) was effectively improved by 6.6% and 7.7% on FTP-75 and NEDC mode.

• 대한토목학회논문집
• /
• 제31권4A호
• /
• pp.295-302
• /
• 2011

초장대교 콘크리트 고주탑 시공시에 사용되고 있는 슬립폼 시스템의 상승속도를 결정하는 요소인 초기경화시간은 콘크리트가 거푸집에서 안전하게 빠져나올 수 있는 굳기를 갖게 되는 콘크리트 타설 후 경화시간으로서, 배합 시 단위시멘트량 및 타설시 여러 현장 환경에 크게 영향을 받으므로, 콘크리트 타설 전에 초기경화시간을 정확히 파악하는 것은 매우 어렵다. 따라서 슬립폼 시스템의 안전성 확보 및 콘크리트면의 유지관리 문제가 발생하지 않도록 초기경화시간 결정을 위한 콘크리트 경화정도를 파악하는 기술이 필요하다. 더구나 슬립폼 공법은 연속적인 시공이 이루어지므로 거푸집 탈형 전 콘크리트의 경화정도를 연속적으로 파악할 수 있어야 한다. 초음파를 이용한 기법은 콘크리트면에 초음파를 투과시켜 투과된 신호를 측정 및 분석하는 방법으로 정량적이며 연속적으로 콘크리트의 경화정도를 파악할 수 있다. 특히 표면파 속도를 이용하는 기법은 표면을 따라 전파하는 표면파의 특성을 이용한 것으로서 표면파 속도의 변화를 통해 콘크리트 경화정도를 알 수 있으며, 주탑과 같이 두께가 두꺼운 콘크리트 구조물에 적용이 적합하다. 따라서 본 논문에서는 표면파 속도를 이용하여 콘크리트의 경화정도를 추정함으로서 슬립폼 시스템의 상승속도를 결정하는 연구를 수행하였다. 먼저 슬립폼 시스템 상승속도와 초기경화시간과의 관계식을 유도하였으며, 표면파 진행문제의 수치해석 결과를 연속웨이블릿변환 하여 표면파 속도를 추정하였다. 이때 탄성파 발생위치와 두 개의 수신점 거리에 따른 추정된 표면파 속도의 정밀도를 조사하였으며, 추정된 표면파 속도와 탄성계수와의 관계를 조사하였다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1999년도 제3회 압연심포지엄 논문집 압연기술의 미래개척 (Exploitation of Future Rolling Technologies)
• /
• pp.47-56
• /
• 1999

New rolling speed prediction model has been developed for the precise presetting rolling speed of each finishing mill stand in the tandem hot strip mill. Those factors such as neutral point, work roll diameter, rolling torque, friction coefficient, bite angle and the thickness at each side of entry and deliver of the rolls were taken into account. To consider width effect on forward slip, calibration factors obtained from rolling torque has been added to new prediction model and refining method has also been developed to reduce the speed unbalance between adjacent stands. The application of the new model showed a good agreement in rolling speeds between the predictions and the actual measurements, and the standard deviation of prediction error has also been significantly reduced.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2004년도 학술대회지
• /
• pp.221-231
• /
• 2004

A kinetic theory analysis is made of low-speed gas flows in a microfluidic system consisted of three microchannels in series. The Boitzmann equation simplified by a collision model is solved by means of a finite difference approximation with the discrete ordinate method. For the evaluation of the present method results are compared with those from the DSMC method and an analytical solution of the Navier-Stokes equations with slip boundary conditions. Calculations are made for flows at various Knudsen numbers and pressure ratios across the channel. The results compared well with those from the DSMC method. It is shown that the analytical solution of the Navier-Stokes equations with slip boundary conditions which is suited fur fully developed flows can give relatively good results. In predicting the geometrically complex flows up to a Knudsen number of about 0.06. It is also shown that the present method can be used to analyze extremely low-speed flow fields for which the DSMC method is Impractical.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.24-25
• /
• 2006

High-Speed Centrifugal Compaction Process is one of slip-using compacting method originally developed for processing of oxide ceramics. In this study, we apply the HCP to ultra-fine (0.1 micron) WC powder. Organic liquid of heptane was chosen as dispersing media to avoid possible oxidation of WC. The mixing apparatus was a key to obtain dense compacts. Only the slips mixed by high energy planetary ball mill were packed up to 55% by the HCP, and sintered to almost full density at 1673 K without any sintering aids. This sintered compact marked Vickers hardness of Hv 2750 at maximum.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1995년도 하계학술대회 논문집 A
• /
• pp.9-11
• /
• 1995

In order to achieve a essential requirement for the driving system of electric vehicles, that is, starting pick-up ability, a wound-type induction motor with double-rotor structure is proposed. Slip Power Recovery system is adopted to improve the efficiency in the low speed range and to control speed of this system. Theoretical analysis and experimental results from 300[W] prototype motor is presented to verify the improvement of pick-up ability and high-efficiency driving characteristics through the wide speed range, especially under the low speed range.

• 항공우주시스템공학회지
• /
• 제7권2호
• /
• pp.23-28
• /
• 2013

This is a research on the method of how to improve lateral stability for the small general aviation airplane to meet the FAR part 23 requirements. This research is based on the experience of certification flight tests of KC-100 airplane for Korea first type certification. KAS/FAR Part 23.177 is the static lateral and directional stability requirement. And, 23.177(b) requires to show the tendency to raise the low wing in steady heading side slip maneuver. However, it is very difficult for the low wing to be raised at the low speed during the steady heading side slip maneuver. So, the requirement allows not be negative at the $1.2V_{S1}$ speed and takeoff configuration. (static stability requirement requires low wing picked up at any speed except $1.2V_{S1}$ speed and takeoff configuration) In this paper, the static lateral stability requirements and the lessons & learned of KC-100 airplane certification flight test results are shown.