• Steel and Composite Structures
• /
• 제25권4호
• /
• pp.473-484
• /
• 2017

In this study a seismic retrofit scheme for a building structure was presented using steel plate slit dampers. The energy dissipation capacity of the slit damper used in the retrofit was verified by cyclic loading test. Genetic algorithm was applied to find out the optimum locations of the slit dampers satisfying the target displacement. The seismic retrofit of the model structure using the slit dampers was compared with the retrofit with enlarging shear walls. A simple damper distribution method was proposed using the capacity spectrum method along with the damper distribution pattern proportional to the inter-story drifts. The validity of the simple story-wise damper distribution procedure was verified by comparing the results of genetic algorithm. It was observed that the capacity-spectrum method combined with the simple damper distribution pattern leaded to satisfactory story-wise distribution of dampers compatible with the optimum solution obtained from genetic algorithm.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.182-184
• /
• 2004

This paper presents a PI controller tuning method for high performance permanent magnet synchronous motor (PMSM) drives under load variations using clustering fuzzy algorithm. In many speed tracking control systems PI controller has been used due to its simple structure and easy of design. PI controller, however, suffers from the electrical machine parameter variations and disturbances. In order to improve the tracking control performance under load variations, the PI controller parameters are modified during operation by clustering fuzzy method. This method based on optimal fuzzy logic system has simple structure and computational simplicity. It needs only sample data which is obtained by optimal controller off-line. As the sample data implemented in the adaptive fuzzy system can be modified or extended, a flexible control system can be obtained Simulation results show the usefulness of the proposed controller.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년 학술대회 논문집 정보 및 제어부문
• /
• pp.136-138
• /
• 2006

Recently, network systems are widely used in several areas, and some considerable attentions have been directed to the Networked Control System(NCS). In NCS, network-induced delays are inevitable, and they sometimes degrade the performance of networked control systems to be a source of potential instability. In this paper, We proposes a compensation method for networked control system subject to network-induced delays by using a simple method, which is based on a sort of predictive strategy. To evaluate its feasibility and effectiveness, a real-time NCS for a rotary inverted pendulum is implemented via an Ethernet. Based on the experimental results. we show that the proposed simple method can be a practical and feasible solution to NCS design.

• 전자공학회논문지D
• /
• 제34D권10호
• /
• pp.53-59
• /
• 1997

In this paper, we present a 20 GHz low-loss dual-mode channel filter designed by using mode matching method. The performance of dual-mode channel filter mainly depends on iris characteristics. Therefore the exact design of iris is the key point to get good frequncy response of the filter. MOde matching technique is widely used ot design several kinds of waveguide filters because it is simple in theory and can easily calculate the scattering matrices at the discontinuities with simple structure like iris coupled filters. Additionally the effect for finite thickness of the iris in the dual-mode cavity iflter is analyzed by te full-wave method, providing the exact filter implementation without trial and error.

• 한국CDE학회논문집
• /
• 제5권4호
• /
• pp.336-346
• /
• 2000

This paper presents a geometric method that can detect and compute all conic sections in the intersection of two tori. Conic sections contained in a torus must be circles. Thus, when two tori intersect in a conic section, the intersection curve must be a circle as well. Circles in a torus are classified into profile circles, cross-sectional circlet, and Yvone-Villarceau circles. Based on a geometric classification of these circles, we present a procedural method that can detect and construct all intersection circles between two tori. All computations can be carried out using simple geometric operations only: e.g., circle-circle intersections, circle-line intersections, vector additions, and inner products. Consequently, this simple structure makes our algorithm robust and efficient, which is an important advantage of our geometric approach over other conventional methods of surface intersection.

• International Journal of Concrete Structures and Materials
• /
• 제3권1호
• /
• pp.63-69
• /
• 2009

This paper provides the engineer with a simple design method dealing with situations arise where in-situ reinforced concrete joints are cast between hollow core units. Using finite element method, hollow core slabs with wide in-situ RC joints under point load and line loads are analysed. In addition, some important behavioural characteristics of the floor slab subjected to line and point loads are investigated. In-situ reinforced concrete joint causes reduction of load distribution for remote units because distance to the remote units from the point of load is increased, while the portion of load distribution carried by loaded unit increases. Also, it was turned out load distribution factors for point load and line loads are almost same. Finally, we suggest a simple analytical method, which can determine load distribution factors using normalized deflections by regression analysis for design purposes.

• 유공압시스템학회:학술대회논문집
• /
• 유공압시스템학회 2010년도 춘계학술대회
• /
• pp.81-85
• /
• 2010

This paper deals with the issue of motion control of a single rod cylinder-load system using simple adaptive control (SAC) method. Prior to controller design, the experiment of open-loop response has been performed. Based on it, design parameters of transfer function are obtained. The effect of parallel feedforward compensator has been investigated by computer simulation, suppressing the oscillatory motion. Through experiments it is conformed that the SAC method gives good tracking performance compared to the PD control method.

• 대한조선학회논문집
• /
• 제47권6호
• /
• pp.803-807
• /
• 2010

The transfer function method is a widely used in the analysis of underwater radiated noise of ships because it is simple to implement and gives a simple way in the design stage requiring trade-off studies on various kinds of noise sources. In this study, a framework is implemented based on the transfer function method. The framework is interfaced to a software providing transfer functions of hull force to underwater radiated noise. The transfer function-based underwater radiated noise analysis approach is reviewed and the implemented framework structure is described. As an example, a numerical calculation of a virtual ship is carried out and its results are investigated in terms of applicability to real ship design project.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1992년도 하계학술대회 논문집 B
• /
• pp.567-569
• /
• 1992

Design sensitivity analysis is proposed for the optimal shape design of three dimensional magnetostatic problems. The direct differentiation method is introduced for design sensitivity analysis and the boundary element method with reduced magnetic scalar potential as the state variable is used to analyze the magnetic characteristics. In the direct differentiation method, the design sensitivity, defined as the total derivative of the objective function with respect to the design variables, is calculated based on the variation of the state variable with respect to the design variable. And the variation of He state variable is calculated by differentiating the both sides of the system matrix equation obtained by applying boundary element method. Through the numerical example with simple electromagnet, the usefullness is proved.

• 대한전기학회논문지
• /
• 제41권8호
• /
• pp.850-857
• /
• 1992

Design sensitivity analysis is proposed for the optimal shape design of three-dimensional magnetostatic problems. The direct differentiation method is introduced for design sensitivity analysis and the boundary element method with reduced magnetic scalar potential as the state variable is used to analyze the magnetic characteristics. In the direct differentiation method, the design sensitivity, defined as the total derivative of the objective function with respect to the design variables, is calculated based on the variation of the state variable with respect to the design variable. And the variation of the state variable is calculated by differetiating the both sides of the system matrix equation obtained by applying boundary element method. Through the numerical example with simple electromagnet, the usefulness is proved.