• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.4
• /
• pp.2469-2475
• /
• 2014

In 1990s, with the increase of domestic building renovation but also increase the amount of anchor. The 45-degree cone failure theory has been used in concrete anchor bolts design, but the CCD (concrete capacity design) method was adopted as a new design method since 2000. However, the method has some problems because it is based on the experimental results of pre-installed concrete anchor bolts. In this study, the objective is to investigate the effects of anchor edge distance, anchor interval and concrete strength on pullout characteristics of post-installed concrete set anchor embedded in plain concrete.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.34 no.2
• /
• pp.367-375
• /
• 2014

Recently the use of concrete post-installed set anchors has been increasing because this constructing method is flexible and easy to attach or fix structural members when we repair, reinforce, or remodel a concrete structures. Depending on the shear strength of steel, the strength of concrete, edge distance and anchor interval, etc, the anchor loaded in shearing exhibits various failure modes such as steel failure, concrete failure, concrete pryout. In this study, the objective is to investigate the effects of the variations like anchor embedment depth, anchor interval, edge distance and concrete strength on the shear failure behavior of post-installed concrete set anchor embedded in concrete. The results of embedment depth experiments show that concrete strength has much effection on the shallow embedment depth. Steel failure occur to all results of the anchor interval experiments, but concrete is failed when edge distance experiments that less than the embedment depth. Through the comparision of the same parameters experiments results show that as strong as concrete strength are the displacement results are small.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.18 no.1
• /
• pp.40-47
• /
• 2014

Recently the use of concrete post-installed set anchors has been increasing because this constructing method is flexible and easy to attach or fix structural members when we repair, reinforce, or remodel structures. Accordingly, designers and builders of Korea depend on foreign design codes since there are no exact domestic anchor design codes that they could credit. The anchor in plain concrete loaded in tensile exhibits various failure modes such as concrete breakout, splitting, steel failure, pull-out and side-face blowout, that depending on the tensile strength of the steel, the strength of concrete, embedment depth, interval, the edge distance and the presence of adjacent anchor. The objective is to investigate the effects of the variations like anchor embedment depth, interval and edge distance on pull-out fracture behavior of post-installed concrete set anchor embedded in plain concrete.

• Journal of the Korean Geotechnical Society
• /
• v.33 no.11
• /
• pp.35-43
• /
• 2017

In this study, the pull-out resistance behavior of the anchor with the bump type resistors at the anchor body was experimentally investigated. In the model tests, the pull-out resistance was measured by pulling out the anchor at a constant speed. Anchor body was installed in the center of the circular sand tank. Pull-out tests were conducted for 10 conditions. The anchor type (existence of the resistor), the friction conditions of the anchor body surface ($1/3{\phi}$, $2/3{\phi}$, ${\phi}$), the bump type resistor set number (1set, 2set, 4set), and the height of resistors (0.05d, 0.10d, 0.20d) were varied. The load-displacement relationship for each conditions was measured during the pull-out tests at a constant speed (1 mm/min). Maximum pull-out length was 80 mm. As a result, the pull-out behavior of the friction type anchor and the expansion type anchor was different. As the number of resistor increased, the maximum pull-out resistance increased and the residual pull-out resistance ratio increased significantly, which were at 171~591 percent larger than that of the friction type anchor.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.17 no.5
• /
• pp.31-39
• /
• 2013

In this study, performance of the post-installed anchor system was evaluated with reduced strength of concrete and anchor. One of the post-installed anchors was selected to performance evaluation. Concrete strength was reduced by freeze-thawing test, and the post-installed anchor strength was reduced by corrosion test. The post-installed Anchor was installed in concrete of freezing and thawing and original concrete, and corroded anchor was installed in original concrete only. Anchor diameter and installation depth of the anchor were the variable for each specimen. Performance of post-installed anchor system of each specimen was evaluated by pullout test. Anchor diameter and installation depth of anchor, it may affect the performance of the post-installed anchor system from the experimental test results. Fracture mode of each post-installed anchor system had occurred differently depending on the durability of concrete and anchor. The anchor pullout strength from the experimental test results was used in order to compare with the results of CCD (Concrete Capacity Design) method, and CCD equation was modified. Modified equation was able to predict the anchor pullout strength of post-installed anchor system in Original concrete and freezing and thawing of concrete.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.19 no.3
• /
• pp.55-63
• /
• 2015

Post-installed concrete set anchors are installed after the concrete hardened. These anchors increasing usage in development of construction equipment and flexible construction. The anchor loaded in shearing exhibits various failure modes such as steel failure, concrete failure, concrete pryout, depending on the shear strength of steel, the strength of concrete, edge distance and anchor interval, etc,. In this study, the objective is to investigate the effects of the variations like anchor embedment depth, edge distance and concrete strength on experimental and finite element analysis of shear failure behavior of post-installed concrete set anchor for light load embedded in concrete. The results of embedment depth experiments show that concrete strength has much affection on the shallow embedment depth. Concrete strength has no much affection with anchor interval and edge distance parameter and both experimental results occurred same failure mode. By comparing the experimental results that occurred steel failure mode show that as strong as concrete strength are the displacement results are small.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.36 no.6
• /
• pp.743-748
• /
• 2003

An oil boom was set up in order to contain diffused oil from spills and for the retrenchment of damage caused by oil Pollution. Therefore, the oil boom anchor needed proper holding power to endure high resistance from flowing streams and to secure the oil boom around the spill, and must dredge directly into the seabed when it is dropped and block oil outflow immediately. This study investigated the holding power of the danforth anchor and the coastal fishing vessel anchor used for oil booms in the KMPRC (Korea Marine Pollution Response Corporation). For each type, a 30 kg and 20 kg anchor were used. The holding power of the danforth anchors were measured by dropping both weights 10 times. However the coastal fishing vessel anchors were dropped only 5 times each, because no substantial differences were found between drops. In the results of the danforth anchors, an anchor awoke occurred in 2 drops of the 30 kg anchor and in 4 drops of the 20 kg anchor, wherein there was no holding power to be measured. With exception to the anchor awoke cases, the maximum holding power of the danforth 30 kg and 20 kg anchors was 250-520 kg and 123-233 kg, respectively. In the case of the coastal fishing vessel anchors of 30 kg and 20 kg, throughout the experiment, there was no occurrence of an anchor awoke. For the 30 kg and 20 kg anchors, the maximum holding power was measured to be 209-230 kg and 155-170 kg, respectively. Therefore, the holding power of the coastal fishing vessel anchor was shown to be much poorer than that of the danforth anchor. However, the holding power of the danforth anchor was very unstable. Due to the occurrences of anchor awoke, there was no holding power and the measurement value of maximum holding power showed too much variation among the drop tests. Also, after the maximum holding power was achieved, anchor awoke occurred easily. In the case of the coastal fishing vessel anchor was much more stabile, because there was no anchor awoke and no instance where holding power failed. Also the maximum holding power was reached quickly and almost no variation occurred among the drop tests.

• Journal of Korean Society of Steel Construction
• /
• v.17 no.3 s.76
• /
• pp.271-283
• /
• 2005

This paper concerns the prediction of shear capacity, as governed by steel failure and concrete breakout failure, of set anchors installed in plain concrete. For this purpose, the methods to evaluate the shear capacity of the set anchors in concrete are summarized and the experimental data are compared with capacities by the two present methods : the method of ACI349-90 and the Concrete Capacity Design (CCD) method. (1) The constant-0.684 in the steel strength equation of set anchor was determined from shear test data at the 5 percent fractile probability. Consequently, it was concluded that the constant-0.6 and 0.5 in the steel strength equation for steel failure of ACI318-02 and EOTA were safe. The nominal shear strength of set anchor was proposed as following. $V_s=0.684 A_{se}f_{ut}$. (2) The CCD method was considered reasonable in estimating the concrete breakout strength of set anchors. In terms of the CCD method, the nominal concrete breakout strength of set anchor in shear was provided as follows; $V_b=0.609(\frac{\iota}{d_o})^{0.2}\sqrt{d_0}\sqrt{f_c}(c_1)^{1.5}$(N). (3) The CCD method was considered reasonable in estimating the concrete breakout strength for spacing of set anchors. The proposed equation was considered safe in estimating the concrete breakout strength for spacing of set anchors.

• Journal of the Korean Geotechnical Society
• /
• v.30 no.1
• /
• pp.5-16
• /
• 2014

This paper presents the results of an investigation into the pullout characteristics of screw anchor pile using field pullout tests. A series of field pullout tests were performed on screw anchor piles with different geometric characteristics such as shaft and screw diameters. The results indicated that screw anchor piles exhibited significantly higher pullout capacities compared with the same diameter piles without screw. Also observed is that the set-up effect and the grouting significantly increase pullout capacities, although the magnitude of the increase depends on the ground condition. In addition the applicability of prediction methods for helical pile pullout capacity to screw anchor piles was also examined. The results are presented in such a way that the pullout characteristics of screw anchor piles with different installation conditions can be identified. Practical implications of the findings are discussed.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.58 no.1
• /
• pp.10-18
• /
• 2022

Fishery sea anchor is widely used for many fishing vessels. However, standardization of the dimension and terminology of the fishery sea anchor has not been achieved, reducing the reliability of the performance and safety of the fishery sea anchor. Therefore, this study researches the reality of usage of fishery sea anchor and then attempts to suggest the development direction of the standard draft as basic data. As a result of the survey on the reality of usage show that various terms were used for each part of the fishery sea anchor (including the incorrect form of non-standard words derived from Japanese) and that the production of this product in the fishery sea anchor market was concentrated on one specific manufacturer. In addition, the main specifications of the fishery sea anchor are set and manufactured based on conventional experience without standards. In the field, there was no standardized drawing for fishery sea anchor and users had low awareness of the main specifications of fishery sea anchor. Therefore, this study suggested the following regarding the fishery sea anchor: standard terms for each part including Korean and English names and standard drawing of sea anchor. It is hoped that this study will contribute to research for the standardization of fishery sea anchor, which will increase in reliability and lead to increased interest in standardization in the fishery field.