• Bulletin of the Korean Chemical Society
• /
• v.24 no.12
• /
• pp.1814-1818
• /
• 2003

$Li^+$ and $H^+$ co-exchanged LSXs (Li-H-LSX) with various ratios of $Li^+$ and $H^+$ were prepared, and those adsorption characteristics of nitrogen and oxygen were compared with Li-Na-LSX and Li-Ca-LSX. Li-H-LSX showed higher nitrogen capacity and selectivity than that of Li-Na-LSX in the wide range of Li-exchanged ratio. The nitrogen capacity of Li-Ca-LSX was slightly higher than that of fully Li- or Ca-exchanged LSX (Li- LSX or Ca-LSX). However, Li-Ca-LSX showed low nitrogen/oxygen adsorption selectivity until the Li content reached about 80%, which was a tendency near that of Ca-LSX.

• Journal of Korean Society of Water and Wastewater
• /
• v.38 no.2
• /
• pp.95-107
• /
• 2024

This study proposes the use of a cobalt-based Prussian blue analogue (Co-PBA; potassium cobalt hexacyanoferrate), as an adsorbent for the cost-effective recovery of aqueous ammonium ions. The characterization of Co-PBA involved various techniques, including Fourier-transform infrared spectroscopy, X-ray diffraction, scanning electron microscopy, nitrogen adsorption-desorption analysis, and zeta potential. The prepared Co-PBA reached an adsorption equilibrium for ammonium ions within approximately 480 min, which involved both surface adsorption and subsequent diffusion into the interior. The isotherm experiment revealed a maximum adsorption capacity of 37.29 mg/g, with the Langmuir model indicating a predominance of chemical monolayer adsorption. Furthermore, the material consistently demonstrated adsorption efficiency across a range of pH conditions. Notably, adsorption was observed even when competing cations were present. Co-PBA emerges as a readily synthesized adsorbent, underscoring its efficacy in ammonium removal and selectivity toward ammonium.

• Composites Research
• /
• v.31 no.5
• /
• pp.267-275
• /
• 2018

A facile method for the preparation of nitrogen-doped microporous carbon via the pyrolysis of poly(vinylidene fluoride) (PVDF) using polypyrrole (PPy) as a selective nitrogen source was developed. A PVDF/PPy-800 sample (carbonized at $800^{\circ}C$) with a 1:0.5 ratio of PVDF and PPy exhibited the highest micropore volume. The activated microporous carbon materials obtained from PVDF/PPy-800 prepared at $800^{\circ}C$ with KOH possessed a large specific surface area and narrow pore-size distribution. They were characterized using $N_2$ adsorption at 77 K and argon (Ar) adsorption at 87 K, which allowed for the characterization of the narrow microporosity of the prepared materials due to the absence of interactions between Ar and the sample surface. In addition, the activated microporous carbon material with a KOH/carbon ratio of 2:1 was found to exhibit the largest specific surface area ($1296m^2g^{-1}$ in $N_2$ at 77 K) and microporosity, and a high specific capacitance ($122.8F\;g^{-1}$).

• Applied Chemistry for Engineering
• /
• v.16 no.1
• /
• pp.123-130
• /
• 2005

Zeolite X adsorbents with large surface area were prepared for using oxygen PSA adsorbent. Selective adsorption performance of nitrogen on the synthesized zeolite X adsorbent was improved by the cation exchange of adsorbent. The zeolite X which had over $650m^2/g$ surface area was synthesized at the conditions of $SiO_2\;:\;Na_2O\;:\;H_2O\;:\;Al_2O_3$ = 2.5 : 3.5 : 150 : 1 mole ratio, $98^{\circ}C$ temperature and 18 h synthesized time in 50 L reactor. The metal ions Li, Ag, Ca, Br, Sr, etc. were investigated for ion exchange with zeolite X. Ag ion was showed the highest ion exchange rate among these metal ions and all metal ions were exchanged with Na ion at equivalent rate. Compared with the NaX adsorbent, the ion exchanged zeolite X adsorbent remarkably improved its adsorption performance of nitrogen at the conditions of $10{\sim}40^{\circ}C$ temperature and 0~9 atm pressure. At an equilibrium pressure under 0.5 atm, adsorption performance of nitrogen on the ion exchanged zeolite adsorbent increased in the order of Ag > Li > Ca > Sr> Ba > K, whereas at an equilibrium pressure over 1 atm showed in the order of Li > Ag > Ca > Sr > Ba > K. Nitrogen/oxygen separation factor of Li ion exchanged zeolite X adsorbent was 13.023 at the partial pressure of nitrogen/oxygen gas mixture similar to air and $20^{\circ}C$ adsorption temperature.

• Journal of Korean Society for Atmospheric Environment
• /
• v.33 no.1
• /
• pp.1-10
• /
• 2017

Adsorption is a plausible technology using solid adsorbents for dry capture of carbon dioxide ($CO_2$). In general, narrow size distribution of tiny pores and surface chemical functionalities of solid adsorbents enhance the adsorption capacity of gaseous $CO_2$ molecules. In order to utilize the advantages of fibrous adsorbents, this work prepared activated carbon nanofibers (ACNFs) via the electrospinning process using a polymer precursor of polyacylonitrile (PAN). The spun fibers were 390 nm to 580 nm in thickness with an average surface area of $27.3m^2/g$. The surface structure was improved by a programmed thermal activation at $800^{\circ}C$ in $CO_2$ atmosphere. It was also found that the nitrogen-groups including pyrrole and pyridine were created during the activation facilitaing the selective adsorption as forming enhanced active sites. The finally obtained adsorption capacities were 2.74 mmol/g for pure $CO_2$ flow and 0.74mmol/g for 3000 ppm.

• Clean Technology
• /
• v.23 no.1
• /
• pp.1-14
• /
• 2017

At high nitrate concentrations, water must be treated to meet regulated concentrations because it results in threat to human health and eutrophication of natural water. However, it is almost impossible to remove nitrate by conventional water treatment methods such as coagulation, filtration and precipitation, due to its high water solubility. Therefore, other technologies including adsorption, ion exchange, reverse osmosis, denitrification, and electrodialysis are required to effectively remove nitrate. Each of these technologies has their own strengths and drawbacks and their feasibility is weighted against factors such as cost, water quality improvement, residuals handling, and pre-treatment requirements. An adsorption technique is the most popular and common process because of its cost effectiveness, ease of operation, and simplicity of design. Surface modifications of adsorbents have been enhanced their adsorption of nitrate. The nitrate-selective membrane process of electrodialysis reversal and reverse osmosis have proven over time and at many locations to be highly effective in removing nitrate contaminating problems in aqueous solutions. Both electrodiaysis and reverse osmosis methods generate highly concentrated wastes and need careful consideration with respect to disposal.

• Korean Chemical Engineering Research
• /
• v.47 no.5
• /
• pp.608-614
• /
• 2009

In this work, ruthenium substituted SBA-15's(Ru-SBA15's) of various Si/Ru ratios were prepared using a non-ionic triblock copolymer surfactant, $EO_{20}PO_{70}EO_{20}$, as template. We investigated the nitrogen or oxygen adsorption/desorption behaviors of the Ru-SBA-15's for their future applications as catalysts or selective adsorbents, etc. The pore size of the Ru-SBA-15's was determined by both the Barrett-Joyner-Halenda(BJH)($D_{BJH}$) and the Broekhoff-de Boer analysis with a Frenkel-Halsey-Hill isotherm(BdB-FFF) method($D_{BdB-FHH}$). The $D_{BJH}$ and $D_{BdB-FHH}$ of the Ru-SBA-15 having 50/1 ratio of Si/Ru were 3.9 nm and 4.7 nm, respectively. The transmission electron microscope(TEM) image of the Ru-SBA 15 of the Si/Ru mole ratio of 50 showed that the pore size is 4.7 nm, which is consistent with the $N_2$ adsorption results with the BdB-FHH method. The surface area of pores form oxygen adsorption/desorption isotherm was higher than that from the nitrogen adsorption/desorption isotherm by the Brunauer-Emmett-Teller(BET) method, which were respectively $612.7m^2/g$, and $573.3m^2/g$. X-ray diffraction(XRD) patterns and TEM analyses showed that the mesoporous materials possess well-ordered hexagonal arrays.

• Journal of the Korean Ceramic Society
• /
• v.55 no.3
• /
• pp.261-266
• /
• 2018

Hollow or bumpy ZnO structures with micrometer-size features have been investigated as photocatalysts for water purification due to their high surface area available for reaction with harmful organic molecules and relatively large size for easy separation after finishing the photocatalytic reaction. In this study, selective synthesis of ZnO hollow or crumpled microspheres was performed using a simple and versatile ultrasonic spray pyrolysis process with various zinc precursors. The morphologies, phases, specific surface areas, and optical properties of the microspheres were characterized using X-ray diffraction, scanning electronic microscopy, nitrogen adsorption-desorption isotherms, and UV-vis spectroscopy. In addition, the mechanism underlying the formation of different morphologies and their photocatalytic activities were systematically investigated.

• Journal of the Korean Chemical Society
• /
• v.61 no.5
• /
• pp.231-237
• /
• 2017

Efficiently removing Al(III) from rare earth is very significant because even trace amount of Al(III) can cause serious harm to the rare earth materials. In this paper, a nitrogen-containing activated carbon, AC-P700, was synthesized using peas as raw materials. The AC-P700 was characterized by surface area analyzer, FT-IR, and XPS methods. The adsorption and recognition properties of AC-P700 towards Al(III) were investigated, and the recognition mechanism was also analyzed. The BET special surface area of AC-P700 was $1277.1m^2{\cdot}g^{-1}$, and the average pore diameter was 1.90 nm. The AC-P700 possesses strong adsorption affinity and excellent recognition selectivity towards Al(III). The adsorption capacity for Al(III) could reach to $0.53mmol{\cdot}g^{-1}$, and relative selectivity coefficients relative to La(III) and Ce(III) is 9.6 and 8.7, respectively. Besides, AC-P700 possesses better regeneration ability and reusability.

• Korean Journal of Materials Research
• /
• v.33 no.5
• /
• pp.195-204
• /
• 2023

Micro-electronic gas sensor devices were developed for the detection of carbon monoxide (CO), nitrogen oxides (NO_x), ammonia (NH₃), and formaldehyde (HCHO), as well as binary mixed-gas systems. Four gas sensing materials for different target gases, Pd-SnO₂ for CO, In₂O₃ for NO_x, Ru-WO₃ for NH₃, and SnO₂-ZnO for HCHO, were synthesized using a sol-gel method, and sensor devices were then fabricated using a micro sensor platform. The gas sensing behavior and sensor response to the gas mixture were examined for six mixed gas systems using the experimental data in MEMS gas sensor arrays in sole gases and their mixtures. The gas sensing behavior with the mixed gas system suggests that specific adsorption and selective activation of the adsorption sites might occur in gas mixtures, and allow selectivity for the adsorption of a particular gas. The careful pattern recognition of sensing data obtained by the sensor array made it possible to distinguish a gas species from a gas mixture and to measure its concentration.