• 한국방재학회 논문집
• /
• 제8권3호
• /
• pp.67-75
• /
• 2008

본 논문은 형강을 이용한 강-콘크리트 합성복공판 기술개발에 관한 것이다. 기존의 롤포밍 단면을 배제하고 형강을 이용하여 효율적인 강합성 단면을 구성함으로써 제작성과 경제성을 확보하고, 전단연결재의 개선을 통해 합성성능 뿐만 아니라 차후 콘크리트와 강재의 분리에 용이한 구조를 개발하였다. 성능검증 실험결과 기존의 전단연결재만으로는 강재와 콘크리트의 합성거동을 이루는데 한계가 있음을 확인하였다. 나아가 개발 복공판은 설계하중대비 5배 이상의 극한 내하력을 확보하고 있으며, 200만회 피로성능시험에 대해서도 손상이 거의 발생하지 않으며 우수한 구조성능을 나타냈다. 따라서, 형강을 이용한 합성단면 구성을 통해 구조성능 확보뿐만 아니라 기존 합성복공판 대비 약 27% 정도의 강재량 감소가 가능함을 확인하였다.

• 한국산학기술학회논문지
• /
• 제12권12호
• /
• pp.5910-5916
• /
• 2011

강재는 단면의 종류와 크기 및 부재에 따라 화재에 노출되는 표면적이 달라지며, 이에 따라 화재에 의한 강재의 온도상승도 큰 차이를 나타낸다. 단면형상계수($H_p$/A)는 강재의 종류, 크기, 적용부재 및 내화피복재의 종류 등의 변수에 따라 결정되며, 이것은 내화피복 두께를 결정하는 기준이 된다. 본 연구를 통하여 강재는 종류에 관계없이 단면의 크기가 증가할수록 단면형상계수는 감소하는 것을 알 수 있었다. 단면형상계수에 따른 강재의 종류별 내화피복 두께 산정 결과 1시간 내화성능은 기준보다 소요 두께가 30~50% 낮게 나타났다. 또한, 2시간 내화성능은 기준보다 소요 두께가 최저 27% 낮게 산정되는 부재도 있으나 대체로 기준에 근접하는 것을 알 수 있었다. 그러나 H형강의 경우 3시간 내화성능은 대체로 기준을 만족하지만 각형강관과 원형강관의 경우 5.0~17.5% 정도 기준을 상회하는 값으로 나타났다.

• Steel and Composite Structures
• /
• 제47권3호
• /
• pp.423-436
• /
• 2023

In this research, we tested 10 simply supported concrete-encased composite columns under monotonic eccentric loads and investigated their shear behaviour. The specimens tested were two reinforced concrete specimens, three steel-reinforced concrete (SRC) specimens with an H-shaped steel section (also called a beam section), and five SRC specimens with a cruciform-shaped steel section (also called a column section). The experimental variables included the transverse steel shape's depth and the longitudinal steel flange's width. Experimental observations indicated the following. (1) The ultimate load-carrying capacity was controlled by web compression failure, defined as a situation where the concrete within the diagonal strut's upper end was crushed. (2) The composite effect was strong before the crushing of the concrete outside the steel shape. (3) We adjusted the softened strut-and-tie SRC (SST-SRC) model to yield more accurate strength predictions than those obtained using the strength superposition method. (4) The MSST-SRC model can more reasonably predict shear strength at an initial concrete softening load point. The rationality of the MSST-SRC model was inferred by experimentally observing shear behaviour, including concrete crushing and the point of sharp variation in the shear strain.

• Steel and Composite Structures
• /
• 제44권5호
• /
• pp.677-684
• /
• 2022

This paper reports experimental investigation on shear behavior of steel reinforced concrete (SRC) shallow floor beam, where the steel shape is embedded in concrete and the high strength bolts are used to transfer the shear force along the interface between the steel shape and concrete. Six specimens were conducted aiming to provide information on shear performance and explore the shear bearing capacity of SRC shallow floor beams. The effects of the height of concrete slab, the size and the type of the steel section on shear performance of beams were also analyzed in the test. Based on the strut-and-tie model, the shear strength of the SRC shallow floor beam was proposed. Experimental results showed that composite shallow floor beam exhibited satisfactory composite behavior and all of the specimen failed in shear failure. The shear bearing capacity increased with the increasing of height of concrete slab and the size of steel shape, and the bearing capacities of beam specimens with castellated steel shape was slightly lower than those of specimens with H-shaped steel section. Furthermore, the calculations for evaluating the shear bearing capacity of SRC shallow floor beam were verified to be reasonable.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2021년도 봄 학술논문 발표대회
• /
• pp.185-186
• /
• 2021

In Korea, many buildings are built with underground spaces and cast-in-place pile method is mostly applied in the temporary retaining walls for the underground space construction. A H-shaped steel section is generally embedded in the soldier pile in the C.I.P method. In this study, a new and economical section with high strength steel replacing the H-shaped section was proposed and its flexural capacity was evaluated experimentally. The new section is the concrete-filled composite section with pentagonal thin plate and thick flange plate. Test results showed that the proposed section has an excellent flexural strength and ductility.

• 교육녹색환경연구
• /
• 제9권1호
• /
• pp.32-40
• /
• 2010

The purpose of this study was to evaluate structural safety and economic efficiency of prestressed hybrid beam using T-shape steel member which was developed to build large span educational facilities. Hybrid beam specimens were manufactured with 16.0m long and load was uniformly distributed by 12.0kN steel hexahedrons. In this study, honeycomb beam design process was introduced to T-shape section steel beam design. Vibration condition of specimens were analyzed by Korea Building Code 2009 and AISC Steel Design Guide Series-11. As a result, the prestressed hybrid beam with T-shape steel member has about 10.4% of cost reduction effect.

• 산업기술연구
• /
• 제1권
• /
• pp.9-16
• /
• 1981

In the steel Structural design, buckling is the main factor to determine size, particularly in compression member. Buckling may sometimes occur in the form of wrinkles in thin elements, such as webs, flanges, and other parts that make up a section. This phenomenon is called local buckling. The strength of the steel and the rigidity of the frame are considerably deteriorated by the local buckling. The specimens used for this experiments, H-Shape Steel beams composed by fillet-welding, are dessified classified into two groups, ie one for web test and another for flange fest. The aim of this study is to define the influences by the local bucking on the vesisting forces, deformation and the phenomena of the internal forces in the section, and to collect the basic data for design of steel beams.

• 한국지진공학회:학술대회논문집
• /
• 한국지진공학회 2005년도 학술발표회 논문집
• /
• pp.300-307
• /
• 2005

Steel Reinforced Concrete (SRC) composite column has several advantage such as excellent durability, rapid construction, reduction of column section. Due to these aspect, applications of SRC columns to bridge piers are continuously increasing. For the design of relatively large SRC columns for bridge piers, it is necessary to check the current design provisions which were based on small section having higher steel ratio. In this study, seven concrete encased composite columns were fabricated and static tests were performed. Embedded steel members were a H-shape rolled beam and a partially filled steel tube. Based on the test results, the ultimate strength according to section details and local behavior were estimated. For the analysis of inelastic behavior of the SRC column, the cracked section stiffness of the columns was evaluated and compared with calculations. The stiffness of the cracked section showed that 25% of the initial value and this stiffness reduction occurred at 85% of the ultimate load in the experiments.

• 복합신소재구조학회 논문집
• /
• 제2권3호
• /
• pp.30-35
• /
• 2011

본 연구에서는 신형상 층고절감형 합성보에 대한 최적단면을 도출하기 위해 단면성능 계산 프로그램을 개발하여 단면성능에 대해 비교 분석을 하였다. 신형상 합성보는 상부 플랜지 하부에 바닥시스템이 위치하여 전통적인 공법에 비해 층고절감의 효과와 최적단면으로 설계시 공기의 단축과 비용의 절감은 물론 물량의 감소를 기대 할 수 있다. 그러나 단면은 기존 H형강 보와 달리 상하 비대칭으로 중립축의 위치가 중앙에 위치하지 않기 때문에 상하연단에 대한 단면계수가 같지 않게 된다. 이에 따른 상하플랜지 판요소의 두께비에 따른 매개 변수적 분석이 요구된다. 따라서, 본 연구에서는 단면의 상부 플랜지 두께에 대한 하부 플랜지 두께의 비에 따른 중립축위치, 단면계수의 변화추이를 분석하여 최적단면을 도출하는데 주목적을 두었다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제4권3호
• /
• pp.153-160
• /
• 2000

In simply supported composite beams, the neutral axis of the composite cross section usually is located the top flange of the steel I-shape, so that the top flange does not impart much strength to the member. This suggests that omitting the top flange entirely could be a means to lower the cost of the beam without greatly reducing the strength. The purpose of this investigation is to research flexural strength and behavior of the composite beams with reduced top flange of steel. Five specimens with H and inverted T steel section were tested. As the test results, comparison of the experimental to computed full-plastic moment, and variations of flexural strength with reduced top flange were analyzed.