ZnO shows a direct band gap of 3.37eV, large exciton binding energy (~60 meV), high oxidation ability, high sensitivity to many gases, and low cost, and it has been used in various applications such as transparent electrodes, light emitting diodes (LEDs), gas sensors and photocatalysts. Among these applications ZnO as photocatalyst has considerably attracted attention over the past few years because of its high activities in removing organic contaminants generated from industrial activities. In this research, ZnO nanoparticles were synthesized by spray-pyrolysis method using the zinc acetate dihydrate as starting material at synthesis temperature of $900^{\circ}C$ with concentration varied from 0.01 to 1.0M. The physical and chemical properties of the synthesized ZnO nanoparticles were examined by X-ray Diffraction (XRD), Scanning Electron Microscopy (SEM), Fourier Transformation Infrared (FT-IR), and UV-vis spectroscopy. The Miller indices of XRD patterns indicate that the synthesized ZnO nanoparticles showed a hexagonal wurtzite structure. With increased precursor concentration, a primary, secondary particle sizes of ZnO nanoparticles increased by 0.8 to $1.5{\mu}m$ and 15 to 35nm, and their crystallinity was improved. Methyleneblue (MB) solution ($1{\mu}M$) as a test comtaminant was prepared for evaluating the photocatalytic activities of ZnO nanoparticles synthesized in different precursor concentration. The results show that the photocatalytic efficiency of ZnO nanoparticles was gradually enhanced by increased precursor concentration.
The very high temperature gas reactor (VHTR) is one of the next generation nuclear reactors for its safety, long-term stability, and proliferation-resistance. The high operating temperature of over 800$^{\circ}C$ enables various applications with high energy efficiency. Heat is transferred from the primary helium loop to the secondary helium loop through the intermediate heat exchanger (IHX). The IHX material requires creep resistance, oxidation resistance, and corrosion resistance in a helium environment at high operating temperatures. A Ni-based superalloy such as Alloy 617 is considered as a primary candidate material for the intermediate heat exchanger. In this study, the microstructures of Alloy 617 crept in pure helium and air environments at 950$^{\circ}C$ were observed. The rupture time in helium was shorter than that in air under small applied stresses. As the exposure time increased, the thickness of outer oxide layer of the specimens clearly increased but delaminated after a long creep time. The depth of the carbide-depleted zone was rather high in the specimens under high applied stress. The reason was elucidated by the comparison between the ruptured region and grip region of the samples. It is considered that decarburization caused by minor gas impurities in a helium environment caused the reduction in creep rupture time.
Magnetite was chosen as a typical adsorbent to study its phosphate adsorption capacity in water body with low concentration of phosphorus (below $2mg\;PL^{-1}$). Magnetite was collected from Luoyang City, Henan Province, China. In this research, three factors have been studied to describe the adsorption of phosphate on magnetite, which was solution concentration (concentration ranging from 0.1 to $2.5mg\;PL^{-1}$), suspension pH (1 to 13) and temperature (ranging from $10^{\circ}C$ to $40^{\circ}C$). In addition, the modified samples had been characterized with XRD and FE-SEM image. The results show that iron ions contains in magnetite were the main factors of phosphorus removal. The behavior of phosphorus adsorption to substrates could be fitted to both Langmuir and Freundlich isothermal adsorption equations in the low concentration phosphorus water. The theoretical saturated adsorption quantity of magnetite is 0.158 mg/g. pH has great influence on the phosphorus removal of magnetite ore by adsorption. And pH of 3 can receive the best results. While temperature has little effect on it. Magnetite was greatly effective for phosphorus removal in the column experiments, which is a more practical reflection of phosphorous removal combing the adsorption isotherm model and the breakthrough curves. According to the analysis of heavy metals release, the release of heavy metals was very low, they didn't produce the secondary pollution. The mechanism of uptake phosphate is in virtue of chemisorption between phosphate and ferric ion released by magnetite oxidation. The combined investigation of the magnetite showed that it was better substrate for water body with low concentration of phosphorus.
폴리에틸렌은 농업용 필름으로 널리 사용되고 있지만, 이를 친환경적으로 분해하기 위한 기술은 부족한 상황이다. 이에 최근 폴리에틸렌 분해를 위한 친환경 기술 개발에 대한 관심이 높아지고 있다. 폴레에틸렌의 생물학적 분해에는 몇가지 산화 단계가 필요할 것이라고 예상된다. 먼저, 폴리에틸렌 사슬에 2차 알코올이 형성되고, 알코올은 카르보닐기로 산화된다. 이후 과정에서 카르보닐기는 Baeyer-Villiger monooxygenase (BVMO)에 의해 에스터로 전환되고, 이 에스터는 마지막 단계에서 lipase와 esterase에 의해 절단될 것으로 예상된다. 본 연구에서는 폴리에틸렌 분해 과정에 관여하는 중요한 효소 중 하나인 BVMO의 반응 메커니즘, 분류, 효소공학 측면에서 리뷰하였다. 또한 BVMO를 사용한 폴리에틸렌 분해 분야의 향후 연구전망도 간략히 덧붙였다.
In the present study, we investigated the sulfur poisoning of the Ni anode in solid oxide fuel cells (SOFCs) as a function of operating conditions. Anode supported cells were fabricated, and sulfur poising tests were conducted as a function of current density, $H_2S$ concentration and humidity in the anode gas. The voltage drop was significant under the higher current density (${\sim}714mA/cm^2$) condition, while it was much reduced under the lower current density (${\sim}389mA/cm^2$) condition, at 100 ppm of $H_2S$. A secondary voltage drop, which occurred only at the high current density, was attributed to Ni oxidation in the anode. Thus, operation at high current density with high $H_2S$ concentration may lead to permanent deterioration in the anode. The effect of water content (10%) on the sulfur poisoning was also investigated through a constant current test (${\sim}500mA/cm^2$) at 10 ppm of $H_2S$. The cell operating with 10% wet anode gas showed a much smaller initial voltage drop, in comparison with a dry anode gas. The present study indicates that operating conditions, such as gas humidity and current density, should be carefully taken into account, especially when fuel cells are operated with $H_2S$ containing fuel.
Barbara Elizabeth van Wyngaard;Arno Hugo;Phillip Evert Strydom;Foch-Henri de Witt;Carolina Henritta Pohl;Arnold Tapera Kanengoni
Animal Bioscience
/
제36권9호
/
pp.1414-1425
/
2023
Objective: Long chain n-3 polyunsaturated fatty acids (PUFA) exert positive effects on human health. The long chain n-3 PUFA of pork can be increased by adding fish oil to the diet. Due to the cost and availability of fish oil an alternative source must be found. Methods: This study evaluated the effect of five dietary oils on meat quality, fatty acid composition and lipid stability. The five diets contained 1% palm oil (Control), 1% soya oil, 1% linseed oil, 1% fish oil, and 1% Echium oil, respectively. The trial consisted of 60 gilts, randomly allocated to five groups. Results: All color parameters, extractable fat content, fat free dry matter, and moisture content of the m. longissimus muscle were unaffected by dietary treatment. Consumers and a trained sensory panel could not detect a difference between the control samples and the Echium oil sample during sensory analysis. Samples containing higher levels of PUFA (soya, linseed, fish, and Echium oil) had higher levels of primary and secondary lipid oxidation products after refrigerated and frozen storage. However, these values were still well below the threshold value where off flavors can be detected. The Echium oil treatment had significantly higher levels of long chain PUFA than the linseed oil treatment, but it was still significantly lower than that of the fish oil treatment. Conclusion: Echium oil supplementation did not increase the levels of n-3 to the same extent as fish oil did. The result did however suggest that Echium oil can be used in pig diets to improve muscle long chain n-3 fatty acid content without any adverse effects on meat quality when compared to linseed, soya, and palm oil.
금은광산의 광미에는 유비철석이 포함되어 있으며 이의 산화로 주변 지구화학적 환경에서 비소오염 양상이 주로 나타나고 있다. 풍화된 광미의 경우 황화광물의 산화과정으로 철 수산화물 및 수산화황산염이 풍부하게 생성되고 여기에 비소가 결합되어 있을 것으로 예상된다. 이 연구에서는 국내 일부 금은광산 지역의 풍화된 광미를 대상으로 SEW/EDS 분석과 연속추출분석을 실시하여 고상 비소의 광물학적, 화학적 특성을 파악하였다. 또한 pH/Eh 환경변화에 따른 고상 비소의 안정도와 용출 가능성을 평가하였다. 광미시료들은 총 황 몰농도와 비소 및 중금속원소들의 함량을 비교해 볼 때 풍화로 인해 황화광물의 산화가 많이 진행된 것으로 나타났다. XRD 분석에서 덕음, 동일, 다덕 광산 광미에서 철수산화황산염 광물로서 자로사이트가 나타났으며 비소의 총함량이 가장 높게 나타난(4.36%) 다덕광산 광미에서 결정질 비소 함유상으로 스코로다이트가 확인되었다. 이외 SEM/EDS 분석을 통해 보이단타이트와 유사한 조성을 가지는 상자 일부 Pb-비산염 형태도 구분되었으며 상대적으로 광미의 풍화정도가 낮은 삼광 및 구봉 지역에서는 유비철석이 인지되기도 하지만 광미내 비소는 주로 철수산화물 및 수산화황산염에 결합된 것으로 나타났다. 화학적 형태 분석에서도 동일, 다덕, 명봉 광산 광미에서 철수산화물과 공침전된 형태가 72∼99%로 나타났으며 삼광 및 구봉에서는 황화물 형태가 58%, 철수산화물 결합형태가 40% 내외로 나타나 이를 뒷받침한다. 광미에 대한 비소 용출실험에서 덕음 광미가 가장 낮은 pH(2.7)를 의이며 직접적인 철수산화황산염의 용해반응으로 비소가 용출되며 삼광 및 구봉에서는 알칼리성 환경(8.1-8.5)에서 탈착반응으로 상대적으로 많은 양의 비소가 용출될 수 있음을 보여주었다. 또한 산성환경에서 용존 비소의 +3가 비율이 높게 차지하여 환경적 영향이 크게 나타날 수 있다. 이와 같은 풍화 광미에 대해 환경복구 기법의 적용으로 인한 pH/Eh 환경의 변화와 미생물의 작용이 비소를 함유하는 상의 안정도에 영향을 줄 수 있으며 비소의 용출 정도는 증가할 수 있다.
중금속 이온이나 방사성 양이온을 처리하는 공정으로서 화학약품에 의한 침전법이나 일반 이온교환법을 가장 보편적으로 활용하고 있으나, 이 공정들은 약품의 과다 투여, 유효 금속의 폐기, 고형 폐기물에 의한 2차적인 토양 오염 유발 등과 같은 문제점을 가지고 있다. 이에 따라 최근 들어 선진국을 중심으로 전해환원 전착반응과 이온교환 반응을 결합시킨 전기화학적 이온교환법을 대체 신기술로 개발하고자 많은 관심과 연구가 집중되고 있다. 본 연구에서는 전기화학적 이온교환체 중의 하나인 nickel hexacyanoferrate (NiHCNFe)의 최적 제조조건을 규명하기 위해, 기지금속인 니켈판 표면에 화학적 방법과 전기화학적 방법으로 NiHCNFe 막을 생성하였으며, NiHCNFe의 구조 형태와 조성을 각각 SEM과 EDS 분석을 통하여 조사하였다. 또한 NiHCNFe 막이 생성된 니켈판을 운전전극으로 설치한 단일 평행평판 이온교환 전극반응기에서 산화-환원 전위를 연속적으로 순환시켜 순환전위곡선을 측정하고 피크 전류의 변화 거동을 조사하였다. 본 연구의 실험 결과에 의하면, 화학적으로 제조한 NiHCNFe가 전기화학적으로 제조한 경우보다 우수함을 알 수 있었고, 특히 118 h 화학반응시킨 NiHCNFe 이온교환체의 조밀도, 밀착성, 내구력이 가장 우수하게 나타났다.
$V_2O_5/TiO_2$계 촉매상에서 $NH_3$에 의한 $NO_x$의 선택적환원은 310의 지구온난화지수를 갖는 $N_2O$의 또 다른 인위적인 배출원이 될 수 있는 것으로 보고되고 있으므로, 본 총설은 화석연료를 연소시키는 화력발전소용 상기 촉매상에서 SCR 탈질반응 동안에 $N_2O$ 생성과 관계되는 주요 변수들의 유의성을 다루고자 한다. $NH_3$-SCR 탈질반응에서 $N_2O$ 배출은 $NH_3$ 산화반응에 더하여 반응 중에 존재하는 $NO_x$와 $NH_3$ 간의 부반응을 통해 일어나 이 부반응들의 정도는 SCR 촉매의 활성성분인 $V_2O_5$의 함량과 조촉매의 종류($WO_3$와 $MoO_3$), 반응온도, $NO_2/NO_x$ 비율, 산소농도, 공간속도, 수분함량, 열처리 등과 같은 유입가스 조건과 운전변수 및 화력발전소 현장에 설치된 상용 SCR 탈질공정에서 격은 촉매의 이력에 크게 의존한다. 상기의 모든 변수들이 탈질반응에서 $N_2O$ 생성과 관계된다고 할지라도, 몇몇 핵심변수들이 $N_2O$ 생성에 미치는 영향과 상용 SCR 공정에서 $N_2O$ 생성을 억제할 수 있는 방안이 고찰되었다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.