• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 추계학술대회 논문집
• /
• pp.389-392
• /
• 1997

This paper presents the dynamic analysis and experiment for rotor systems supported by angular contact ball bearings subjected to axial displacement preload. A dynamic software, which has been developed by the authors for the analysis of rotor systems supported by angular contact ball bearings, is used to simulate a uniform shaft system supported by two angular contact ball bearings with the axial displacement preload varied. Experiments are also performed to validate the simulation. An experimental system is constructed which consists of a uniform shaft, two bearings and a device for adjusting the axial displacement preload. Through a series of simulation and experiment, the dynamic characteristics of rotor systems with angular contact ball bearings subject to axial displacement preload are investigated.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• 제11B권2호
• /
• pp.9-14
• /
• 2001

Because salient pole rotor type single phase SRM(Switched Reluctance Motor) has a simple structure and can be use both radial and axial direction magnetic flux at the same time, its output power per unit volume is high. Therefore, the shaft length can be minimized when compared with same output motors. However, salient pole rotor is hard to design due to its complex magnetic circuit. In this paper, salient pole rotor type single phase SRM with minimized shaft length is designed and selected the most suitable dimension of rotor, stator, pole arc and salient pole.

• Journal of Mechanical Science and Technology
• /
• 제17권1호
• /
• pp.57-63
• /
• 2003

An eigenvalue design sensitivity formulation of a general nonsymmetric-matrix rotor-bearing system is devised. using the DDM (direct differential method). Then, investigations on the design sensitivities of critical speeds are carried out for an APU turbogenerator with a spline shaft connection. Results show that the dependence of the rate of change of the critical speed on the stiffness changes of bearing models of spline shaft connection points is negligible, and thereby their modeling uncertainty does not present any problem. And the passing critical speeds up to the 4th critical speed are not sensitive to the design stiffness coefficients of four main bearings. Further, the dependence of the rate of change of the critical speed on the shaft-element length changes shows quantitatively that the spline shaft has some limited influence on the 4th critical speed but no influence on the 1st to 3rd critical speeds. With no adverse effect from the spline shaft, the APU system achieves a critical speed separation margin of more than 40% at a rated speed of 60,000 rpm.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 춘계학술대회 논문집
• /
• pp.401-404
• /
• 2007

Inertia welding is a solid-state welding process in which butt welds in materials are made in bar and in ring form at the joint face, and energy required for welding is obtained from a rotating flywheel. The stored energy is converted to frictional heat at the interface under axial load. The quality of the welded joint depends on many parameters, including axial force, initial revolution speed and energy, amount of upset, working time, and residual stresses in the joint. Inertia welding was conducted to make the large rotor shaft for low speed marine diesel engine, alloy steel for shaft of 140mm. Due to different material characteristics, such as, thermal conductivity and flow stress, on the two sides of the weld interface, modeling is crucial in determining the optimal weld geometry and parameters. FE simulation was performed by the commercial code DEFORM-2D. A good agreement between the predicted and actual welded shape is observed. It is expected that modeling will significantly reduce the number of experimental trials needed to determine the weld parameters.

• 한국정밀공학회지
• /
• 제18권2호
• /
• pp.119-125
• /
• 2001

This paper presents an experimental study on active control of self-excited vibration for a high speed turbomachinery. In order to suppress the self-excited vibration, it is necessary to actively control the air film pressure or the air film thickness. In this study, active pads are used to control the air film thickness. Active pads are supported by pivots containing piezoelectric actuators and their radial position can be actively controlled by applying voltage to the actuators. The transfer characteristics from actuator inputs to shaft vibration outputs are experimentally investigated. In a tilting-pad gas bearing (TPGB), a shaft is supported by the pressurized air film. Four gap sensors were used to measure the vibration of the shaft and PID was used in the feedback control of the shaft vibration. The experimental results show that the self-excited vibration of the rotor can be effectively suppressed if the PID controller gains are properly chosen. As a result we find that the feedback control is effective for suppressing the self-excited vibration of a rotor system using stack-type PZT actuators.

• 소성∙가공
• /
• 제16권4호
• /
• pp.266-270
• /
• 2007

Inertia welding is a solid-state welding process in which butt welds in materials are made in bar and in ring form at the joint face, and energy required for welding is obtained from a rotating flywheel. The stored energy is converted to frictional heat at the interface under axial load. The quality of the welded joint depends on many parameters, including axial force, initial revolution speed and energy, amount of upset, working time, and residual stresses in the joint. Inertia welding was conducted to make the large rotor shaft for low speed marine diesel engine, alloy steel for shaft of 140mm. Due to material characteristics, such as, thermal conductivity and high temperature flow stress, on the two sides of the weld interface, modeling is crucial in determining the optimal weld parameters. FE simulation is performed by the commercial code DEFORM-2D. A good agreement between the predicted and actual welded shape is observed. It is expected that modeling will significantly reduce the number of experimental trials needed to determine the weld parameters.

• 한국소음진동공학회논문집
• /
• 제12권5호
• /
• pp.380-388
• /
• 2002

This paper describes the optimum design for low-pressure steam turbine rotor of 1,000 MW nuclear power plant by using a combined genetic algorithm, which uses both a genetic algorithm and a local concentrate search algorithm (e.g. simplex method). This algorithm is not only faster than the standard genetic algorithm but also supplies a more accurate solution. In addition, this algorithm can find the global and local optimum solutions. The objective is to minimize the resonance response (Q factor) and total weight of the shaft, and to separate the critical speeds as far from the operating speed as possible. These factors play very important roles in designing a rotor-bearing system under the dynamic behavior constraint. In the present work, the shaft diameter, the bearing length, and clearance are used as the design variables. The results show that the proposed algorithm can improve the Q factor and reduce the weight of the shaft and the 1st critical speed.

• 한국소음진동공학회논문집
• /
• 제22권7호
• /
• pp.659-666
• /
• 2012

A nonlinear dynamic model for the shaft-disk-blade unit is developed in this study. In this regard, the rotating flexible blade, with a pre-twist angle, attached to a rigid disk driven by a shaft which is flexible in torsion is developed. The rotor-blade coupled model is derived using Lagrange equation in conjunction with the assumed mode method to discretize the blade deformation. The equations of motion are analyzed based on the small deformation theory for the blade and shaft torsional deformation to obtain the system natural frequencies for various system parameters.

• Advances in aircraft and spacecraft science
• /
• 제5권1호
• /
• pp.51-71
• /
• 2018

This work proposes a theoretical and numerical study on the behavior of a tapered shaft rotor made of composite materials by the classical version h and the version p of the finite element method. Hierarchical form functions are used to define the model. The purpose of this paper is to determine the expressions of the kinetic and potential energies of the tree necessary for the results of the equations of motion. A comparison between the version h and the p version of the finite element method of the functions of polynomial and trigonometric hierarchical forms with six degrees of freedom per node, of a composite tapered and cylindrical shaft which rotates at a constant speed about its axis. It is found that when the number of functions of form (the version p) is increased, the solution converges. It is also observed that the conicity of the shaft increases the rigidity with respect to a uniform shaft having the same mechanical properties. The numerical simulation allowed us to determine the natural frequencies and the critical speeds of the composite shaft systems are compared with those available in the literature and the effectiveness of the methods used are discussed.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2011년도 제37회 추계학술대회논문집
• /
• pp.977-980
• /
• 2011

본 논문에서는 항공우주연구원에서 개발중인 1단 저압 축류압축기 성능시험리그의 개발에 대한 내용을 소개하고자 한다. 성능시험리그는 유동 입구부, 동익단, 정익단, 축, 리그 하우징, 베어링 하우징 및 유동 출구부로 구성되어 있다. 로터와 회전축을 단순화하여 회전동역학 해석 결과를 바탕으로 회전축을 설계하고 입 출구 유로의 유동해석을 통해서 시험리그 형상설계를 최적화하였다.