• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08a
• /
• pp.733-736
• /
• 2007

We have proposed novel bonding technique of substrates for developing the flexible LCD with high quality. The gel type mixture of agarose and UV curable epoxy developed to obtain tight bonding ability and enhanced electro-optical characteristic simultaneously. This technique can be used to roll-to-roll process for fabricating the flexible LCDs.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.17 no.2
• /
• pp.23-29
• /
• 2008

This study analyzes the rolled circular rod strip with radius of loom and length of 350cm by using finite element analysis. The material strength and its durability of the rolled strip can be predicted through this study. As the penetration tolerance by contact decreases, the contact rigidity of strip increases. As the contact rigidity becomes the highest at the elapsed time of 1.2 second, the contact stress becomes the lowest. On the contrary, von-Mises stress becomes highest at this time. The total deformation on strip increases from the upper part of strip at the position near to rotating roll to the lower part of strip at the position near to fixing roll.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.540-541
• /
• 2006

SUS316L stainless steel, commercial pure Titanium and Ti-6Al-4V alloy powders applied by Mechanical Milling (MM) process are sintered by Hot Roll Sintering (HRS) process. Microstructure and mechanical properties of those HRS materials is investigated. The microstructures of materials produced by HRS process consist of fine grains and work-hardened structure, that is, the hybrid microstructure. Tensile test of the HRS material demonstrated the good mechanical properties. These results show that the HRS process is very effective to the improvement of mechanical properties in the SUS316L stainless steel, commercial pure Titanium and Ti-6Al-4V alloy.

• Journal of Sensor Science and Technology
• /
• v.29 no.3
• /
• pp.201-204
• /
• 2020

In this study, we fabricated and evaluated graphene composite based 3D scaffolds and planar films. The hybrid composite was prepared by mixing a calculated amount of graphene nanopowder and polydimethylsiloxane in tetrahydrofuran solution. The hybrid composite is easy to manufacture into various forms using direct printing technology or a pressing method. A 3D scaffold structure was prepared at ambient temperature with a flow rate of 240 mm/min. The nozzle pressure was maintained at 350 kPa by adjusting the viscosity of the composite material. The planar film was prepared at different thicknesses using a roll-to-roll equipment. The prepared hybrid nanocomposites were evaluated to investigate their electrical properties according to temperature and mechanical deformation. The obtained results were consistent with each other. Therefore, it can be used effectively as sensors through shape definition.

• Journal of the Korean Society for Precision Engineering
• /
• v.10 no.2
• /
• pp.40-47
• /
• 1993

To diversify the area of application of UBET to the analysis of ring rolling which produces rings having more complex cross-sectional configuration, an element of triangular cross-section has been introduced and the corresponding kinematically admissible velocity field has been derived while considering the material flow between neighboring elements. The theoretical perdictions in roll torque and profile formation show good agreement with the experiments. The effect of process parameters such as feed rate and taper angle of the roll groove has been discussed.

• Transactions on Electrical and Electronic Materials
• /
• v.7 no.1
• /
• pp.1-6
• /
• 2006

Hot carrier degradation and roll off characteristics of threshold voltage ($V_{t1}$) on NMOSFETs as I/O transistor are studied as a function of Lightly Doped Drain (LDD) structures. Pocket dose and the combination of Phosphorus (P) and Arsenic (As) dose are applied to control $V_{t1}$ roll off down to the $10\%$ gate length margin. It was seen that the relationship between $V_{t1}$ roll off characteristic and substrate current depends on P dopant dose. For the first time, we found that the n-p-n transistor triggering voltage ($V_{t1}$) depends on drain current, and both $I_{t2}$ and snapback holding voltage ($V_{sp}$) depend on the substrate current by characterization with a transmission line pulse generator. Also it was found that the improved lifetime for hot carrier stress could be obtained by controlling the P dose as loosing the $V_{t1}$ roll off margin. This study suggests that the trade-off characteristic between gate length margin and channel hot carrier (CHC) lifetime in NMOSFETs should be determined by considering Electrostatic Discharge (ESD) characteristic.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.9
• /
• pp.879-884
• /
• 2015

Printed electronics is a technology that produces electronic devices and circuits by printing functional ink on a web, which is a film-like flexible material. This technology is suitable for large-scale and high-speed mass production, and is a next-generation process technology that can fabricate electronic devices from flexible materials. As precise measurement of the positions of the web is required in order to commercialize such a printed electronics process, a measurement system with an optical encoder with a precision of micrometers had been proposed in the preceding research of this study. However, the lateral positions of the web could not be measured in the preceding research as the phenomenon of the entire web being moved in the lateral direction could not be detected. In this study, a measurement system that utilizes the differences in the amount of light reflected from the alignment patterns depending on the web positions in the lateral direction was proposed for measuring the lateral positions of the web. In addition, its reliability was verified and then the effect when measuring printed alignment patterns was analyzed by experiments.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.2
• /
• pp.263-272
• /
• 2013

Printed electronics creates electrically functional devices by printing on variety of substrates. Printing typically uses common printing equipment or other low-cost equipment suitable for defining patterns on material, such as screen printing, flexography, gravure, offset lithography and inkjet. Compared to conventional manufacturing of microelectronics, printed electronics is characterized by simpler and more cost-effective fabrication of high and low volume products. Now there is huge effort towards printing many other more functional components, from displays to transistors to photovoltaic cells, using the full range of printing technologies - from inkjet to roll to roll analogue print techniques. The market for printed electronics will rise from $1.99 billion in 2010 to $55.10 billion in 2020. In 2030, this industry could be $300 billion - larger than the silicon semiconductor industry - from lighting to displays[8].

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.9
• /
• pp.1299-1304
• /
• 2010

We examined the working fracture behavior of a silicon-steel strip caused by deformation deviation by performing a pilot rolling test. The deformation deviation resulted in the edges (or center portion) of the strip being stretched and the other parts being compressed in the rolling direction; this was because of different degrees of deformation in these parts. We designed roll grooves shape to reflect the role of roll bending, which generates waviness in the strip in an actual cold rolling process, into the pilot rolling test. The material used in the rolling test was highsilicon steel (about 3%). The results of the test showed that the type of fracture in the strip specimen varied with the magnitude of the deformation deviation. The tensile stress produced at the strip edges because of the center waviness in the rolling direction was a crucial factor that resulted in edge cracking and a zigzag-shaped fracture at the center.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.05a
• /
• pp.59-72
• /
• 1999

In this thesis, we measured the Barkhausen effect of CoFeSiB amorphous ribbon and then investigated its possibility to be used as a sensor material. We used a sample of composition $($Fe_{0.06}$$Co_{0.94}$)_${0.79}$$Si_{2.1}$$B_{18.9}$ with a thickness 12[pm1, width 2.5[rnml and length 5[cm], which was fabricated by a single roll method. In order to improve magnetic characteristics of the sample, we had carried on annealing in the magnetic field and in none magnetic field. And, experimented results to the magnetic characteristics show that the ribbon has large Barkhausen jump even in weak magnetic field below 0.5[0el. From the results, we confirmed that the sample can be used as an magnetic sensor material.