• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.58 no.4
• /
• pp.541-545
• /
• 2009

This study evaluated the contact resistance, insulation resistance, withstand voltage characteristics and insertion force, etc., of the wire connector used inside an integrated LITE WAY lighting fixture developed for efficient installation. Since the connector connecting the lighting fixture's internal wires is housed, it is easily connected and separated and has a structure enabling a close-fitting connection. The temperature and time applied to the high temperature characteristics test of the connector are $105^{\circ}C$ and 16 hours, respectively. The measured contact resistance of the high temperature tested connector was 3.258 mV/A, and its measured insulation resistance was greater than $10\;G{\Omega}$ All specimens demonstrated uniform insulation characteristics, which could be seen to be in good condition. From the withstand voltage test results found before and after performing the high temperature operation test on the connector for cable connection, it was confirmed that the withstand voltage characteristics between all terminals were good. The insertion force of the connector connecting the internal wiring averaged 9.67 kgf. It was observed that the insertion force between the plug housing and the female terminal, and that between the plug housing and the male terminal, were 0.680 kgf and 1.27 kgf on average, respectively.

• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 2002.03a
• /
• pp.67-74
• /
• 2002

An experimental assessment on the dynamic behavior of saturated sand which can consider the irregular characteristics of earthquakes was proposed. The equivalent uniform stress concept presented by Seed and Idriss has been applied to evaluate the liquefaction resistance strength to simplify earthquake loading. However, it was known that the liquefaction resistance strength of soil based on the equivalent uniform stress concept can't exactly mirror the dynamic characteristics of the irregular earthquake motion. In this study, estimation of the criterion of the liquefaction resistance strength was determined by applying real earthquake loading to the cyclic triaxial test. From the test results, relationships between excess pore water pressure and the earthquake characteristics such as magnitude or duration were determined. Magnitude scaling factors to determine the soil liquefaction resistance strength in seismic design were also proposed.

• Journal of Ocean Engineering and Technology
• /
• v.28 no.6
• /
• pp.493-499
• /
• 2014

The resistance performances were studied for two 50-ft-class power yachts made of carbon fiber reinforced plastic (CFRP) with different hull form characteristics using model tests. The tests were carried out at a high-speed circulating water channel (CWC) for the 16–38 knot range. The total resistance, trim, and sinkage were measured, and the results were compared with wave patterns. The results showed that a chine position at the draft line had a strong effect on the planning performance and resistance performance in a certain velocity range.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.8
• /
• pp.688-692
• /
• 2003

For high voltage operation, a new type of piezoelectric transformer using radial vibration of disk, poled with the same direction was proposed. The piezoelectric ceramics was composed to PZT-PMN-PSN. The diameter and thickness of a disk type piezoelectric transformer were 45［mm］and 4［mm］, respectively The surface ratio of driving electrode and generating electrode of the piezoelectric transformer was 2 : 1. The resonance characteristics of input admittance, step-up voltage ratio and power transmission efficiency of the piezoelectric transformer were measured by varying the load resistance(0.1∼70［kΩ］). As a result, both resonance frequency and step-up voltage ratio increased with increasing load resistance. The step-up voltage ratio was reached more than 60 times under no load resistance. The maximum efficiency of 97% at load resistance of 2kΩ was obtained.

• Journal of the Semiconductor & Display Technology
• /
• v.18 no.2
• /
• pp.29-31
• /
• 2019

The ZTO/p-Si thin film was produced and investigated for tunneling phenomena caused by the interface characteristics of the depletion layer. ZTO thin film was deposited and heat treated to produce barrier potentials by the depletion layer. The negative resistance characteristics were shown in the thin film of ZTO heat treated at $100^{\circ}C$, and the insulation properties were the best. Current decreased in the negative voltage direction by nonlinear show key characteristics, and current decreased in tunneling phenomenon by negative resistance in the positive voltage direction. Heat treated at $100^{\circ}C$, the ZTO thin film has increased barrier potential in the areas of the depletion layer and therefore the current has increased rapidly. The current has decreased again as we go beyond the depletion layer. Therefore, tunneling can be seen to make insulation better. In the ZTO thin film heat treated at $70^{\circ}C$ without tunneling, leakage current occurred as current increased at positive voltage. Therefore, tunneling effects by negative resistance were found to enhance insulation properties electrically.

• Proceedings of the KIEE Conference
• /
• 1996.07c
• /
• pp.1609-1611
• /
• 1996

The on-resistance characteristics of the RESURF LDMOS and VDMOS are compared. The on-resistance vs. breakdown characteristics of the RESURF LDMOS is analytically investigated. The on-resistance of RESVRF LDMOS is as almost same as that of VDMOS.

• 전기의세계
• /
• v.29 no.2
• /
• pp.111-117
• /
• 1980

Contacts formed by vacuum evaporation of As-Te-Si-Ge chalcogenide glass onto Al metal (99.9999%) are studied by measuring paralle capacitance C(V), Cp(w), resistance R(V), Rp(w), and I-V characteristics. The fact that contact metal alloying produced high-resistance region is confirmed from the measurements of parallel capacitance and resistance. From the I-V characteristics in the pre-switcing region, it is found that electronic conduction and sitching occurs in the vicinity of metal-amorphous semiconductor interface. From the experimental obsevations, it is concuded that the current flow in the thin film is space-charge limited current (SCLC) due to the tunneling of electrons through the energy barriers.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.20 no.6
• /
• pp.491-497
• /
• 2015

This study proposes a new control method for a resistance spot welding inverter to improve weld quality. The proposed method is based on the dynamic resistance characteristics of steel sheets to be welded. A point in the second peak value of the dynamic resistance occurs during one shot of the welding current flow. A constant voltage control is applied from zero to the peak point, and a constant current control is adopted from the peak point to the end of the shot. The mixed mode control of the constant voltage and current guarantees high weld quality. Experiments are conducted with a 5 kA power supply and 0.5 mm steel sheets to compare quality. Experimental results show that weld quality is improved more than 10 times that of the conventional control method.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.5
• /
• pp.113-118
• /
• 2008

We have developed an integrated giant magneto resistance using not only circuit but also integrating technique with semiconductor for automobile application. It has four elements used for giant magneto resistance sensor. Ni-Fe/Cu multi layers were prepared on a glass substrate by magnetron sputtering. The dependence of magneto resistance on the thickness of the Ni-Fe and Cu layers was investigated. The MR ratio showed a saturated a peak at Cu layer $10{\AA}$, Ni-Fe layer $50{\AA}$, where the MR ratio is about 8.7% at room temperature. By means of Ni-Fe multi film and specific integrating technique, these new giant magneto resistance sensor showed excellent resistance characteristics.

• Journal of Information Technology Applications and Management
• /
• v.10 no.1
• /
• pp.47-59
• /
• 2003

This study analyses the level of resistance which workers have against the adoption of ERP systems and the factors affecting the resistance to the adoption of the new systems. The major results of the study include 1) about 40% of workers showed resistance to the adoption of ERP systems, and 2) all six factors (technical characteristics of ERP system, functional characteristics of ERP system, implementation approach, task changes caused by the adoption of ERP system, attitude toward change, and altitude toward organization) were proved to affect the resistance to the adoption of the ERP systems. In practice, adoption of ERP system brings significant changes to workers. In order for an organization to succeed, it is necessary to reduce the resistance of workers. Since this study is performed based on a case study, the results of the study may not be generalized. However, the results of the study may provide guidance which organizations can refer in the course of effective personnel management.