• 한국화재소방학회논문지
• /
• 제30권6호
• /
• pp.99-104
• /
• 2016

본 논문에서는 동식물시설 중 전기화재 비율이 높은 우사, 계사, 돈사에서 먼지샘플을 채취하여 증류수에 희석시킨 후 이 물의 저항률을 측정하고, 저항률에 따른 물의 온도변화 및 전류 측정실험, 트래킹 재현실험을 통해 축사별로 먼지에 따른 트래킹화재 위험성을 분석하였다. 분석결과 저항률 수치는 우사, 계사, 돈사 순으로 돈사가 가장 낮게 측정되었으며, 축사별 평균 값 역시 우사, 계사, 돈사 순으로 돈사가 가장 낮게 나타났다. 온도변화 및 전류 측정실험에서는 저항률이 낮을수록 물의 온도변화가 큰 경향을 보였으며, 전류 실효값 역시 높게 나타났다. 트래킹 재현실험에서도 저항률이 낮을수록 트래킹 진전속도가 빠르게 진행되었으며 착화시간이 단축되었다. 실험결과를 통해 도출된 결과를 가지고 축사별 먼지 저항률이 다른 이유를 고찰하였다.

• Smart Structures and Systems
• /
• 제22권2호
• /
• pp.185-192
• /
• 2018

Participants in the Asia Pacific Conference of the Prognostics and Health Management Society 2017 (PHMAP 2017) Data Challenge were given measured vibration signals from motor-driven gearboxes used in pulverizers. Using this information, participants were requested to predict failure dates and the faulty components. The measured signals were affected by significant noise and disturbance, as the pulverizers in the provided data worked under actual operating conditions. This paper thus presents a fault prediction method for a motor-driven gearbox in a pulverizer system that can perform under external noise and disturbance conditions. First, two fault features, an RMS value in the higher frequency zones (HRMS) and an amplitude of a period for high-speed shaft in the quefrency domain ($QA_{HSS}$), were extracted based on frequency analysis using the higher and lower sampling rate data. The two features were then applied to each pulverizer based on results of frequency responses to impact loadings. Then, a regression analysis was used to predict the failure date using the two extracted features. A weighted regression analysis was used to compensate for the imbalance of the features in the given period. In addition, the faulty components in the motor-driven gearboxes were predicted based on the modulated frequency components. The score predicted by the proposed approach was ranked first in the PHMAP 2017 Data Challenge.

• Computers and Concrete
• /
• 제20권5호
• /
• pp.545-553
• /
• 2017

A pounding tuned mass damper (PTMD) can be considered as a passive device, which combines the merits of a traditional tuned mass damper (TMD) and a collision damper. A recent analytical study by the authors demonstrated that the PTMD base on the energy dissipation during impact is able to achieve better control effectiveness over the traditional TMD. In this paper, a PTMD prototype is manufactured and applied for seismic response reduction to examine its efficacy. A series of shaking table tests is conducted in a three-story building frame model under single-dimensional and two-dimensional broadband earthquake excitations with different excitation intensities. The ability of the PTMD to reduce the structural responses is experimentally investigated. The results show that the traditional TMD is sensitive to input excitations, while the PTMD mostly has improved control performance over the TMD to remarkably reduce both the peak and root-mean-square (RMS) structural responses under single-dimensional earthquake excitation. Unlike the TMD, the PTMD is found to have the merit of maintaining a stable performance when subjected to different earthquake loadings. In addition, it is also indicated that the performance of the PTMD can be enhanced by adjusting the initial gap value, and the control effectiveness improves with the increasing excitation intensity. Under two-dimensional earthquake inputs, the PTMD controls remain outperform the TMD controls; however, the oscillation of the added mass is observed during the test, which may induce torsional vibration modes of the structure, and hence, result in poor control performance especially after a strong earthquake period.

• Journal of Advanced Marine Engineering and Technology
• /
• 제33권5호
• /
• pp.672-678
• /
• 2009

Acoustic Emission (AE) technique is a non-destructive testing method and widely used for the early detection of faults in rotating machines in these days, because the sensitivity of AE transducers is higher than normal accelerometers. So it can detect low energy vibration signals. The faults in the rotating machines are generally occurred at bearings and gearboxes which are the principal parts of the machines. It was studied to detect the bearing faults by envelop analysis in several decade years. And the researches showed that AE had a possibility of the application in condition monitoring system(CMS) using the envelope analysis for the rolling bearing. And peak ratio (PR) was developed for expression of the bearing condition in condition monitoring system using AE. Noise level is needed to reduce to take exact PR value because the PR is calculated from total root mean square (RMS) and the harmonics peak levels of the defect frequencies of the bearing. Therefore, in this paper, the discrete wavelet transform (DWT) was added in the envelope analysis to reduce the noise level in the AE signals. And then, the PR was calculated and compared with general envelope analysis result and the result of envelope analysis added the DWT. In the experiment result about inner fault of bearing, defect frequency was difficult to find about only envelop analysis. But it's easy to find defect frequency after wavelet transform. Therefore, Envelop analysis added wavelet transform was useful method for early detection of default in signal process.

• 한국표면공학회지
• /
• 제38권5호
• /
• pp.188-192
• /
• 2005

Indium zinc oxide (IZO) thin films were deposited on glass substrate by dc magnetron sputtering. The effects of oxygen flow rate and deposition temperature on electrical and optical properties of the films were investigated. With addition of small amount of oxygen gas, the characteristic properties of amorphous IZO films were improved and the specific resistivity was about $4.8{\times}10^{-4}\Omega{\cdot}cm$. Change of structural properties according to the deposition temperature was observed with XRD, SEM, and AFM. Films deposited above $300^{\circ}C$ were found to be polycrystalline. Surface roughness of the films was increased due to the formation of grains on the surface. Electrical conductivity became deteriorated for polycrystalline IZO films. Consequently, high quality IZO films could be prepared by do sputtering with $O_{2}/Ar{\simeq}0.03$ and deposition temperature in range of $150\~200^{\circ}C$; a specific resistivity of $3.4{\times}10^{-4}{\Omega}{\cdot}cm$, an optical transmission over $90\%$ at wavelength of 550 nm, and a rms value of surface roughness about $3{\AA}$.

• 대한기계학회논문집A
• /
• 제41권3호
• /
• pp.213-218
• /
• 2017

리모트 용접용 2D 스캐너 F-theta 렌즈의 역설계가 광선 추적기법을 사용하여서 수행이 되었다. 렌즈의 곡면 및 렌즈간 거리를 변수로 설정하고 초점거리를 Marginal Ray Height 로 설정하여, 상용 광선추적기법 프로그램을 사용하여 무한반복 최적화를 수행 하였다. 최종목표 값을 설정 후 Merit Function에 정의된 기준에 따라, 최종 초점거리와 초점의 크기를 최종 목표 값 가중치로 설정하였다. 최적화된 렌즈는 총 4매이며, 벤치마킹된 상용렌즈의 초점거리(185mm) 보다는 다소 근거리인 137mm로 최적화 되었지만, 초점의 크기는 레이저 입사각에 따라 RMS 기준 $1.3{\mu}m$, $6.2{\mu}m$ 그리고 $16.1{\mu}m$로 계산 되었으며, 이는 상용렌즈에 근접하는 성능을 구현한다. 입사각별 왜곡도를 중첩 하여서 비교 분석한 결과, 입사각 $0^{\circ}$와 $12.5^{\circ}$에서는 기존 렌즈와 거의 유사한 형태로 나타나는 것을 볼 수가 있어, 본 연구에서 제안된 역설계기법이 사용자 환경에 따라서 효과적으로 적용되어 최적설계가 이루어질 수 있을 것으로 기대가 된다.

• 대한기계학회논문집A
• /
• 제36권7호
• /
• pp.823-828
• /
• 2012

연식주퇴 메커니즘은 전방 운동량으로 주퇴력을 감소시키는 메커니즘이다. 연식주퇴 메커니즘에 영향을 미치는 매개변수는 사격 각도, 복좌기의 초기 압력, 발사위치등과 같이 다양하게 존재한다. 이런 매개변수들은 연식주퇴 메커니즘에서 전방 운동량을 결정짓는 요소가 된다. 연식주퇴 메커니즘의 설계를 위해 몇 가지 적당한 조건들을 고려하여 전방 운동량에 영향을 미치는 매개변수들에 대해 연구하였다. 여러 가지 매개변수들 중에서 복좌기의 초기 압력과 사격 위치가 전방 운동량에 영향을 미치는 중요한 요소로 확인하였다. 복좌기의 초기 압력이 180 일 때, 주퇴력이 가장 낮은 값을 가진다.

• 한국해안·해양공학회논문집
• /
• 제32권5호
• /
• pp.363-371
• /
• 2020

우리나라 동해 남항진 해역에서 관측한 고파 파랑 스펙트럼 정보를 이용하여 수정 BM 스펙트럼과 JONSWAP 스펙트럼의 매개변수를 추정하였다. BM 스펙트럼의 매개변수 추정결과는 1.04, 0.27로 대푯값으로 제시된 1.098, 0.30과 유사하였으나 통계적으로는 유의미한 차이를 보였다. 한편 JONSWAP 스펙트럼의 경우에는 첨두증대계수의 값이 통상적으로 적용되는 값인 3.3보다 매우 작은 1.4로 추정되었다. 두 스펙트럼의 적합 RMS 오차 차이는 0.2 정도로 미미한 수준이었으나, 두 스펙트럼 모두 첨두주파수보다 큰 주파수 영역에서의 에너지가 표준 스펙트럼 형태에 비해 상대적으로 완만하게 감소하는 양상을 보였다.

• 대한치과보철학회지
• /
• 제44권4호
• /
• pp.443-454
• /
• 2006

Purpose: This study aims to get the fundamental data which is necessary to the development direction of implant surface treatment hereafter, based on the understanding the surface structure and properties of titanium which is suitable for the absorption of initial tissue fluid by researching effects of additional surface treatments fir sandblasted with large git and acid-etched(SLA) titanium on surface micro-roughness, static wettability, fibronectin adsorption Materials and Method: In the Control groups, the commercial pure titanium disks which is 10mm in diameter and 2mm in thickness were treated with HCI after sandblasting with 50$\mu$m $Al_2O_3$. The experiment groups were made an experiment each by being treated with 1) 22.5% nitric acid according to SLA+ASTM F86 protocol, 2) SLA+30% peroxide, 3) SLA+NaOH, 4) SLA+ Oxalic acid, and 5) SLA+600$^{\circ}C$ heating. In each group, the value of Ra and RMS which are the gauges of surface roughness was measured, surface wettability was measured by analyzing with Sessile drop method, and fibronectin adsorption was measured with immunological assay. The significance of each group was verified by (SPSS, ver.10.0 SPSS Inc.) Kruskal-Wallis Test. (α=0.05) And the correlation significance between Surface micro-roughness and surface wettability. surface roughness and fibronectin adsorption, and surface wettability and fibronectin adsorption was tested by Spearman's correlation analysis. Result: All measure groups showed the significant differences in surface micro-roughness, surface wettability, and fibronectin adsorption. (p<0.05) There was no significance in correlation among the surface micro-roughness, surface wettability, and fibronectin adsorption. (p>0.05) Conclusion: Surface micro-roughness and surface wettability rarely affected the absorption of initial tissue fluid on the surface of titanium.

• 대한치과기공학회지
• /
• 제39권3호
• /
• pp.137-143
• /
• 2017

Purpose: The purpose of this study is to analyze the fitness of heat - pressed ceramic laminate veneers fabricated using the additive manufacturing. Methods: Impression was replicated by using light body silicone and heavy body silicone on the custom tray, and it was fabricated using Type IV Stone. The test specimens were prepared by using a dental scanner, a laminating veneer using a dental design program, and a specimen with a 3D printer. The control specimens were prepared by the lost wax technique and heat - pressed to fabricate the specimens. The data of the specimens were measured by the RMS value of the internal fitness a using a 3-dimensional measurement program. Results: The Stereolithography laminate veneer group was measured at $78.10(4.09){\mu}m$ and the LWV group was measured at $31.50(5.10){\mu}m$. There is a significant difference between the two groups (p<0.001) Conclusion : Evaluation of fitness laminate veneers was fabricated by additive manufacturing showed the difference statistically significantly and clinically acceptable result.