• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.9 no.6
• /
• pp.1269-1276
• /
• 2005

In this paper, Mixer using the direct-conversion method intended to use in front-end of a RF receiver is designed. The direct conversion Mixer is an alternative wireless receiver architecture to the well-established superheterodyne, particularly for high integration, low power, and low cost. It operates at 2.4GHz band, and is designed and simulated with a 0.35um CMOS technology and HSPICE simulator. Layout is implemented with a Mentor IC Station. The 2.4GHz CMOS Mixer employs a modified single-balanced Gilbert Cell with additional MOSFET in the output stages to improve IIP2, which is a standard of linearity in direct conversion receiver. Additional coversion-stages's transconductances are controlled by each MOSFET's physical properties. The HSPICE simulation results show that the 2.4GHz CMOS Mixer has voltage gam of 29dB, IIP2 of 63dBm, respectively. The Mixer also draws 3.5mA from a 3.3V supply.

• Journal of IKEEE
• /
• v.7 no.2 s.13
• /
• pp.236-244
• /
• 2003

In this paper, RF and IF circuits for mobile terminals which have usually been implemented using expensive BiCMOS processes are designed using CMOS circuits, and a Tx CMOS RF/IF single chip for PCS applications is designed. The designed circuit consists of an IF block including an IF PLL frequency synthesizer, an IF mixer, and a VGA and an RF block including a SSB RF mixer and a driver amplifier, and performs all transmit signal processing functions required between digital baseband and the power amplifier. The phase noise level of the designed IF PLL frequency synthesizer is -114dBc/Hz@100kHz and the lock time is less than $300{\mu}s$. It consumes 5.3mA from a 3V power supply. The conversion gain and OIP3 of the IF mixer block are 3.6dB and -11.3dBm. It consumes 5.3mA. The 3dB frequencies of the VGA are greater than 250MHz for all gain settings. The designed VGA consumes 10mA. The designed RF block exhibits a gain of 14.93dB and an OIP3 of 6.97dBm. The image and carrier suppressions are 35dBc and 31dBc, respectively. It consumes 63.4mA. The designed circuits are under fabrication using a $0.35{\mu}m$ CMOS process. The designed entire chip consumes 84mA from a 3V supply, and its area is $1.6㎜{\times}3.5㎜$.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.8
• /
• pp.632-639
• /
• 2018

This paper presents a single antenna radar sensor with a Ku-band radar transceiver IC realized by 130 nm CMOS processes. In this radar receiver, sensitivity time control using a DC offset cancellation feedback loop is employed to achieve a constant SNR, irrespective of distance. In addition, the receiver RF block has gain control to adjust high dynamic range. The RF output power is 9 dBm and the full chain gain of the Rx is 82 dB. To reduce the direct-coupled Tx signal to the Rx in a single antenna radar, a stub-tuned hybrid coupler is adopted instead of a bulky circulator. The maximum measured distance between the horn antenna and a metal plate target is 6 m.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.35S no.9
• /
• pp.9-18
• /
• 1998

A single RF transceiver chip for an extended GSM handset application was designedm, fabricated and evaluated. A RFIC was fabricated by using silicon BiCMOS process, and then packaged in 80 pin TQFP of $10 {\times} 10 mm^{2}$ in size. As a result, it was achieved guite reasonable integraty and good RF performance at the operation voltage of 3.3V. This paper describes development results of RF receiver section of the RFIC, which includes LNA, down conversion mixer, AGC, switched capacitor filter and down sampling mixer. The test results show that RF receiver section is well operated within frequency range of 925 ~960 MHz, which is defined on the extended GSM specification (E-GSM). The receiver section also reveals moderate power consumption of 67 mA and minimum detectable signal of -105 dBm.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.5 no.4
• /
• pp.367-370
• /
• 2004

We fabricated SiGe BiCMOS devices, which are important for ultra high speed RF IC chips, by employing $0.35\mu{m}$ CMOS process. To meet with the requirement of low noise level with linear base leakage current at low VBE region, we try to minimize polysilicon/ silicon interface traps by optimizing capping silicon thickness and EDR(emitter drive-in RTA) temperature. We employed $200\AA$and $300\AA$-thick capping silicon, and varied the EDR process condition at temperature of $900-1000^\circ{C}$, and time of 0-30 sec at a given capping silicon thickness. We investigated current gain behavior at each process condition. We suggest that optimum EDR process condition would be $975^\circ{C}$-30 sec with $300\AA$-thick capping silicon for proposed $0.35\mu{m}$-SiGe HBT devices.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.9 no.4
• /
• pp.257-265
• /
• 2009

Recent progress in development of CMOS power amplifiers for mobile terminals is reviewed, focusing first on switching mode power amplifiers, which are used for transmitters with constant envelope modulation and polar transmitters. Then, various transmission line transformers are evaluated. Finally, linear power amplifiers, and linearization techniques, are discussed. Although CMOS devices are less linear than other devices, additional functions can be easily integrated with CMOS power amplifiersin the same IC. Therefore, CMOS power amplifiers are expected to have potential applications after various linearity and efficiency enhancement techniques are used.

• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.2
• /
• pp.44-52
• /
• 2002

본 논문에서는 RF와 마이크로파 응용을 위한 MEMS 수동 소자에 대한 내용이다. 이 수동 소자들을 만들기 위해서 개발된 3타원 MEMS공정은 기존의 실리콘 공정과 완전한 호환성을 가지고 한 칩으로 집적화 시킬 수 있는 공정이다. 이 3차원 MEMS 공정은 기존 실리콘 긍정이 가지고 있는 한계를 극복하기 위한 방법으로써 개발되었다. 개발된 공정을 이용하여 실리콘 공정에서 구현할 수 없었던 좋은 성능의 인덕터, 트랜스포머 및 전송선을 RF와 마이크로파 응용을 위해서 구현하였다. 저 전압, 높은 차단율을 위한 push-pull 개념을 도입한 MEMS 스위치를 구현하였다. 또한 높은 Q를 갖는 MEMS 인덕터를 최초로 CMOS 칩과 집적화에 성공하여 600kHz 옵셋 주파수에서 -122 dBc/Hz의 특성을 갖는 2.6 GHz 전압 제어 발진기를 제작하였다.

• Electronics and Telecommunications Trends
• /
• v.25 no.5
• /
• pp.97-105
• /
• 2010

모바일과 유비쿼터스 센서 네트워크 센서 시대가 도래함에 따라 가볍고, 작고, 얇고, 멀티기능을 구현할 수 있는 부품에 대한 요구가 증대하고 있다. 이에 대한 여러 가지 솔루션 중 MCM의 개념을 수직 방향으로 확장시킨 3D IC가 최근 각광을 받고 있다. 이는 물리적인 한계에 부딪힌 반도체 집적 공정의 한계를 극복하여 지속적으로 무어의 법칙에 맞춰 집적도를 향상시킬 수 있을 뿐만 아니라 소재와 공정이 달라도 3차원적으로 집적이 가능하여 메모리와 프로세서로 대표되는 디지털 칩뿐만 아니라 아날로그/RF, 수동소자, 전력소자, 센서/액추에이터, 바이오칩 등을 하나로 패키징 할 수 있는 장점이 있기 때문이다. 이를 통해 성능 향상, 경박단소, 저비용의 부품 개발이 가능하기 때문에 미국, 유럽, 일본 등 선도국뿐만 아니라 싱가포르, 타이완, 중국 등에서도 활발한 연구가 진행되고 있으며 CMOS 이미지 센서 모듈 생산에 TSV 기술이 이미 적용되고 있다. 본 고에서는 3D IC를 위한 TSV 및 적층 요소 기술을 소개하고 이를 통해 개발된 사례와 표준화 동향에 대하여 소개하고자 한다.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.4 no.3
• /
• pp.196-203
• /
• 2004

A three-dimensional (3D) IC technology platform is presented for high-performance, low-cost heterogeneous integration of silicon ICs. The platform uses dielectric adhesive bonding of fully-processed wafer-to-wafer aligned ICs, followed by a three-step thinning process and copper damascene patterning to form inter-wafer interconnects. Daisy-chain inter-wafer via test structures and compatibility of the process steps with 130 nm CMOS sal devices and circuits indicate the viability of the process flow. Such 3D integration with through-die vias enables high functionality in intelligent wireless terminals, as vertical integration of processor, large memory, image sensors and RF/microwave transceivers can be achieved with silicon-based ICs (Si CMOS and/or SiGe BiCMOS). Two examples of such capability are highlighted: memory-intensive Si CMOS digital processors with large L2 caches and SiGe BiCMOS pipelined A/D converters. A comparison of wafer-level 3D integration 'lith system-on-a-chip (SoC) and system-in-a-package (SiP) implementations is presented.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.15 no.5
• /
• pp.485-489
• /
• 2015

An accurate large-signal BSIM4 macro model including new empirical bias-dependent equations of the drain-source capacitance and channel resistance constructed from bias-dependent data extracted from S-parameters of RF MOSFETs is developed to reduce $S_{22}$-parameter error of a conventional BSIM4 model. Its accuracy is validated by finding the much better agreement up to 40 GHz between the measured and modeled $S_{22}$-parameter than the conventional one in the wide bias range.