• Journal of KSNVE
• /
• v.10 no.2
• /
• pp.299-305
• /
• 2000

In this study, the characteristics of transmitted vibration on hand-arm system are examined when operating electric hand tools. Also through the correlation analysis between anthroponetric data and transmitted vibration, and comparison study with appropriate amount of work done based on the ISO criteriaa, the basic data for the ergonomic work design can be presented. The types of electric tools and works for the experiment are drill (general type and impact type), grinder, wire brush and steel to analyze the characteristics of transmitted vibrations, the amount of transmitted vibrations in X, Y and Z direction at tool(T), hand(H), wrist(W), and the joint between foream and upper arm(A) were measured at the frequency range of 6.3∼1000[HZ]. Also, the limit of human exposure to vibration, and the response of frequency were conducted.

• Journal of KSNVE
• /
• v.10 no.2
• /
• pp.325-330
• /
• 2000

A dynamic absorber is used to protect the primary vibration system under the steady-state harmonic disturbance. In a number of cases it appears expedient to install several absorbers of smaller masses instead of one. This may be due to the need of distribute the absorber's response along the construction, restrictions on the absorber's installation. So, we studied characteristics of the primary vibration system for the optimal natural frequency ratio and the optimal damping ratio of serial multi-dynamic absorber. Also we obtained the optimum values of the serial multi-dynamic absorber parameters using computer simulation for the damped primary vibration system. In designing multi-dynamic absorber, we presented for the optimal natural frequency and the optimal damping ratio of multi-dynamic absorbers.

• Journal of KSNVE
• /
• v.10 no.3
• /
• pp.451-456
• /
• 2000

In this paper a discrete time model for the identification of nonlinear vibration system with stick-slip friction is proposed. The proposed model can handle the highly nonlinear behavior of the friction such as stick-slip phenomenon and Stribeck effect. The basic idea of the proposed model is as follows : If the nonlinearity of the system can be predicted as a simple function then this nonlinear function term cab be directly used in the discrete time model. By doing this the number of nonlinear terms in the model can be much less than those of NARMAX model which is widely used nonlinear discrete model. The simulation result shows that the proposed model can estimate the response of the nonlinear vibration system with stick-slip friction very well with less computational effort.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.4
• /
• pp.181-188
• /
• 2000

Input shaping is a method fur reducing residual vibration. Vibration is eliminated by convolving an input shaper, which is a sequence of impulses, with the desired system command. It has been applied to robot with a flexible manipulator. But it can be applied to the reduction of residual vibration far overhead crane. In this paper, input shaping shows good performance for anti-sway of overhead crane. In the z-domain, we designed an input shaper and calculated the sensitivity of it. If sensitivity is calculated in the z-domain, the shapes of sensitivity curves are expected easily. Accordingly, it is easy to design an input shaper in the z-domain. We compared the response of a system with shaper to it without that. Also, we compared El shaper to ZV shaper in view of robustness.

• Proceedings of the KSRS Conference
• /
• 2003.11a
• /
• pp.1483-1485
• /
• 2003

Multitemporal approaches using sequential data acquired over multiple years are essential for satisfactory discrimination between many land cover classes whose signatures exhibit seasonal trends. At any particular time, the response of several classes may be indistinguishable. Using the estimates of periodogram which are obtained from sequential images, the periodicity of the process have been incorporates into multitemporal classification. The Normalized Difference Vegetation Index (NDVI) was computed for seven-day composites of the Advanced Very High Resolution Radiometer (AVHRR) imagery over the Korean peninsula for 1996 - 2000 using a dynamic technique.

• Proceedings of the Korean Statistical Society Conference
• /
• 2000.11a
• /
• pp.97-104
• /
• 2000

Time-related underemployment exists when a person's employment is insufficient in terms of the volume of work. Two alternative definitions can be considered based on a longer-term view or a shorter-term view and these were designed into a single questionnaire. We conducted a pilot sample survey with about 6,000 respondents in Korea. The estimates of underemployment using the two definitions show some differences given the ages, genders, industrial areas and main activities of the respondents. A larger number of people could be identified as underemployed when the longer-term view is used than when the shorter-term view is used, but there is a greater cost associated with the former. The cost-benefit of the interviewers' time was investigated by multiple visits to households. Biases and costs are also analyzed using the results of the comparison of the decrease in non-responses with the increase in the costs for the interviews.

• Near Infrared Analysis
• /
• v.1 no.1
• /
• pp.9-17
• /
• 2000

A variety of standardization methods between two near-infrared (NIR) spectrometers were investigated for the prediction of five constituents in trans-alkylation process. Spectra were collected by two different instruments (one is regarded as mater instrument, other on as slave instrument). Three well-known standardization methods of direct standardization (DS), piecewise direct standardization (PDS) and slope/bias correction of response variable were applied to trans-alkylation samples on the slave instrument. We have examined for a set of reliable standardization samples using smaller number of transfer samples in order to increase efficiency of standardization.

• Agricultural and Biosystems Engineering
• /
• v.1 no.1
• /
• pp.59-62
• /
• 2000

After ten years of implementing the agricultural automation program in Taiwan, some positive effects and satisfactory results have been recognized by both the agricultural industry and local administrative bureaux. The automation of agriculture is a response to sophisticated demands for production and quality in countries with high labor costs. The development of sensor systems, control systems, precision agriculture systems, and engineering for plant culture systems will determine the degree of automation used for crop production in the 21st century. The engineering system will capitalize upon expertise from physiologists, pathologists, systems analysts, agronomists, horticulturists, computer programmers, economists, crop producers and managers in order to efficiently implement automated crop production.

• Proceedings of the Korean Operations and Management Science Society Conference
• /
• 2000.10a
• /
• pp.215-218
• /
• 2000

Workflow Management System(WfMS) enables corporations to manage business processes efficiently The purpose of this research is to develop a management system that is capable of managing complicated business processes efficiently under distributed environment where many companies or divisions are participating. Run-time encapsulation proposed in this paper is a system design methodology that enables appropriate response to the dynamically changing processes by using nested processes. We have implemented WfMS under Web environment using run-time encapsulation. Run-time encapsulation using nested process is an efficient development methodology for implementing heterogeneous and distributed WfMS under web environment.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.2
• /
• pp.151-160
• /
• 2000

An experimental and theoretical analysis for the improvement of dynamic characteristics and design of electro-hydraulic flow control servo valve are performed. The theoretical results are compared with the experimental step responses, and the important design parameters of an electro-hydraulic flow control servo valve are derived by using the simulation program. Simulation parameters of nozzle jet coefficient and orifice and spool valve discharge coefficient are given through experiment. The theoretical and experimental step response curves show that the valve gain depends on the fixed orifice and nozzle $ratio(R_on)$ and is maximum at $R_on=1.$ And drain orifice in the flapper - nozzle return line creates a small back pressure, which improves the performance fur the valve.