• Journal of Mechanical Science and Technology
• /
• v.17 no.10
• /
• pp.1520-1532
• /
• 2003

An experiment was performed to obtain the local heat transfer coefficient and Nusselt number in a circular duct with a 180$^{\circ}$ bend for Re=6 x 10$^4$, 8 x 10$^4$ and 1 x 10$\^$5/ under swirling flow and non-swirling flow conditions. The test tube with a circular section was made from stainless steel having a curvature ration of 9.4. Current heat flux of 5.11 kW/㎡ was applied to the test tube by electrical power and the swirling motion of air was produced by a tangential inlet to the pipe axis at 180$^{\circ}$. Measurements of local wall temperatures and the bulk mean temperatures of air were made at four circumferential positions at 16 stations. The wall temperatures showed a reduced distribution curve at the bend for the non-swirling flow, but this effect did not appear for the swirling flow. The Nusselt number distributions for the swirling flow, which was calculated from the measured wall and the bulk temperatures, were higher than that of the non-swirling flow. The average Nusselt number of the swirling flow increased by about 90-100%, compared to that of the non-swirling flow. The Nu/Nu$\_$DB/ values at the 90$^{\circ}$ station for non-swirling flow and swirling flow were approximately 2.5 and 4.8 at Re=6x10$^4$ respectively. The values agree well with Said's results for non-swirling flow.

• Journal of Sensor Science and Technology
• /
• v.13 no.5
• /
• pp.399-404
• /
• 2004

We report on the technology of formation of sandwich structures based on fullerite films and on experimental results in research of optical and conductivity properties of these sandwich samples. Single crystals of sapphire (100) or silicon were used as substrates. The sandwich specimens were based on the structure M/$C_{60}$/M (M=Cr, Pd, Ag, Al, Cu). The thickness of the fullerite films was about $0.2{\sim}1.0{\mu}m$. The area of the $C_{60}$ film under the top contact was about $1cm^{2}$. The specimens have been investigated by infrared spectroscopy, spectra-photometry, ellipsometry and X-ray diffraction analysis. Measurements of the current/voltage characteristics and research on the temperature dependence of conductivity were performed as well. It was shown that metals such as Cr, Pd, Ag, Al, and Cu penetrate easily into the fullerite films. It appears that these specimens have a large conductivity. For silver/$C_{60}$ and other sandwich structures the conductivities show a semiconductor-like behaviour.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.03a
• /
• pp.219-219
• /
• 2003

HVOF(High Velocity Oxygen Fuel)법을 사용한 MCrAlY(M=Ni, Co, Fe)계 열차폐 코팅(thermal barrier coating)은 열기관 내부의 극심한 환경 부하에 대해 구조물 표면에 열적, 화학적 장벽을 형성함으로써 구조물의 내구성을 향상시킨다 이와 동시에 열차폐 효과는 구조물의 온도상승 없이 내부 가동 온도를 높일 수 있게 함으로써 열효율을 상승시키고 연료 효율을 높여 가동비용 절감을 이룰 수 있는 동시에 고 연소를 통한 오염원의 배출을 감소시킬 수 있다. 본 연구에서는 $H_2O$$_2$=5:1 분위기 하에서 HVOF법을 사용하여 Hastelloy-X 기판위에 125$\mu\textrm{m}$의 두께로 다음 5종류의 (Ni, Co, Cr)계 MCrAlY 코팅을 용사시켰다. 준비된 (Ni, Co)-Cr-Al-(Y, Ta, Re), (Ni, Co)-Cr-Al-(Y, Re), (Ni, Co)-Cr-Al-(Y, Ta), (Ni, Co)-Cr-Al-Y, (Ni,Co)-Cr-Al-Ir 코팅시편에 대한 산화성질을 조사하기 위해 대기 중 1000, 1100, 120$0^{\circ}C$에서 50, 100, 150, 200시간 등온실험(Isothermal oxidation)을 실시하였고, XRD, SEM/EDS, EPMA를 이용하여 생성된 산화막과 코팅 시편의 조직 변화를 조사하였다. 산화온도와 산화시간이 증가할수록 산화막의 박리가 많이 발생하였으며, 분석 결과 미세하게 분포된 a-Al$_2$O$_3$ 입자, NiCr$_2$O$_4$스피넬 상, 미세한 Cr$_2$O$_3$가 관찰되었고, 코팅 조성 변화에 따라 형성되는 이들 산화물의 존재비가 달라졌으며, 산화온도가 높아질수록 산화속도가 가속화되었다.

• Environmental Engineering Research
• /
• v.25 no.1
• /
• pp.52-61
• /
• 2020

The article examines the impact differences between producing concrete and asphalt. Both materials are widely used in the construction industry. Construction activities account for a large portion of greenhouse gases. Therefore, it is important to consider the Life Cycle Analysis (LCA) to reduce environmental impacts. In this study, the material processes were inputted into an LCA program called SimaPro. The database used for the study was Ecoinvent as it is one of the major databases within SimaPro. The materials were compared against impacts per kg of material produced as the functional unit. Each process was created using the materials, energy and transportation required to produce the materials. Waste streams were also included in the process to determine the impacts after the product was done with its useful life. Using the ReCiPe method, an LCA was conducted. Midpoint and endpoint categories were examined for both the productions. The processes had similar results for the human health and ecosystems categories; however asphalt was marginally higher for both. Asphalt had exceeded concrete in the resource impact category by 100 mPt. The results indicate that concrete is the more sustainable building material. Determination of various impacts of the materials is important for material selection.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.7
• /
• pp.551-556
• /
• 2001

In this work, the recovery of etching damage in the etched PZT thin film with $O_2$ annealing has been studied. The PZT thin films were etched as a function of Cl$_2$/Ar and additive CF$_4$ into Cl$_2$(80%) /Ar(20%). the etch rates of PZT thin films were 1600$\AA$/min at Cl$_2$(80%)/Ar(20%) and 1970 $\AA$/min at 30% additive Cf$_4$ into Cl$_2$(80%)/Ar(20%). In order to recover the characteristics of etched PZT thin films, the etched PZT thin films were annealed in $O_2$ atmosphere at various temperatures. From the hysteresis curves, ferroelectrical properties are improved by $O_2$ annealing process. The improvement of ferroelectric behavior is consistent with the increase of the (100) and (200) PZT phase revealed by x-ray diffraction (XRD). From x-ray photoelectron spectroscopy (XPS) analysis, intensities of Pb-O, Zr-O and Ti-O peak increase and the chemical residue peak is reduced by $O_2$ annealing. From the atomic force microscopy (AFM) images. it shows that the surface morphology of re-annealed PZT thin films after etching is improved.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.4
• /
• pp.765-774
• /
• 1992

The effect of the interactive flow on convective heat transfer from two vertical isothermal parallel plates have been studied numerically by the finite difference method. The Reynolds number, Grashof number, the relative length, L$_{2}$/L$_{1}$, and the dimensionless plate spacing, b/L$_{1}$ are varied as parameters. In case of outside mean Nusselt number, left outside mean Nusselt numbers show same values as L$_{2}$/L$_{1}$ and b/L$_{1}$ increase, but right outside mean Nusselt numbers decrease as L$_{2}$/L$_{1}$ increases. The inside mean Nusselt numbers are constant at narrow spacings and increase at wide spacings as Grashof numbers increase. The optimun plate spacing on left inside mean Nusselt numbers is b/L$_{1}$=0.4 at Re=100 and b/L$_{1}$=0.3 at Re=200. For the right inside mean Nusselt number, the optimum plate spacings move to the narrow spacing as Reynolds numbers increase and L$_{2}$/L$_{1}$ decrease.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.23 no.11
• /
• pp.754-761
• /
• 2011

The present study numerically investigates two-dimensional flow and heat transfer in the multiple confined impinging slot jet. Numerical simulations are performed for the different Reynolds numbers(Re=100 and 200) in the range of nozzles from 1 to 9 and height ratios(H/D) from 2 to 5, where H/D is the ratio of the channel height to the slot width. The vector plots of velocity profile, stagnation and averaged Nusselt number distributions are presented in this paper. The dependency of thermal fields on the Reynolds number, nozzle number and height ratio can be clarified by observing the Nusselt number as heat transfer characteristic at the stagnation point and impingement surface. The Nusselt number at the stagnation point of the central slot shows unsteadiness at H/D=3 and Re=200. The value of Nusselt number at the stagnation point of the central slot decreases with higher Reynolds number and number of nozzle although overall area averaged Nusselt number increases. Hence careful selection of geometrical parameters and number of nozzle are necessary for optimization of the heat transfer performance of multiple slot impinging jet.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.30 no.5 s.248
• /
• pp.438-445
• /
• 2006

We performed the simulation of the unsteady three dimensional flow over a square cylinder in a wind tunnel in moderate Reynolds number range, $100{\sim}2500$ by using LBM. SGS model was applied for the turbulent flow. Frist of all we compared LBM(Lattice Boltzmann Method) solution of Poiseuille flow applied Farout and bounce back boundary conditions with the analytical and FOAM solutions to verify the applicability of the boundary conditions. For LBM simulation the calculation domain was formed by structured grids and prescribed uniform velocity and density inlet and Farout boundary conditions were imposed on the in-out boundaries. Bounceback and wind tunnel boundary conditions were applied to the cylinder walls and the boundaries of calculation domain respectively. The maximum Strouhal number of the vortex shedding is 0.2025 at Re = 750. and the number maintains the constant value of 0.18 when Re>1000. We also predicted that the critical reynolds number of the turbulent flow is in the range of $250{\sim}500$.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.11a
• /
• pp.30.1-30.1
• /
• 2009

정보화가 급속히 진전됨에 따라 보다 많은 양의 정보를 전송, 처리, 저장하게 되면서 이를 위해 대용량, 고속, 비휘발성의 특징을 갖는 차세대 메모리의 개발이 절실히 요구되고있다. 이 중 저항 변화 메모리(ReRAM)는 일반적으로 TiO2, Al2O3, NiO2, HfO2, ZrO2 등의 전이금속산화물을 이용한 MIM 구조로서 적당한 전기 신호를 가하면 저항이 높아서 전도되지 않는 상태(Offstate)에서 저항이 낮아져 전도가 가능한 상태(On state)로 바뀌는 메모리 특성을가진다. ReRAM은 비휘발성 메모리이며 종래의 비휘발성 기억소자인 Flash memory 보다 access time 이105 배 이상 빠르고, 5V 이하의 낮은 전압에서도 동작이 가능하다. 또한 구조가 간단하여 공정 단순화가 가능하고 소자의 집적화도 쉽다는 점 등 많은 장점들이 있어서 Flash memory를 대체할 수 있는 유력한 후보로 여겨지고 있다. 본연구에서는 DC-magnetron Sputtering 방법으로 전이금속 박막을 증착하고, Dry furnace로 산화시켜 전이금속산화물 박막을 제작한 후 저항변화 특성을 연구하였다. 두 개의 전이금속산화물 박막을 dual-layer로 형성시켜 저항변화특성을 관찰하였으며 또한, 전이금속산화물 박막의 조성을 달리 하여 저항변화를 관찰 하였다. 전이금속산화물 박막의 전기적 특성을 알아보기 위해 Si(100) wafer 위에 Pt를 이용 MIM 형태로 capacitor 시편을 제작 하여, probe station으로 I-V 측정을 하였고 조성 및 표면 분석을 위해서는 AES와 AFM을, 미세구조를 분석을 위해서는 TEM과 SEM 을 사용하였다.

• YAKHAK HOEJI
• /
• v.42 no.3
• /
• pp.296-301
• /
• 1998

To investigate the effects of ginsenosides from Panax ginseng on mitogenic responses in macrophages and splenocytes from murine, we examined the effects of representative protopanaxadiol and protopanaxatriol ginsenosides ($Rb_1,\;Rb_2,\;Re\;and\;Rg_1$) on tumor necrosis factor-${\alpha}$ (TNF-(${\alpha}$) production in murine macrophage cell line (RAW264.7 cells) stimulated by lipopolysaccharide (LPS) and T cell proliferation in splenocytes stimulated by concanavalin A (Con A). Among the ginsenosides tested, protopanaxadiol ginsenosides ($Rb_1\;and\;Rb_2$) significantly inhibited TNF-${\alpha}$ production in a dose-dependent manner. However, protoppanaxatriol ginsenosides (Re and $Rg_1$) showed little inhibitory activity. The molar concentrations of $Rb_1\;and\;Rb_2$ producing 50% inhibition ($IC_{50}$) of TNF-${\alpha}$ production were $55.8{\mu}g/ml\;(48.0{\mu}M)\;and\;31.8{\mu}g/ml (27.9{\mu}M)$, respectively. As a positive control, prednisolone also exhibited inhibitory activity with an $IC_{50}$ value of $21.7{\mu}M$. In T cell proliferation, $Rg_1$, was not effective but $Rb_1$ and Re or $Rb_2$ significantly increased or inhibited at high concentration, 75 and $100{\mu}g/ml$. In contrast, prednisolone showed potent inhibitory activity with an $IC_{50}$ value of 6.1nM. These results suggest that ginsenosides may take part in the mitogen-induced signaling pathway for TNF-${\alpha}$ production and T cell proliferation from macrophages and splenocytes.