• Transactions on Electrical and Electronic Materials
• /
• v.9 no.3
• /
• pp.91-95
• /
• 2008

In this study, in order to develop the composition ceramics for low loss multilayer piezoelectric actuator application, $Pb(Zn_{1/2}W_{1/2})O_3-Pb(Mn_{1/3}Nb_{2/3})O_3-Pb(Zr,Ti)O_3$ (abbreviated as PZW-PMN-PZT)ceramics according to the amount of $MnO_2$ addition were fabricated using two-stage calcinations method. And also, their dielectric and piezoelectric properties were investigated. At the 0.2 wt% $MnO_2$ added PZW-PMN-PZT ceramics sintered at $930^{\circ}C$, density, electromechanical coupling factor $k_p$, dielectric constant ${\varepsilon}_r$, piezoelectric $d_{33}$ constant and mechanical quality factor $Q_m$ showed the optimum value of $7.84g/cm^3$, 0.543, 1,392, 318.7 pC/N, 1,536, respectively for low loss multilayer ceramics actuator application.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.11
• /
• pp.23-30
• /
• 1998

The use of microstrip is very common for various passive microwave devices because of the rather simple and planar structure. However, many microstrip devices require fairly large surface areas, which results in real estate problems of finite substrates. In this paper, we proposed a perforated microstrip with longitudinal slow-wave effect and characterized experimentally and theoretically. The impedance matching to the reference impedance(50 $\Omega$) and the quality factor are greatly improved compared to the conventional slow-wave structure with modulated strip. Because of the structural simplicity, it can be easily applied to miniaturize many microstrip devices.

• Proceedings of the IEEK Conference
• /
• 2004.06a
• /
• pp.213-216
• /
• 2004

This paper describes design and implementation of the 5.5 GHz VCO with parallel-branch inductors using 0.8${\mu}m$ SiGe HBT process technology. The proposed parallel-branch inductor shows $12 \%$ improvement in quality factor in comparison with the conventional inductor. A phase noise of -93 dBc/Hz is measured at 100 kHz offset frequency, and the harmonics in the VCO are suppressed less than -23 dBc. The single-sided output power of the VCO is -6.5$\pm$1.5 dBm. The manufactured VCO consumes 15.0 mA with 2.5 V supply voltage. Its chip areas are 1.8mm ${\times}$ 1.2mm.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1996.11a
• /
• pp.291-294
• /
• 1996

We present the experimental results of high quality factor (Q) inductors fabricated on high-resistivity silicon wafer using standard CMOS process without any modificatons such as thick gold layer or multilayer interconnection. This demonstrates the possibility of building high Q inductors using lower cost technologies, compared with previous results using complicated process. The comparative analysis is carried out to find the optimized inductor shape for the maximum performance by varying the thickness of metal and number of turns with rectangular shape.

• Electrical & Electronic Materials
• /
• v.9 no.9
• /
• pp.900-905
• /
• 1996

We have investigated dielectric properties of low fired ceramics BiNbO$_{4}$ containing 0.05[wt%] V$_{2}$O$_{5}$ and x[wt%l Cr$_{2}$O$_{3}$ (x=0, 0.2, 0.4, 0.8, 1.2). By substituting Cr for Bi, dielectric constant .epsilon.$_{r}$ and quality factor Q.f increased and temperature coefficient of resonant frecquency .tau.$_{f}$ changed to positive value. In the composition of BiNbO$_{4}$+0.05 [Wt%] V$_{2}$O$_{5}$+0.8[wt%]Cr$_{2}$O$_{3}$ sintered at 960[.deg. C], we could obtain microwave dielectric properties of .epsilon.$_{r}$=49, Q.f.simeq.3000[GHz](at 4.8[GHz]), .tau.$_{f}$.simeq.0[ppm/.deg. C]. As the above ceramics can be sintered near 960[.deg. C], it is applicable to multilayer microwave device with Ag conductor.tor.tor.tor.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.62 no.6
• /
• pp.762-766
• /
• 2013

Interest in Wireless Power Transmission (WPT) technology has been increasing worldwide recently. This trend is proved by commercialized products such as electric toothbrush, wireless razor, and wireless charger for mobile phone battery. Studies for enhancing the applicability of the technology have been continuously conducted. Currently the WPT technology is based on the technologies using microwave, inductively coupling, and magnetic resonance. In the meantime, development of the microwave-based WPT faces difficulty due to health hazards involved in the technology, and application of the WPT technology using inductively coupling is restricted by area due to the problem of transmission length. In comparison, the WPT technology using magnetic resonance draws attention in terms of efficiency and transmission length. In this study, the sending coil based on the WPT technology using magnetic resonance system was replaced with an HTS coil to enhance transmission efficiency. Since the HTS coil has a zero resistance, power transmission loss can be minimized. At the same time, size of the current density could be increased to 100 times or more than typical coils. In addition, through impedance matching of LC device, maximal resonance properties were induced and consequently, frequency selection quality characteristics or Q was enhanced. As a result, the WPT type using the HTS coil showed a longer transmission length and better transmission efficiency compared with the WPT type using typical coils.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.1
• /
• pp.60-67
• /
• 2002

In this paper, the dual band VCO of mobile communication terminal using oscillation part switching circuit is proposed. In order to model the VCO accurately, the resonator is converted the equivalent circuit which is analyzed to use numerical method and designed optimal the dual band VCO operating GSM and DCS band. In order to demonstrate the objective theory of the proposed VCO, the dual band VCO is designed and experimented. The results of experiment, it is conformed that the VCO can be used mobile communication hand phone and components of three generation mobile communication systems.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.5
• /
• pp.394-399
• /
• 1998

High power characteristics with vibration velocity were studied in $Pb(Y_{2/3}W_{1/3})O_3-Pb(Zr,Ti)O_3$(PYW-PZT) ceramics by using the constant current method. Young s modulus $Y_0^E$ and mechanical quality factor $Q_m$ are a function of the square of effective vibration velocity \upsilon_0$. The nonlinear proportional constants of the above functions indicate the degree of stability under the vibration level change. The stability of PYW-PZT ceramics estimated by these constants coincides with the results obtained through the heat generation. It was found that $Q_m$ was markedly decreased with increasing the vibration velocity, accompanying a lot of heat generation. The vibration hysteresis and dielectric loss according to the vibration velocity was reduced by doping $Fe_2O_3$to the ceramics. On the contrary, these losses was increased by doping $Nb_2O_5$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.11a
• /
• pp.279-282
• /
• 2003

For the millimeter-wave dielectrics, Forsterite-based ceramics were produced. Pure forsterite ceramics($Mg_2SiO_4$) shows porous micro-structure and very low Q*f values, which is not suitable for the dielectrics for the millimeter-wave band. Several sintering aids including $Al_2O_3$, $Li_2CO_3$, $Li_2SiO_4$, were added to the forsterite ceramics in order to produce dense low-loss dielectrics. Among these additives, $Li_2CO_3$ is the most effective sintering aids. Several sub-components including NiO, ZnO, $SnO_2$, $TiO_2$, were added to enhance the microwave dielectric properties. $TiO_2$ is the most effective additive to enhance the dielectric properties at microwave bands. The simultaneous addition of $TiO_2$ and $Li_2CO_3$ increases Q*f value over 170,000, which can be used as dielectrics in millimeter-wave bands.

• Journal of Astronomy and Space Sciences
• /
• v.24 no.4
• /
• pp.397-408
• /
• 2007

Diplexer is one of core devices needed to communicate with satellite using single ground antenna by separating uplink and downlink signal. This paper presents the design of the S-band diplexer for LEO TT&C application, especially for KOMPSAT (KOrea Multi-Purpose SATellite). To cope with requirements such as high handling power, low insertion loss, air-cavity resonator with high quality factor was considered as one of design drivers. Design was started with predicting unloaded Q and equivalent circuit from the structure of air-cavity resonator. For the convenience of adjustment, the coupling factor placed between resonators was estimated from COTSEM (Electro-Magnetic) simulator, EESOF $ADS^{TM}$, and expressed with 2-order polynomial regression. To improve the isolation between transmitting part (Tx) and receiving part (Rx), the inductive and capacitive attenuation poles were inserted between $4^{th}\;and\;6^{th}$ resonator respectively. The fabricated diplexer consists of two bandpass filters and each filter has eight resonants. From the measurement, it was shown that major requirements such as 0.5dB of insertion loss, 20dB of return loss and 100dB of isolation were fully satisfied within passband.