• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.49 no.4
• /
• pp.246-255
• /
• 2000

This paper deals with a novel full digital control method of the three-phase PWM inverter for UPS. The voltage and current of output filter capacitor as state variables are the feedback control input. In addition, a double deadbeat control consisting of a d-q current minor loop and a d-q voltage major loop, both with precise decoupling, have been developed. The switching pulse width modulation based on SVM is adopted so that the capacitor current should be exactly equal to its reference current. In order to compensate the calculation time delay, the predictive control is achieved by the current·voltage observer. The load prediction is used to compensate the load disturbance by disturbance observer with deadbeat response. The experimental results show that the proposed system offers an output voltage with THD less than 2% at a full nonlinear load.

• Proceedings of the KIEE Conference
• /
• 2003.07b
• /
• pp.738-740
• /
• 2003

A lot of R&D on the diagnosis of stator winding insulation for large rotating machines has been carried out since the 1970s. The on-line partial discharge measurement has proved to be an effective technique in the evaluation of the state of stator insulation in high voltage rotating machines. It is well known that if the discharge pulses propagate through the winding conductor, they are attenuated and delayed. In the present study, to investigate the attenuation and the time delay of discharge pulses through the winding conductor, a series of tests were conducted using a model coils and slot. Thus it could be concluded that while the high frequency pulse propagates in radiation or end-winding coupling modes, the low frequency one does in a series mode through the coil conductor.

• Proceedings of the KIPE Conference
• /
• 2001.07a
• /
• pp.163-166
• /
• 2001

In this paper, a two-level switching algorithm ov the deadbeat to control PWM inverter is proposed. A modified algorithm of the deadbeat is suitable for the UPS system. Two levels in the pulse pattern are used. This scheme allows the use of higher switching frequency for a given computation time delay, which results in lower total harmonic distortion at the output. The proposed control scheme is implemented using TMS320F240 DSP for controlling on inverter.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.25 no.2
• /
• pp.87-93
• /
• 2020

This study proposes a gate driver that operates semiconductor switches in the bipolar pulsed power modulator. The proposed gate driver was designed to receive isolated power and synchronized signals through the gate transformer. The gate circuit has a separate delay in the on-and-off operation to prevent a short circuit between the top and bottom switches of each leg. On the basis of the proposed gate circuit, a bipolar pulsed power modulator prototype with a 2.5 kV/100 A rating was developed. Finally, the bipolar pulsed power modulator was tested under resistive load and plasma reactor load conditions. It is verified that the proposed gate driver can be applied to a bipolar pulsed power modulator.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.05a
• /
• pp.153-156
• /
• 2005

In this study, we have investigated transient properties of top emission organic light emitting diode (OLED) with a red electrophosphorescent dopant. The emission spectrum shows a strong peak at 620 nm accompanied with a small peak at 675 nm in the red region. Time evolution of electrophosphorescence reveals a decay time of 703 ms at a voltage pulse of 5 V in a device with an emitting area of 20 $mm^2$. Rise and delay times vary from 450 to 14 ms and 73 to 3 ms, respectively, as the voltage amplitude increases from 4.5 to 10 V. These results are compared with the red emitting device without an electron injection layer.

• Journal of Power System Engineering
• /
• v.6 no.4
• /
• pp.81-87
• /
• 2002

The modelling and controller design of the EMV(electro-magnetic valve) for vehicle engine are considered in this paper. For the analysis and controller design, the governing equation of the EMV system is derived. For a good performance of the system, the start control, the holding control and the swing control are included in the controller design of the EMV system. In order to reduce landing speed of the valve, the on-time delay control which mainly come from the optimal control theory is employed. In order to reduce the power consumption of the system, the pick-up and hold operation has been used for the magnetic coil. The simulation and experimental results are presented to show the validity of the control method.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.284-284
• /
• 2013

중 에너지 이온 산란 분석법(Medium Energy Ion Scattering Spectrometer, MEIS)은 50~500 keV로 이온을 가속 후 시료에 입사시켜 시료의 원자와 핵간 충돌로 산란되는 일차이온의 에너지를 측정하여 시료를 분석하는 기법으로, 원자층의 깊이 분해능으로 초박막의 표면 계면의 조성과 구조를 분석 할수 있는 유용한 미세 분석기술이다. 본 실험에서 에너지 70~100 keV의 He+ 이온을 사용하여 Pulse Width 1 ns의 Pulsed ion beam을 만들어 Start 신호로 사용하고 Delay-line-detector에 검출된 신호를 End 신호를 이용한 TOF-MEIS System을 개발하였다. 활용 가능한 분석시편으로 Ultra thin film 시편으로 1, 1.5, 2, 2.5, 3, 4 nm의 HfO2, 1.8, 4nm의 SiO2 시편을 분석 하였으며 Ultra Shallow Junction 시편으로 As Doped Si, Cs Doped Si 시편 및 Composition, Core/shell 구조의 Q-dot 시편으로 CdSe, CdSe/ZnS등 다양한 분석 실험을 진행 하였다. Composition, Core/shell 구조의 Q-dot 시편은 Diamond Like Carbon(DLC)의 Substrate에 Mono-layer로 형성하여 분석하였다.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.11a
• /
• pp.720-725
• /
• 2000

A new ultrasonic pulse-echo technique was developed and described for vibration measurement of the suspension assembly in hard disk drives. The method is based upon the difference in magnitude of two consecutive reflection waves from a moving object(suspension), while the traditional ultrasonic vibrometer uses the phase shift of the reference wave and the reflection wave. A cone-shape delay line is designed to access the small structure. A simple mathematical model is presented and analyzed with experimental results to show the feasibility of the method. The advantages of this ultrasonic vibration measurement method are relatively high resolution, low cost, and ease of implementation comparing with the Laser Doppler vibrometer.

• Proceedings of the Optical Society of Korea Conference
• /
• 2003.07a
• /
• pp.248-249
• /
• 2003

The characterization of laser mirrors is important for obtaining proper performance of femtosecond lasers. Characteristics of laser mirrors are usually described in terms of their reflectivity at a certain wavelength. In femtosecond laser applications, however, the dispersion property of the mirror should be considered because the temporal shape of a femtosecond light pulse changes during the reflection at the mirrors. (omitted)

• Journal of the Optical Society of Korea
• /
• v.15 no.1
• /
• pp.103-108
• /
• 2011

Recently reported asynchronous-optical-sampling terahertz (THz) time-domain spectroscopy enables high-resolution spectroscopy due to a long time-delay window. However, a long-lasting tail signal following the main pulse is often measured in a time-domain waveform, resulting in spectral fluctuation above a background noise level on a high-resolution THz amplitude spectrum. Here, we adopt the wavelet power spectrum estimation technique (WPSET) to effectively remove the spectral fluctuation without sacrificing spectral features. Effectiveness of the WPSET is verified by investigating a transmission spectrum of water vapor.