• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2003년도 가을 학술발표회 논문집
• /
• pp.215-218
• /
• 2003

To analyze a bond stress-slip behavior between a reinforcing bar and concrete under repeated loading, pull-out fatigue test was performed. Major variables were repeated stress levels and cycle numbers. Test specimen was taken repeated constant amplitude loading before it was fractured by pull-out test. Increments of bond strength and slip according to repeated stress level and cycle numbers were analyzed. On the basis of test results, Local bond stress-slip relationship under repeated loading were formulated

• 마이크로전자및패키징학회지
• /
• 제25권4호
• /
• pp.111-118
• /
• 2018

강성도가 서로 다른 두 polydimethylsiloxane (PDMS) 탄성고분자와 flexible printed circuit board (FPCB)로 이루어진 soft PDMS/hard PDMS/FPCB 구조의 강성도 국부변환 신축기판을 개발하기 위해 PDMS와 FPCB를 acrylic-silicone 양면테이프를 사용하여 접합한 후 접합공정에 따른 PDMS/FPCB 계면접착력을 분석하였다. 완전 경화된 PDMS에 acrylic-silicone 양면테이프의 silicone 접착제로 접착한 FPCB의 pull 강도는 259 kPa이었으며, pull 시험시 PDMS와 silicone 접착제 사이에서 박리가 발생하였다. 반면에 $60^{\circ}C$에서 15~20분 유지하여 반경화시킨 PDMS에 acrylic-silicone 양면테이프의 silicone 접착제로 FPCB를 접착 후 $60^{\circ}C$에서 12시간 유지하여 PDMS를 완전 경화시키면 pull 강도가 1,007~1,094 kPa로 크게 향상되었으며, pull 시험시 계면 박리가 acrylic-silicone 양면테이프의 acrylic 접착제와 FPCB 사이에서 발생하였다.

• Computers and Concrete
• /
• 제26권6호
• /
• pp.587-593
• /
• 2020

In this study, bond behavior of ordinary concrete and rebars with different diameters and development length was investigated by using Hinged Beam Test (HBT) and Eccentric Pull-Out Test (EPT) comparatively. For this purpose, three different rebar size and development length depending on rebar diameter were chosen as variables. Three specimens were produced for each series of specimens and totally 54 specimens were tested. At the end of the tests it was observed that obtained results for both tests were quite similar. On the other hand, increased bar size, especially for the specimen with 14 mm bar size and 14 development length (lb), caused shear failure of test specimens. This situation infers that when bigger bar size and lb are used in such test, dimensions of test specimens should be chosen bigger and stirrups should be used for producing of test specimens to obtain more adequate result by preventing shear failure. Also, a nonlinear regression analysis was employed between HBT and EPT results. There was a high correlation between the EPT values, lb, rebar diameters and estimated theoretical HBT. In addition, at the end of the study an equation was suggested to estimate bond strength for HBT by using EPT results.

• International Journal of Concrete Structures and Materials
• /
• 제11권1호
• /
• pp.69-84
• /
• 2017

This paper presents results of an experimental investigation on the behaviour of bond between external glass fibre reinforced polymer reinforcement and concrete exposed to three different environmental conditions, namely, temperature cycles, wet-dry cycles and outdoor environment separately for extended durations. Single shear tests (pull-out test) were conducted to investigate bond strengths (pull-out strengths) of control (unexposed) and exposed specimens. Effect of the exposure conditions on the compressive strength of concrete were also investigated separately to understand the effect of changing concrete compressive strength on the pull-out strength. Based on the comparison of experimental results of exposed specimens to control specimens in terms of bond strengths, failure modes and strain profiles, the most significant degradation of pull-out strength was observed in specimens exposed to outdoor environment, whereas temperature cycles did not cause any deterioration of strength.

• 한국정보시스템학회지:정보시스템연구
• /
• 제30권4호
• /
• pp.71-94
• /
• 2021

Purpose The purpose of this study is to verify impacts of factors, representing Push-Pull-Mooring(PPM) on switch intention to OTT(Over-The-Top) service in demand for content and to find relationship between factors through empirical analysis. Design/methodology/approach This study designed a research model by deriving factors affecting the intention to switch on OTT service based on the Push-Pull-Mooring framework and researches on OTT service. To test the hypothesis, a total of 357 responses were collected from individuals with experience in using OTT service and analyzed using SPSS26 and SmartPLS3.0. Findings According to the empirical analysis result, this study confirmed that the push, pull, and mooring factors proposed in this study had a significant effect on switching intention on OTT service. In addition, this study confirmed that both low switching cost and need for variety had a significant effect except for hypothesis H8.

• Corrosion Science and Technology
• /
• 제13권5호
• /
• pp.186-194
• /
• 2014

Establishment of adhesion strength measurement procedure for marine epoxy coatings was conducted in order to ensure reliability of the test results. It was found that (1) the increase in thickness of the substrates would induce increase of pull-off strength. Especially, the increase in adhesion strength with the substrate thickness increment was attributed to the transition of stress mode to the pure tensile mode excluding bending effect. (2) The longer curing time, the higher pull-off strength. It may be due to higher cross-linking density of the coating (3) The pull-off strength increases as coating thickness increases due to the diminishment of bending effect (4) The longer drying time after water immersion, the higher pull-off strength. It may be due to the evaporation of water molecule at the coating-substrate interface.

• 한국지반공학회논문집
• /
• 제21권10호
• /
• pp.123-131
• /
• 2005

본 연구에서는 양압력을 받는 기초구조물의 보강공법으로 앵커를 시공할 경우, 이에 대한 파괴메카니즘 및 안정해석법의 개발에 기초적인 자료를 제공하기 위해 나선형 앵커에 대한 실내인발시험 및 유한요소해석을 수행하였다. 실내인발시험은 강우시 지하수위 상승으로 인해 기초구조물에 양압력이 작용하는 경우를 고려하기 위해 포화사질토 내에서의 하중-변위특성을 분석한 후, 이를 건조시의 경우 등에 대해 유한요소 해석결과와 비교${\cdot}$분석하였으며, 앵커의 극한인발저항력에 미치는 영향인자 및 앵커의 인발에 따른 거동특성 등을 평가하였다. 또한, 군형태 앵커의 설치간격을 변화시켜가면서 하중-인발변위 특성을 비교한 후, 나선형 앵커의 무리효과에 의한 간섭영향 요인을 분석하였다.

• 한국산학기술학회논문지
• /
• 제13권6호
• /
• pp.2797-2803
• /
• 2012

본 논문은 모르타르에 근입되어 인발하중을 받는 정착판 GFRP 근의 인발거동을 기술하고 있다. 정착판 GFRP 근의 모르타르 시험체를 5개 제작하여 인발시험을 수행하였다. 시험 결과를 검증하기 위해 ANSYS 상용프로그램을 이용한 유한요소해석을 수행하였으며 시험결과와 비교되었다. 시험결과 모르타르에 매입된 정착판 GFRP 근의 파열 파괴강도식은 45도 콘(Cone)파괴 이론 보다는 CCD(Concrete Capacity Design)파괴이론을 적용하는 것이 타당한 것으로 나타났다.

• 한국농공학회논문집
• /
• 제63권3호
• /
• pp.27-33
• /
• 2021

Reclaimed land was mainly used as agricultural land for rice production. As a higher value-added business in the agriculture has recently been activated, green houses are being constructed. In case of green house construction on the reclaimed land, it is generally soft ground with high soil water content, so it is important to design the foundation for greenhouse construction. The object of this study, a pull-out test was conducted to derive the base line data of the wooden pile foundation when constructing a green house. To reproduce the actual site, 30% of soil saturation and 70% of soil saturation were created in the soil box. Groove number and depth were set as design factors of the wooden pile, and a pull-out test was conducted. As a result of the test, pull resistance increased as the number of grooves increased, pull-out resistance according to groove depth was different according to soil saturation. Also, after the experiment, we want to compare the set-up effects over time.

• 한국도로학회논문집
• /
• 제19권2호
• /
• pp.25-34
• /
• 2017

PURPOSES: The purpose of this paper is to evaluate interface performance while using various tack coat materials for asphalt overlay. METHODS : The evaluation was conducted with tracking test, permeability, and interface bond strength. Tracking test was conducted using an image processing technique, to investigate the susceptibility of the tack coat materials. BBS and pull-off test were conducted to evaluate bond strength. The permeability test was conducted to evaluate the effect of tack coat materials. RESULTS : Results reveal that the trackless tack coat material demonstrates less tracking compared to other materials. Moreover, both BBS and pull-off tests can effectively evaluate the bond strength at the interface. RSC-4 was measured less bond strength. Moreover, tack coat prevents water penetration through the surface and aids the extension of the surface life of asphalt pavement. CONCLUSIONS : Trackless tack coat demonstrated a high and consistent bond strength performance. The tack coat types demonstrate marginally different performance as function of curing times. Field applicability was tested based on visual observation. Therefore, these should be considered when trackless tack coat is slightly enhanced the pavement performance based on limited this study results. Finally, it is necessary to allow reasonable time for the tack coat to completely cure.