• Membrane Journal
• /
• v.20 no.4
• /
• pp.342-350
• /
• 2010

Membrane distillation (MD) is a separation process which higher vapor pressure components are evaporated in mixed liquid solution through hydrophobic membrane with 0.1 or $0.5{\mu}m$ pore size. In this study, direct contact membrane distillation process for hollow fiber module were interpreted numerically using the "COMSOL Multiphysics" software. The variables for the system were temperatures and flow rates of lumen and shell side solutions. The permeate flux increased from 1.0 to $3.8L/m^2{\cdot}hr$ as temperature of the feed solution for lumen increased from 30 to $50^{\circ}C$. However the effect of shell solution temperature on permeate flux was relatively low. Also, the optimum velocity of lumen feed was obtained at 0.15 m/s ($Re_L=135$) by considering MD permeate flux as well as operating pressure loss.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.5
• /
• pp.1217-1230
• /
• 2010

The dynamic programming based methods, a kind of globally optimizing stereo matching methods, has the inherent advantage that the occlusion regions can be found during the process. But it also has a serious drawback of streaking phenomena. This paper focuses on reducing the streaking phenomena by adjusting the penalties in calculating the cost matrix and re-establishing the optimal path in the back-tracing process using the boundary information of the image. Especially we use a pixel expansion method in re-establishing the path, which is the results from expanding the pixel information of the ones just left the boundaries. Experiments with the four image pairs provided by the Middlebury site showed the results that the proposed method has the disparity error ratio of 6.33% and the rank is 29, which is competitive to the best method among the previously published dynamic programming based methods.

• Journal of the Korean Society of Systems Engineering
• /
• v.15 no.1
• /
• pp.1-8
• /
• 2019

Reverse engineering involves examining a system or component so as to comprehend its structure, functionality, and operation. Creation of a system model in reverse engineering can serve several purposes: test generation, change impact analysis, and the creation of a new or modified system. When attempting to reverse engineering a system, often the most readily accessible information is the system description, which does not readily lend itself to use in Model Based System Engineering (MBSE). Therefore, it is necessary to be able to transform this description into a diagram, which clearly depicts the behavior of the system as well as the interaction between components. This study demonstrates how sequence diagrams can be extracted from the systems description. Using MBSE software, the sequence diagrams for the Engineered Safety Features Component Control System (ESF-CCS) of the Nuclear Power Plant are created. Sequence diagrams are chosen because they are a means of representing the systems behavior and the interaction between components. In addition, from these diagrams, the system's functional requirements can be elicited. These diagrams then serve as the baseline of the reverse engineering process and multiple system views are subsequently be created from them, thus speeding up the development process. In addition, the use of MBSE ensures that any additional information obtained from auxiliary sources can then be input into the system model, ensuring data consistency.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.17 no.1
• /
• pp.120-129
• /
• 2009

Remanufacturing is an industrial manufacturing process. The merits of remanufacturing are to reuse old products to perform like a new product and to save energy, natural resources, landfill space and to reduce air pollution by less re-smelting. This paper proposes a systemic approach for activating the domestic remanufacturing industry. The approach is based on inside and outside regulations to apply remanufacturing companies. And, we analyzed the state and problems of remanufacturing industry for automobile parts. Also 5 essential tactics and 20 detail strategies are suggested. On the basis of the approach, the domestic remanufacturing industry will carry out the cooperation for their competitions.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.8
• /
• pp.839-847
• /
• 2012

Numerical simulations for channel flows with $Re_{\tau}$ = 180, 395 and 590 have been performed to investigate the hairpin packet formation process in wall-bounded turbulent flows. Using direct numerical simulation databases, the initial flow fields are given by the conditionally averaged flow field with the second quadrant event specified at the buffer layer. By tracking the initial vortex development, the change in the initial vortex to an ${\Omega}$-shaped vortex and th generation of a secondary hairpin vortex were found to occur with time scales based on the wall units. In addition, at the time when the initial vortex has grown to the channel center, the inclination angle of the hairpin vortex packet is approximately $12{\sim}14^{\circ}$, which is similar for all three Reynolds numbers. Finally, numerical simulations of the evolution of two adjacent hairpin vortices have been performed to examine the interaction between the adjacent vortex packets.

• Journal of the Korean Society of Costume
• /
• v.60 no.9
• /
• pp.95-105
• /
• 2010

The purpose of this study is in allowing thinking about the design development process which is more towards the visual and perceptional aspects related to the form structure by more diverse methods by typology of idea generation. To accomplish such goal, researches in the psychology, pedagogy, engineering, and consilient studies as well as related precedent researches and reference data in architecture, promotion, industrial design, and other art fields and fashion designs are collected and analyzed to see the study trend. In addition, in the content analysis method based on such, the idea generation was classified into types in consideration of relevancy, usefulness, and suitability with fashion. First, a concentrated thinking of a limited space is a method of leading an optimal design by focusing on solving the cause of a problem within a space which generates the problem. Second, plan thinking per section of structure decomposition is a method of dismantling the design problems per organization, thinking type, factor, and characteristic into sub-modules to re-interpret and re-organize the problems in various aspects. Third, an associated thinking through interpreting relationships among vocabularies is a method of selecting the marginal languages that allow a person to come up with concrete forms and the key words related to fashion to import the characteristics and attributes of the marginal languages and thematic relationship between the two terms to search the relevancy. Lastly, the free integrated thinking of language extension is a method of groping integration between other fields and fashion by free integration among the extended terms by extending the vocabularies through inferring metaphorical expressions founded upon individual's memories or knowledge concepts regarding theme words that do not allow concrete forms to come up.

• International Journal of Computer Science & Network Security
• /
• v.23 no.5
• /
• pp.172-178
• /
• 2023

In this paper, performance of autoencoder based OFDM communication systems is compared with IEEE 802.11a Wireless Lan System (Wi-Fi). The proposed autoencoder based OFDM system is composed of the following steps. First, one sub-carrier's transmitter - channel - receiver system is created by autoencoder. Then learning process of the one sub-carrier autoencoder generates constellation map. Secondly, using the plural sub-carrier autoencoder systems, parallel bundle is configured with inserting IFFT and FFT before and after the channel to configure OFDM system. Finally, the receiver part of the OFDM communication system was updated by re-learning process for adapting channel condition such as multipath channel. For performance comparison, IEEE802.11a and the proposed autoencoder based OFDM system are compared. For channel estimation, Wi-Fi uses initial long preamble to measure channel condition. but Autoencoder needs re-learning process to create an equalizer which compensate a distortion caused by the transmission channel. Therefore, this autoencoder based system has basic advantage to the Wi-Fi system. For the comparison of the system, additive random noise and 2-wave and 4-wave multipaths are assumed in the transmission path with no inter-symbol interference. A simulation was performed to compare the conventional type and the autoencoder. As a result of the simulation, the autoencoder properly generated automatic constellations with QPSK, 16QAM, and 64QAM. In the previous simulation, the received data was relearned, thus the performance was poor, but the performance improved by making the initial value of reception a random number. A function equivalent to an equalizer for multipath channels has been realized in OFDM systems. As a future task, there is not include error correction at this time, we plan to make further improvements by incorporating error correction in the future.

• International Journal of Computer Science & Network Security
• /
• v.24 no.3
• /
• pp.135-141
• /
• 2024

The article examines the key constants of reengineering the modern educational cluster, associated with the processes of digital transformation of all spheres of modern socio-cultural space. The first constant is the strategic rethinking of the educational process organization and awareness of the new roles of all participants (tutors, applicants, controlling elements, etc.). The other constant involves practical re-design of the system of educational services, which consists in the reorientation from the traditional model of education functioning for society to the implementation of the educational format in the form of new projects (structural, target, business). Consequently, the purpose of the study is to highlight the attitudes relevant to the modern realities of information and technological support of education in the context of socio-economic interactions of society. The criteria for the reengineering of educational concepts and the structural organization of the educational sphere are defined. The modern world is going through a period of complete digital transformation of all spheres of public activity. The scientific intelligence notes that education is no exception in these processes, as the dependence of educational realities on information and computer technologies is now noted. The COVID-19 pandemic, for all its tragedy, was also a kind of trigger, clearly marking the new components that have become defined in the organization of the educational process. The conclusion is made that the use of digital technologies in the organization of the educational institution or in the organization of the educational process has become not an auxiliary element, but a dominant factor. Mobility, dynamism, interdisciplinarity, synergy - all these aspects are relevant for socio-economic interactions of society and should be provided by educational programs. The results of the study can be used in the reorganization processes of educational institutions and institutions. Further research requires aspects of the analysis of the foreign experience of reengineering in education, carried out taking into account digital transformations of modern sociocultural space.

• The KIPS Transactions:PartD
• /
• v.12D no.7 s.103
• /
• pp.947-956
• /
• 2005

Software(S/W) reengineering is one of the effective technologies to produce a business worth and en and the S/W ROI continuously. In spite of, S/W reengineering has been recognized a cost-consumptive works with inefficient productivity. In fact we have used to transform to confusion system with destructive system architecture by extending and updating legacy system in a temporary expedients. Moreover it is impossible to provide the time-market products for coping with rapid changeable system environment and meeting to complicated customer's requirements. Therefore, we need a systematic reengineering methodology to fulfill the changeable environment, as appearance of new IT techniques, various alteration of business information model, and increment of business logic. Legacy systems can be utilized as the core property in business organization through reengineering methodology. In this paper, we target to establish the reengineering process, proposed MaRMI-RE consisting of initial Planning phase, reverse engineering and component transformation phase. To describe the MaRMI-RE, we presented the concrete tasks and techniques and artifacts per individual phase in process, and the case study is showed briefly.

• Journal of the Korean Society of Industry Convergence
• /
• v.25 no.6_2
• /
• pp.1119-1125
• /
• 2022

The depletion of resources and waste disposal caused by the continuous development of industry have emphasized the need to reduce consumption and production, recycle and reuse, and the importance of remanufacturing has increased in recent years. The spindle part of the aging planner miller, which is currently being remanufactured, is one of the factors that has the greatest impact on the performance of the machine tool. When designing the spindle part of the spindle shaft, there are considerations such as the configuration size bearing performance of the main shaft, but the diameter of the main shaft, the dangerous speed bearing, and the arrangement that affect the machining accuracy should be basically considered. As such, various studies have been conducted on the design of machine tool spindle spindles, but research on the reverse engineering of existing aging machine tool spindle spindles is poor. Reverse engineering is designing in the direction of improving performance by extracting specifications from already finished products, and first scanning the reverse engineered object through a 3D scanner, 3D modeling is performed based on the collected data, and then the process of deriving improvement plans by reverberating to improve performance by identifying wear and damage conditions is followed. Therefore, in this study, the purpose of this study is to provide data on reverse engineering by deriving improvement plans through optimal design for the bearing position of the aging planar Miller spindle spindle using central composite programming.