• Journal of the Optical Society of Korea
• /
• v.15 no.4
• /
• pp.362-367
• /
• 2011

Organic ($Alq_3$) film, which was coated on a donor plate, was transferred to an organic light emitting diode (OLED) substrate with help of heat generated by a dithering laser beam. The laser beam was diffracted in an acousto-optic modulator (AOM), then focused on the laser-to-heat converting layer of the donor plate; the focused spot followed trajectories guided by rotation of a Galvano-mirror. Three different functional waveforms, sine wave, square wave, and saw tooth wave were applied to the AOM as modulation signal to generate the dithering beam. The fluorescence microscope images of the donor plate showed that the patterns of removed $Alq_3$ film were affected considerably by the modulation waveforms and the phase difference between adjacent dithering beams. Further, the printed images of Alq3 film on the OLED substrate were different from the patterns of removed Alq3 film. Atomic force microscope images indicated that not only direct transfer but also deposition by sublimated vapor of Alq3 contributed to the pattern formation. Printed patterns affected considerably the electricity-to-light conversion characteristics of OLEDs. For uniform transfer, not only the phase relation of dithering beam lines but also adequate waveform were important.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.1638-1641
• /
• 2008

We have investigated the effectiveness of a gravure printing method for the fabrication of organic light-emitting diode (OLED) and Organic Thin Film Transistor (OTFT). Printing of the organic layers was performed with a small-scale gravure coating machine, while the metallic layers were vacuum-evaporated. Devices with gravure-printed layers are at least comparable with the spin-coated devices. Effects of the solvent formulation and surface energy mismatch between the organic layer materials on the printed patterns and device performance were discussed. We will present the initial design and experimental data of OTFT fabricated by roll-type soft contact transfer process.

• Journal of the Korean Society for Precision Engineering
• /
• v.28 no.10
• /
• pp.1153-1158
• /
• 2011

Roll-to-roll process is an emerging mass production method for printed and flexible electronics such as touch screen panel, RFID tag, thin film solar cell, and flexible display due to its high throughput. High precision in printing and coating is required to apply functional materials onto substrate. For such reason, every part of the roll-to-roll equipment needs to be precisely fabricated and to retain its precision under regular operation. In this article, the precision of cantilever type idler roller and a novel method to mitigate its deflection under web tension loading are discussed and the method is verified using both the numerical and the experimental works. The proposed method improves the structural rigidity of cantilever type roller whose advantages, such as low capital cost and high web path configurability, are maintained.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.1511-1514
• /
• 2009

Organic light emitting layer in OLED device was formed by gravure printing process in this work. Organic surface coated by gravure printing typically showed relatively bad uniformity. Thickness and roughness control was characterized by applying various mixed solvents in this work. Poly (N-vinyl carbazole) (PVK) and fact-tris(2-phenylpyridine)iridium($Ir(ppy)_3$) are host dopant system materials. PVK was used as a host and Ir(ppy)3 as green-emitting dopant. To luminance efficiency of the plasma treatment on etched ITO glass and then PEDOT:PSS spin coated. The device layer structure of OLED devices is as follow Glass/ITO/PEDOT:PSS/PVK+Ir(ppy)3-Active layer /LiF/Al. It was printed by gravure printing technology for polymer light emitting diode (PLED). To control the thickness multi-printing technique was applied. As the number of the printing was increased the thickness enhancement was increased. To control the roughness of organic layer film, thermal annealing process was applied. The annealing temperature was varied from room temperature, $40^{\circ}C$, $80^{\circ}C$, to $120^{\circ}C$.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.312-312
• /
• 2013

GaN based light emitting diodes (LEDs) are important devices that are being used extensively in our daily life. For example, these devices are used in traffic light lamps, outdoor full-color displays and backlight of liquid crystal display panels. To realize high-brightness GaN based LEDs for solid-state lighting applications, the development of p-type ohmic electrodes that have low contact resistivity, high optical transmittance and high refractive index is essential. To this effect, indiumtin oxide (ITO) have been investigated for LEDs. Among the transparent electrodes for LEDs, ITO has been one of the promising electrodes on p-GaN layers owing to its excellent properties in optical, electrical conductivity, substrate adhesion, hardness, and chemical inertness. Sputtering and e-beam evaporation techniques are the most commonly used deposition methods. Commonly, ITO films on p-GaN by sputtering have better transmittance and resistivity than ITO films on p-GaN by e-bam evaporation. However, ITO films on p-GaN by sputtering have higher specific contact resistance, it has been demonstrated that this is due to possible plasma damage on the p-GaN in the sputtering process. In this paper, we have investigated the advanced sputtering using plasma damage-free p-electrode. Prepared the ITO films on the GaN based LEDs by e-beam evaporation, normal sputtering and advanced sputtering. The ITO films on GaN based LEDs by sputtering showed better transmittance and sheets resistance than ITO films on the GaN based LEDs by e-beam evaporation. Finally, fabricated of GaN based LEDs by using advanced sputtering. And compared the electrical properties (measurement by using C-TLM) and structural properties (HR-TEM and FE-SEM) of ITO films on GaN based LEDs produced by e-beam evaporation, normal sputtering and advanced sputtering. As a result, It is expected to form plasma damage free-electrode, and better light output power and break down voltage than LEDs by e-beam evaporation and normal sputter.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.12 no.5
• /
• pp.879-886
• /
• 2008

This paper addresses the analysis and the design optimization of differential interconnects for Low-Voltage Differential Signaling (LVDS) applications. Thanks to the differential transmission and the low voltage swing, LVDS offers high data rates and improved noise immunity with significantly reduced power consumption in data communications, high-resolution display, and flat panel display. We present an improved model and new equations to reduce impedance mismatch and signal degradation in cascaded interconnects using optimization of interconnect design parameters such as trace width, trace height and trace space in differential flexible printed circuit board (FPCB) transmission lines. We have carried out frequency-domain full-wave electromagnetic simulations, time-domain transient simulations, and S-parameter simulations to evaluate the high-frequency characteristics of the differential FPCB interconnects. The 10% change in trace width produced change of approximately 6% and 5.6% in differential impedance for trace thickness of $17.5{\mu}m$ and $35{\mu}m$, respectively. The change in the trace space showed a little change. We believe that the proposed approach is very helpful to optimize high-speed differential FPCB interconnects for LVDS applications.

• Archives of design research
• /
• v.12 no.3
• /
• pp.191-200
• /
• 1999

The purpose of this study is to analyze traditional stereo images (stereopsis), and study electronic methods to create stereo images using computer graphics technology on visualization of computer. Computer system can process image data and show results on its display. In the early days of computer era, most scientific research data was printed on paper as a procession of digits. These days, the visualization of computer graphics has a precise and realistic quality in its imaging technology. Some technological advances have been developed to not only display 2-dimensional geometry but also 3-dimensional stereo images to simulate virtual reality. In this study, [ have discussed the history of stereopsis, principles of stereo images and technological developments. Also I analyzed the components of stereo images, optical and electronic methods and visual systems which are used in computer graphics technology. I developed my own theories on possibilities for new methods of 3-dimensional stereo images.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08b
• /
• pp.1257-1260
• /
• 2007

A single-wall carbon nanotube (SWNT) transparent conductive film (TCF) was fabricated using a simple inkjet printing method. The TCF could be selectively patterned by controlling the dot size to diameters as small as $34\;{\mu}m$. In this repeatable and scalable process, we achieved 71% film transmittance and a resistance of 900 ohm/sq sheet with an excellent uniformity, about ${\pm}\;5%$ deviation overall. Inkjet printing of SWNT is substrate friendly and the TCF is printed on a flexible substrate. This method of fabrication using direct printing permits mass production of TCF in a large area process, reducing processing steps and yielding low-cost TCF fabrications on a designated area using simple printing.

• Journal of the Semiconductor & Display Technology
• /
• v.12 no.1
• /
• pp.23-28
• /
• 2013

Epoxy resins are widely used in microelectronics packaging such as printed circuit board and encapsulating for semiconductor manufacturing. Water can diffuse into and through the epoxy matrix systems and moisture absorption at boarding interfaces of matrix resin systems can lead to a hydrolysis at the interfaces resulting in delamination of encapsulating materials. In the study, the changes of diffusion coefficient and moisture content ratio of epoxy resin systems with nano-sized fillers according to the change of liquid type epoxy resins were investigated. RE-304S, RE-310S, RE-810NM and HP-4032D as a epoxy resin, Kayahard AA as a hardener, and 1B2MI as a catalyst were used in these epoxy resin systems. After curing, moisture content ratios were measured with time under the 85 and 85% relative humidity condition using a thermo-hydrostat. The maximum moisture absorption ratio and diffusion coefficient of EMC decrease with the filler content. It can be seen that these decreases are due to the increase of filler surface area and the decrease of moisture through channel with the content of nano-sized filler.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2003.07a
• /
• pp.207-212
• /
• 2003

The field emission and luminescent properties of carbon nanotubes (CNTs) that were straightened out by argon ion irradiation were investigated. Argon ion irradiation permanently straightened out both as-grown and screen-printed CNTs in the presence of a strong electric field. The straightening process enhanced the emission properties of CNT films by showing a decrease in turn-on field, an increase in total emission current, and a stable emission. Furthermore, the number of emission sites was confirmed to increase by observing the luminescent properties of CNT films after the straightening. The mechanism involved in the straightening of the CNTs is proposed and the enhancement in field emission is discussed in detail.