• The Journal of Korean Physical Therapy
• /
• v.34 no.4
• /
• pp.155-160
• /
• 2022

Purpose: This study was to identify the effect of cervical stabilization exercise with visual feedback on the craniovertebral angle and foot pressure in subjects with forward head posture. Methods: Thirty healthy adults were recruited in the study. Participants were randomly assigned to the stabilization exercise with visual feedback (SE-VF) group (n=15) or stabilization exercise (SE) group (n=15). The SE-VF group performed cervical stabilization exercise while sitting on a chair without a backrest and checking their side profile in real time a monitor 3m away. The SE group performed the same cervical stabilization exercise as the SE-VF group accompanied by without visual feedback. Craniovertebral angle (CVA) was measured to quantify forward head posture, and the foot pressure of the subjects were evaluated. Results: The foot pressure showed statistically significant differences pre and post in both midfoot and left metatarsal only in SE-VF group (p<0.05). Conclusion: These findings of this study showed that the cervical stabilization exercise with visual feedback was effective for the foot pressure of subjects. In addition, based on the results of this study, it is suggested that visual feedback will be effective in cervical stabilization exercise.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.45 no.6
• /
• pp.117-122
• /
• 2008

Although the pulse diagnosis is the one of the most important diagnostic process to traditional medical doctors, there is no proper communication tool between experts and trainees. In this paper, we have developed a indentation training system which consists of a hardware measuring indent pressure on artificial arm quantitatively and a software providing a indentation training program. The hardware for measurement of indent pressure profile includes 3 load cells embedded in the artificial arm, signal amplification part and digitization part, NI-USB 6009 with 200Hz sampling rate. For setting up a relationship table between weights and output voltages, 8 standard weights were used. To evaluate this hardware, 3 oriental medical specialists were involved and their indent pressure profile were recorded three times respectively. From these, it was found that pulse diagnosis process could be divided into 3 periods and the maximum load were $500g{\cdot}f$ approximately while doctors perform a pulse diagnosis. The indentation training program was implemented with LabView and designed to monitor the differences between the pressure profile of a expert and that of a trainee so to offer some visual feedback to the trainee. Also, this program could provide the trends of training performances. With this developed system, the education of pulse diagnosis is expected to be more quantitative and effective.

• Tribology and Lubricants
• /
• v.28 no.4
• /
• pp.153-159
• /
• 2012

Tapered roller bearings are widely used in high axial-load and radial-load applications. In this study, a numerical analysis is performed to study a finite line contacts EHL problem between a tapered roller and raceway in tapered roller bearings. Converged solutions are obtained for moderate load and material parameters using a finite difference method with non-uniform grids and the Newton-Raphson method. The contours and sectional plots of pressure distribution and film shape are compared. The pressure distribution and film shapes near both ends of the roller are very different from those in the central part and are transversely asymmetric. The maximum pressure and absolute minimum film thickness always occur at the small end of the roller.

• Proceedings of the KSME Conference
• /
• 2001.06d
• /
• pp.989-994
• /
• 2001

Numerical simulations of high temperature catalytic combustion have been performed for the application to a gas turbine combustor. Dependences of inlet temperature and pressure on the distributions of temperature and species concentrations were investigated using plug flow model with detailed homogeneous and heterogeneous chemistries of methane-air mixtures. Honeycomb typecombustor deposited with Pt catalyst of 100mm in length and 26mm in diameter is used. The results show that rapid increase of temperature profile occurs earlier with the increase of inlet temperature and the decrease of inlet pressure. The condition which catalytic combustion is stabilized exists at certain range of inlet temperature and pressure. The state of catalytic combustion is also confirmed by the distributions of species concentration.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.12 no.2
• /
• pp.262-270
• /
• 1988

A numerical solution of the elastohydrodynamic lubrication problem for an axially profiled cylindrical roller is presented. The problem is analyzed using finite difference method and Newton-Raphson method. The effect of side leakage and compressibility of lubricants are considered and axially nonuniform grid is constructed over the computation zone. Isobars, contours and section graphs show pressure variation and film shape. Contours plot is very similar to the previously reported experimental observations based upon optical interferometry. The maximum pressure and the minimum film thickness occur near the start of the profiling. The method used makes it possible to design an optimum axial profile of the roller to increase the life of rolling bearings.

• Tribology and Lubricants
• /
• v.26 no.5
• /
• pp.263-271
• /
• 2010

The rollers of cylindrical roller bearing are axially profiled to relieve high edge stress concentration caused by mainly their finite length and by misalignment. In this paper, a numerical analysis is carried to study the EHL of misaligned (tilted) rollers with axially profiled ends. Using a finite difference method with non-uniform grids and the Newton-Raphson method, the highly nonlinear EHL problems are systematically solved. Physically consistent solutions are obtained for moderate load, material parameters and very small misalignment. For different misalignment angles, contours and sectional plots of pressure and film shape near both edge regions are compared. The asymmetric pressure distributions and film shapes show that the EHL results of finite line contacts are highly dependent upon very small amounts of roller misalignment. Especially, the effect of misalignment on the EHL pressure distribution is much higher than the film shapes.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.9 no.4
• /
• pp.131-136
• /
• 2000

This study deals with the mechanical properties of STS304-Al351 friction welding zone. Main results are as follows ; under the condition of upset pressure 75MPa, the tensile strength of STS304-al6351 friction weld interface was higher than that of Al6351 base metal, and the highest tensile strength(290MPa) was obtained at upset pressure 125MPa. The hardness profile across the weld interface shows that the hardness of both STS304 and Al6351 is higher around the weld interface, and sharply increased hardness on the STS304 side is related with the plastic deformation of micro volume. As the result of analyzing the tensile fracture, it showed perfect soft fracture.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.06a
• /
• pp.519-523
• /
• 2007

Gas(or methane) hydrates are solid solutions when water molecules are linked through hydrogen bonding and create host lattice cavities that can enclose a large variety of guest gas molecules. The natural gas hydrate crystal may exist at low temperature above the normal freezing point of water and high pressure greater than about 30 bars. A lot of quantities of natural gas hydrates exists in the earth and many production schemes are being studied. In the present investigation, depressurization method was considered to predict the production of gas and the simulation of the two phase flow - gas and water - in porous media is being carried out. The simulation show about the fluid flow in porous media have a variety of applications in industry. Results provide the appearance of gas and water production, the pressure profile, the saturation of gas/ water/ hydrates profiles and the location of the pressure front.

• Tribology and Lubricants
• /
• v.19 no.2
• /
• pp.85-93
• /
• 2003

In this study, a multigrid multi-integration method has been used to solve the steady-state, elastohydrodynamic lubrication (EHL) point contact problem of a ball joint mechanism used in small reciprocating compressors. Pressure and film thickness profiles have been calculated at minimum and maximum Moes M parameter conditions during one revolution of crankshaft. The effects of various lubricant viscosities, loads, ball velocities, elastic modulli, and radii of curvature on the calculated pressure distribution and film thicknesses have been investigated. The results indicate that the viscosity of lubricant, the sliding velocity of ball, and the reduced radius of curvature have considerable effects on the minimum and central film thicknesses. Solutions obtained with the multigrid analysis are compared with results calculated according to the Hamrock ＆ Dowson relations for the minimum and central film thicknesses.

• Proceedings of the KSME Conference
• /
• 2000.11b
• /
• pp.597-602
• /
• 2000

In a MEMS(micro-electro mechanical system), the fluid may slip near the surface of a solid and have a discontinuous temperature profile. A numerical prediction in this slip flow region can provide a reasonable guide for the design and fabrication of micro devices. The compressible Navier-Stokes equation with Maxwell/smoluchowski boundary condition is solved for two simple systems; couette flow and pressure driven flow in a long channel. We found that the couette flow could be regarded as an incompressible system in low speed regions. For the pressure driven flow system, we observed nonlinear distribution of pressure in the long channel and numerical results showed a good agreement with the experimental results.