• The Transactions of the Korean Institute of Power Electronics
• /
• v.27 no.2
• /
• pp.150-156
• /
• 2022

This study proposes a design method of fuel cell DC/DC converter using in 5-ton forklift. For efficient hydrogen usage, targeted fuel cell system recirculates discarded hydrogen after fuel cell reaction. Recirculating hydrogen contains much impurities that reduces output power, increasing pressure that can damage the internal fuel cell reaction system. The proposed DC/DC converter effectively converts fuel cell power considering the voltage drop rate to reflect the recirculating hydrogen. Then, frequency control method is used to regulate the current ripple amount for battery and fuel cell hybrid configuration. Proposed power converter system design and control methods are verified in a practical fuel cell system that implements recirculating hydrogen.

• Journal of international Conference on Electrical Machines and Systems
• /
• v.2 no.3
• /
• pp.342-348
• /
• 2013

As a number of wind power generation systems have been installed in power systems in the world, frequency fluctuations due to output power variations from wind farms have become a serious problem. Battery systems have been studied for smoothing the output variations and decreasing the resulting frequency fluctuations. Among these studies, efficient design of battery systems is one of the most important subjects from a point of view of cost. This paper presents a comparative analysis of the smoothing effect between the conventional moving average method and a new method based on frequency response analysis.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.2
• /
• pp.569-575
• /
• 2014

A highly efficient class E power amplifier is demonstrated for application to wireless power transfer system. The amplifier is designed with an L-type matching at the output for harmonic rejection and output matching. The power loss and the effect of each component in the amplifier with the matching circuit are analyzed with the current ratio transmitted to the output load. Inductors with a quality factor of more than 120 are used in a dc feed and the matching circuit to improve transmission efficiency. The single-ended amplifier with 20 V supply voltage shows 7.7 W output power and 90.8% power added efficiency at 6.78 MHz. The wireless power transfer (WPT) system with the amplifier shows 5.4 W transmitted power and 82.3% overall efficiency. The analysis and measurements show that high-Q inductors are required for the amplifier design to realize highly efficient WPT system.

• ETRI Journal
• /
• v.45 no.4
• /
• pp.570-580
• /
• 2023

Sensor nodes are the most significant part of a wireless sensor network that offers a powerful combination of sensing, processing, and communication. One major challenge while designing a sensor node is power consumption, as sensor nodes are generally battery-operated. In this study, we proposed the design of a low-power, long range-based wireless sensor node with flexibility, a compact size, and energy efficiency. Furthermore, we improved power performance by adopting an efficient hardware design and proper component selection. The Nano Power Timer Integrated Circuit is used for power management, as it consumes nanoamps of current, resulting in improved battery life. The proposed design achieves an off-time current of 38.17309 nA, which is tiny compared with the design discussed in the existing literature. Battery life is estimated for spreading factors (SFs), ranging from SF7 to SF12. The achieved battery life is 2.54 years for SF12 and 3.94 years for SF7. We present the analysis of current consumption and battery life. Sensor data, received signal strength indicator, and signal-to-noise ratio are visualized using the ThingSpeak network.

• Journal of KIISE:Computer Systems and Theory
• /
• v.27 no.2
• /
• pp.227-233
• /
• 2000

In this paper, we present a new high-level data path synthesis algorithm which solves the two design problems, namely, scheduling and allocation, with power minimization as a key design parameter. From the observations in previous works on data path synthesis for low power, we derive an integer programming (IP) formulation for the problem, from which we then develop an efficient heuristic to carry out the scheduling and allocation simultaneously. Our experimental results demonstrate that the proposed algorithm is very effective in saving power consumption of circuits significantly.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.11a
• /
• pp.1067-1072
• /
• 2003

Generally dual mass flywheel(DMF) is used as a solution to reduce noise and vibration of power train system and to improve the comfortability of passenger car. In this paper, design concept of new DMF model, analytical/numerical model, test procedure and tuning results are presented. Design parameters are studied by some numerical methods and tests. As the result, we can find more efficient model of DMF and reduce vibration level in power train system.

• Proceedings of the IEEK Conference
• /
• 2004.06a
• /
• pp.31-34
• /
• 2004

In wireless communication systems, low-power metrics is becoming a burdensome problem in the portable terminal design, because of portability constraints. This paper presents design architecture of a low-power partial correlation Digital Matched Filter for the IMT-2000 communication systems. The proposed approach focuses on efficient circuit size, power dissipation, maintaining the operating throughput. The proposed architecture was verified by using Xilinx FPGA.

• International Journal of Control, Automation, and Systems
• /
• v.3 no.3
• /
• pp.493-501
• /
• 2005

A power plant simulation tool ('PowerSim') has been developed with 10 years experience from the development of a plant simulator for efficient modeling of a power plant. PowerSim is the first developed tool in Korea for plant simulation with various plant component models, instructor station function and the Graphic Model Builder (GMB). PowerSim is composed of a graphic editor using general purpose design software, a netlist converter, component models, the scheduler, Instructor Station and an executive. The graphic editor generates a netlist that shows the connection status of the various plant components from the Simdiagram, which is drawn by Icon Drag method supported by GUI environment of the PowerSim. Netlist Converter normalizes the connection status of the components. Scheduler makes scheduling for the execution of the device models according to the netlist. Therefore, the user makes Simdiagram based on the plant Pipe and Instrument Drawing (P&ID) and inputs the plant data for automatic simulating execution. This paper introduces Graphic Model Builder (GMB), instructor station, executive and the detailed introduction of thermal-hydraulic modeling. This paper will also introduce basic ideas on how the simulation Diagram, based on netlist generated from general purpose design software, is made and how the system is organized. The developed tool has been verified through the simulation of a real power plant.

• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.519-520
• /
• 2008

In this paper, we design and implement the monolithic zero crossing detection power factor correction IC using a high voltage 30V BCD process. The ZCD PFC IC is designed for power applications, such as notebook, LCD monitor, etc. It includes power factor correction function and several protection circuit, regulator, high-voltage high current output drivers. And also, the designed IC has restart timer function which the output pulse is generated if the output signal of IC is not in a 200us. The simulation results show that the designed IC acts properly as power factor correction IC with efficient protective functions.

• Proceedings of the KIEE Conference
• /
• 2001.04a
• /
• pp.227-230
• /
• 2001

This paper deals with a bidirectional ac-dc converter used in ups system application. We propose a Voltage-Source-Charge-Pump-Power-Factor-Correction(VS-CPPFC) ac-dc converters. First of all, we propose a charge pump power-factor-correction converter. Secondly, we derive and analyse a unity power factor condition. The proposed topology is based on a half-bridge for the primary and a current-fed push pull for the secondary side of a high frequency isolation transformer. The advantage of bidirectional flow of power achieved by using the same power components is that the circuit is simple and efficient. And the galvanically isolated topology is specially attractive in battery charge/discharge circuits in ups system. We design equivalent model for the steady-state circuit and analyse operation waveforms for each mode. We show that the proposed model can be applied to ups system by simulation processes.