• Journal of Korean Society of Forest Science
• /
• v.42 no.1
• /
• pp.83-100
• /
• 1979

It was planned and performed to study the possibility on the use of inexpensive and easily acquirable foliage powder, which processed by pulverizing after dried, instead of imported expensive wheat flour for the extending of plywood adhesives. Pine leaves of softwood trees, Poplar, Oak and Sycamore leaves of broad leaved species were selected and harvested to pulverize into the minute foliage powder. The harvested foliages from each selected species were pulverized into 40 mesh particles after dried at $100{\sim}105^{\circ}C$ condition during 24 hours in drying oven. To compare the extending effect of plywood adhesives with these foliage powders 100 mesh wheat flour using at current plywood industry was also prepared. Foliage powder and wheat flour were extended into 10, 20, 30, 50 and 100% to the urea and phenol formaldehyde resin. After plywoods were processed by the above extending method shear strength of extended plywoods were analyzed and discussed. The results obtained at this study are as follows: 1) Among 10% extensions of urea formaldehyde resin plywood, dry shear strength of plywood extended by wheat flours was the highest and that of non-extended plywood the next. Plywood extended with foliage powder showed the lowest dry shear strength. The order of dry shear strength of plywoods extended by foliage powder was that of Oak foliage powder extension, the best, that of Sycamore, that of Pine, and that of Poplar. 2) Among 20% extensions of urea formaldehyde resin plywood, plywood extended by wheat flour showed the highest dry shear strength, and the next was plywood by Poplar foliage powder. All these two showed higher dry shear strength than non-extension plywoods. Except Poplar, dry shear strength of foliage powder extension plywoods was bad, but the order of dry shear strength of plywoods extended by foliage powder was Pine, Poplar and Oak. 3) In the case of 30% extensions of urea formaldehyde resin plywood, dry shear strength of wheat flour extension was the highest and non-extension the next. Dry shear strength of foliage powder extension plywoods was poor with a rapid falling-off in strength. 4) Among 50% and 100% extensions of urea formaldehyde resin plywood, only wheat flour showed excellent dry shear strength. In the case of foliage powder extension, low dry shear strength showed at the 50% extension of Pine and Poplar, and plywoods of 50% extension of Oak foliage powder delaminated without measured strength. All plywoods of 100% foliage powder extension delaminated, and then shear strength were not measured. 5) Among wet shear strength of 10% extensions of urea formaldehyde resin plywood, wheat flour extension was the highest as in the case of dry shear strength, and non-extension plywood the next. Except Poplar foliage extension, all foliage powder extension plywoods showed low shear strength. 6) Wet shear strength of plywoods of 20% extension lowered in order of non-extension plywood, plywood of wheat flour extension and plywood of foliage powder extension, but other plywoods of foliage powder extension except plywoods of Poplar and Oak foliage powder extension delaminated. 7) Wet shear strength of 30% or more extension of urea formadehyde resin plywood were weakly measured only at 30% and 50% extension of wheat flour, and wet shear strength of plywoods extended by foliage powder were not measured because of delaminating. 8) Dry shear strength of phenol formaldehyde plywoods extended by 10% wheat flour was the best, and shear strength of plywoods extended by foliage powder were low, but the order was Oak, Poplar, and Pine. Plywood of Sycamore foliage powder extension delaminated. 9) In the case of 20% extensions of phenol formaldehyde resin, dry shear strength of plywood extended by wheat flour was the best, but plywood of Pine foliage powder extension the next, and the next order was Oak and Poplar foliage powder. Plywood of Sycamore foliage powder extension delaminated. 10) Among dry shear strength of 30% extensions of phenol formaldehyde plywood, that of Pine foliage powder extension was on the rise and more excellent than plywood of wheat flour extension, but Poplar and Oak showed the tendency of decreasing than the case of 20% extension. Plywood of Sycamore foliage powder extension delaminated. 11) While dry shear strength of 50% and 100% extension plywoods were excellent in the case of Pine foliage powder and wheat flour extension, that of hardwood such as Poplar, Oak, and Sycamore foliage powder extension were not measured because of delaminating. 12) As a filler the foliage powder extension of urea formaldehyde resin is possible up to 20% with Poplar foliage powder. And also as an extender for phenol formaldehyde resin, Pine foliage powder can be added up to the same amount as that in the case of wheat flour.

• Korean Chemical Engineering Research
• /
• v.54 no.4
• /
• pp.494-500
• /
• 2016

In order to remove acetyl group from yellow poplar, deacetylation was performed using sodium hydroxide (NaOH) prior to oxalic acid pretreatment. During the deacetylation ($60^{\circ}C$ for 80 min, 0.8% NaOH), most of the acetyl group were removed from hemicellulose. Simultaneous saccharification and fermentation (SSF) and semi-SSF were carried out based on solid loading (10, 12.5, 15%) of deacetylated biomass and pre-hydrolysis with enzymes (0, 6, 12, 24 h). The highest ethanol was obtained as 26.73 g/L after 120 h when 10% of biomass was used for SSF. It is corresponding to 88.41% of theoretical ethanol yield. At the 12.5% and 15% of biomass loading, the highest ethanol was obtained from 6 h pre-hydrolysis. It was 32.34 g/L and 27.15 g/L, respectively, and corresponding to ethanol yield of 85.58 and 59.87%. In order to remove fermentation inhibitors from hydrolysates, overliming was performed using calcium hydroxide ($Ca(OH)_2$). The highest ethanol was 5.28 g/L after 72 h of fermentation.

• Journal of Korean Society of Forest Science
• /
• v.71 no.1
• /
• pp.45-49
• /
• 1985

Protoplast-source meterial and enzyme strength had a significant influence on protoplast yield from hybrid poplar, Populus alba ${\times}$ P. grandidentata. The yield of protoplasts from in vitro culture of 1 month-old plantlets was more than that from greenhouse grown 4 month-old stock plant. In vitro cultured plantlets regulary produced more viable protoplasts with E-I enzyme solution (0.5% cellulase and 0.1% macerase) than those with E-II enzyme solution (1.0% cellulase and 0.2% macerase) after overnight incubation. The mean yield of protoplasts from in vitro cultured plantlets was $4{\times}10^6$ with E-I enzyme solution. Cell division was observed in these protoplast cultures after 7-10 days. Protoplast-derived hybrid poplar cells survived over 3 weeks in culture and some continuous cell divisions were evident. Other aspects associated with protoplasts from in vitro cultured plantlet are also discussed.

• Journal of Korean Society of Forest Science
• /
• v.101 no.4
• /
• pp.613-618
• /
• 2012

The 5-year-old seedlings and emblings which regenerated from somatic embryos were compared to the height, DBH, foliar characteristics, content of chlorophyll (chlorophyll a, b and total chlorophyll), carotenoid and leaf microstructure in Liriodendron tulipifera. In comparison of height and DBH (diameter at breast height), no significant differences were found in height (seedling, 3.8 m; embling, 3.87 m) and DBH (seedling, 12.09 cm; embling, 12.53 cm). The emblings and seedlings were similar in values of length (seedling, 108.11 mm, embling, 113.59 mm), width (seedling, 149.1 mm; embling, 167.71 mm), surface area (seedling, $119.92mm^2$; embling, $164.43mm^2$), fresh weight (seedling, 2.1 g; embling, 2.62 g) of leaf, and length (seedling, 81.49 mm; embling, 98.41 mm) and thickness (seedling, 1.66 mm; embling, 1.98 mm) of petiole. In case of chlorophyll content in the leaves, the chlorophyll a (seedlings, $11.2{\mu}g/g$; emblings, $13.2{\mu}g/g$), b (seedlings, $4.8{\mu}g/g$; emblings, $5.4{\mu}g/g$) and total content were higher in emblings ($930.2{\mu}g/g$) than seedlings ($800.1{\mu}g/g$), however, content of carotenoid (seedlings, $260.3{\mu}g/g$; embling, $265.2{\mu}g/g$) showed similar in both plants. Leaves of emblings had a similar pattern of histological structure (palisade or sponge parenchyma) to that of seedlings leaves. Therefore, the results showed that there were no remarkable growth differences when compared with 5-year-emblings and seedlings of yellow poplar.

• Journal of Korean Society of Forest Science
• /
• v.94 no.1 s.158
• /
• pp.39-44
• /
• 2005

An effective micropropagation system for Liriodendron tulipifera L via somatic embryogenesis was established using immature seeds. Immature seeds from five individual trees were bisected longitudinally and cultured on two basal media (MS and B5) containing different combinations of 2,4-D and TDZ to induce callus and embryogenic tissue under light ($40{\mu}mol\;m^{-2}s^{-1}$, 16 hr/day) or complete darkness at $25{\pm}2^{\circ}C$. There was no distinctive difference on callus and embryogenic tissue induction between the two basal media with PGRs. Optimum culture medium appeared to be MS medium supplemented with 1.0mg/L 2,4-D and 0.01mg/L TDZ plus 3% sucrose. Nonembryogenic callus induction rate was not significantly different among the genotypes. However, However, the embryogenic callus induction frequency differed greatly by the genotypes ranging from 55% to 72% when cultured in the dark. Generally, the cultures maintained in the dark tended to show normal somatic embryo development as well as embryogenic tissue formation and this was confirmed by histological examination. Above results suggest that a proper selection of mother tree and dark culture condition are necessary to optimize somatic embryogenesis system of Liriodendron tulipifera.

• Journal of Korean Society of Forest Science
• /
• v.98 no.3
• /
• pp.242-246
• /
• 2009

We examined sapflow of two populus tree species (Populus alba ${\times}$ Populus glandulosa and Populus euramericana) grown under Swine wastewater treatment, and measured relationship between sapflow and climate facters. Sapflow of P. euramericana was 1.5 times greater than that of P. alba ${\times}$ P. glandulosa from September to late December 2007. However, sapflow of P. euramericana and P. alba ${\times}$ P. glandulosa was similar after late January. The relationship between the mean temperature and sapflow was relatively high. There was a decrease in sapflow tendency of the two poplar species during the late October when the mean temperature was low. Trends on relationship between the relative humidity and sapflow showed low relationship. However, data showed weak relationship between sapflow and precipitation. During the period of less precipitation, sapflow of P. alba ${\times}$ P. glandulosa has no relationship. Sapflow of two populus species was still active during non-growing season. P. euramericana was considered as a better species than P. alba ${\times}$ P. glandulosa, in terms of phytoremediation.

• The Korean Journal of Mycology
• /
• v.26 no.2 s.85
• /
• pp.194-199
• /
• 1998

Pholiota sp. were collected from the forest of Kangwon province (Mt. Samak, Mt. Odae and Kangwon National University Forest Experimentation) from the early of August to the end of October 1997. Among these fungi, Poliota adiposa was selected for culture experiment because it is suitable for edible mushroom. The Optimal temperature for the mycelial growth of Pholiota adiposa was in the range of $28^{\circ}C$ while that of fruit body formation was $15{\pm}1^{\circ}C$. Brown sugar as carbon source and soybean flour as nitrogen source were good for mycelial growth in commercial liquid culture. The fruit bodies of Pholiota adiposa were artifitially produced on plastic bottle including poplar sawdust and rice bran (4:1).

• Korean Journal of Plant Resources
• /
• v.18 no.3
• /
• pp.403-409
• /
• 2005

Mature nodal segments of 2-year-old greenhouse stock plant were cultured on Murashige and Skoog basal medium supplemented with the different kinds and various concentrations of cytokinins to produce multiple shoots in in vitro condition. The most adventitious shoots were produced from excised ends of nodal segments. The highest average number $(24.6\;{\pm}\;4.6)$ of shoots was produced with the combination of BA 1.0mg/L and TDZ 0.1mg/L in MS medium. In addition, several shoots were formed from lenticels of bark cambium with the same treatment. These concentrations promoted high shooting capability upto $94.6\%$ and NAA was the best cytokinin among five different PGR sources.

• Journal of the Korean Wood Science and Technology
• /
• v.29 no.4
• /
• pp.103-110
• /
• 2001

Bio-kraft pulping of Populus alba${\times}$glandulosa pretreated with white-rot fungus, Phanerochaete chrysosporium KCCM 34740, was investigated The biopulping efficiency was evalued based on fungal pretreatment time and properties of bio-kraft pulp (pulp yield, freeness, WRY, kappa number and brightness) in comparison to the controls. Pretreatment of poplar wood chips with Phanerochaete chrysosporium KCCM 34740 for 10days resulted in a some increase in screened yield (by 2%). According to increase of fungal incubation time, decrease in freeness (CSF) and increase in WRY were observed And bio-kraft pulping also led to improvement of physical properties of handsheet. As a result of bio-beating effect, we expect the saving of chemicals in kraft cooking process and energy consumption in beating process.

• Journal of Korean Society of Forest Science
• /
• v.7 no.1
• /
• pp.35-39
• /
• 1968

1. The Fall webworm, Hyphantria cunea was widely distributed ranging from Seoul to Kangnung, Yung-ju, Taegu, Iri and Kwang-ju in 1967. 2. Heavily infested tree species by the Fall webworm were Sycamore, Cherry, ash-leaved maple, poplar, and elm. 3. The average number of larval masses per damaged garden tree and roadside tree was 7.0 and 3.4 respectively. 4. Trees of 6-10m in height had most number of larval masses and were most heavily infested. 5. More larval masses were found in the median and lower parts than higher parts of the crown. 6. The ratio of damaged by second generation was 55% higher than by first generation. The ratio of damage by 3rd generation is 18% less than by first generation.