• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08a
• /
• pp.749-751
• /
• 2007

A buffer layer consisting of $SiO_x/Ta/Ti$ has been developed in order to overcome the adhesion and stress problems between poly-Si film and mica. Polycrystalline silicon thin film transistor was successfully fabricated on the mica and transferred to a flexible plastic substrate.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.50-54
• /
• 2004

A numerical system to extract effective elastic properties of polycrystalline thin-films for MEMS devices is already developed. In this system, the statistical model based on lattice system is used for modeling the microstructure evolution simulation and the key kinetics parameters of given micrograph, grain distributions and deposition process can be extracted by inverse method proposed in the system. In this work, the effects of kinetics parameters on the extraction of effective elastic properties of polycrystalline thin-films are studied by using statistical method. The effects of the fraction of the potential site( $f_{P}$ ) and the nucleation probability( $P_{N}$ ) among the parameters for deposition process of microstructure on the extraction of effective elastic properties of polycrystalline thin-films are studied.d.d.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.243.2-243.2
• /
• 2016

Tungsten (W) is recently gaining attention as a potential candidate to replace Cu in semiconductor metallization due to its expected improvement in material reliability and reduced resistivity size effect. In this study, the impact of electron scattering at grain boundaries in a polycrystalline W thin film was investigated. Two nominally 300 nm-thick films, a (110)-oriented single crystal film and a (110)-textured polycrystalline W film, were prepared onto (11-20) Al2O3 substrate and thermally oxidized Si substrate, respectively in identical fabrication conditions. The lateral grain size for the polycrystalline film was determined to be $119{\pm}7nm$ by TEM-based orientation mapping technique. The film thickness was chosen to significantly exceed the electron mean free path in W (16.1 and 77.7 nm at 293 and 4.2 K, respectively), which allows the impact of surface scattering on film resistivity to be negligible. Then, the difference in the resistivity of the two films can be attributed to grain boundary scattering. quantitative analyses were performed by employing the Mayadas-Shatzkes (MS) model, where the grain boundary reflection coefficient was determined to be $0.42{\pm}0.02$ and $0.40{\pm}0.02$ at 293 K and 4.2 K, respectively.

• Proceedings of the KIEE Conference
• /
• 2006.07c
• /
• pp.1313-1314
• /
• 2006

The polycrystalline 3C-SiC thin films heteroepitaxially grown by LPCVD method using single precursor 1,3-disilabutane at $850^{\circ}C$. The crystallinity of the 3C-SiC thin film was analyzed by XRD and FT-IR. Residual strain was investigated by Raman scattering. The surface morphology was also observed by AFM and voids or dislocations between SiC and $SiO_2$ were measured by SEM. The grown poly 3C-SiC thin film is very good crystalline quality, surface like mirror, and low defect and strain. Therefore, the polycrystalline 3C-SiC is suitable for harsh environment MEMS applications.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.5 no.1
• /
• pp.67-77
• /
• 1995

Abstract The principal factor affecting the increased penetration of photovoltaics into the marketplace is cost. For traditional crystalline silicon modules, half of the cost is that of the silicon wafers. As a result much effort has centered on reducing this cost by the use of thin film technologies. Substantial technical progress has been made towards improving the efficiencies of polycrystalline thin film solar cells to reduce the production costs. Progress in semiconductor deposition techniques has also been rapid. The most mature of these are based on polycrystalline silicon (p - Si), amorphous silicon (a - Si), copper indium diselenide $SuInSe_2$(CIS), and cadmium telluride (CdTe). This paper explores the recent advances in the development of polycrystalline thin film solar cells.

• Journal of the Korean Physical Society
• /
• v.73 no.9
• /
• pp.1329-1333
• /
• 2018

We investigated the mechanism of mobility enhancement after the dehydrogenation process in polycrystalline silicon (poly-Si) thin films. The dehydrogenation process was performed by using an in-situ CVD chamber in a $N_2$ ambient or an ex-situ furnace in air ambient. We observed that the dehydrogenated poly-Si in a $N_2$ ambient had a lower oxygen concentration than the dehydrogenated poly-Si annealed in an air ambient. The in-situ dehydrogenation increased the (111) preferred orientation of poly-Si and reduced the oxygen concentration in poly-Si thin films, leading to a reduction of the trap density near the valence band. This phenomenon gave rise to an increase of the field-effect mobility of the poly-Si thin film transistor.

• Electrical & Electronic Materials
• /
• v.8 no.5
• /
• pp.619-625
• /
• 1995

Polycrystalline CdTe thin film has been studied for photovoltaic application due to the 1.45 eV band gap energy ideal for solar energy conversion and high absorption coefficient. The formation of low resistance contact to p-CdTe is difficult because of large work function(>5.5eV). Common methods for ohmic contact to p-CdTe are to form a p+ region under the contact by in-diffusion of contact material to reduce the barrier height and modify a p-CdTe surface layer using chemical treatment. In this study, the surface chemical treatment of p CdTe was carried out by H$\_$3/PO$\_$4/+HNO$\_$3/ or K$\_$2/Cr$\_$2/O$\_$7/+H$\_$2/SO$\_$4/ solution to provide a Te-rich surface. And various thin film contact materials such as Cu, Au, and Cu/Au were deposited by E-beam evaporation to form ohmic contact to p-CdTe. After the metallization, post annealing was performed by oven heat treatment at 150.deg. C or by RTA(Rapid Thermal Annealing) at 250-350.deg. C. Surface chemical treatments of p-CdTe thin film improved metal/p-CdTe interface properties and post heat treatment resulted in low contact resistivity to p-CdTe.Of the various contact metal, Cu/Au and Cu show low contact resistance after oven and RTA post-heat treatments, respectively.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.129-134
• /
• 2004

The development of fabrication processes of polycrystalline-silicon-thin-film transistors (poly-Si TFTs) at low temperatures is reviewed. Rapid crystallization through laser-induced melt-regrowth has an advantage of formation of crystalline silicon films at a low thermal budget. Solid phase crystallization techniques have also been improved for low temperature processing. Passivation of $SiO_2$/Si interface and grain boundaries is important to achieve high carrier transport properties. Oxygen plasma and $H_2O$ vapor heat treatments are proposed for effective reduction of the density of defect states. TFTs with high performance is reported.

• The Korean Journal of Ceramics
• /
• v.3 no.4
• /
• pp.249-252
• /
• 1997

Highly oriented ZnO thin films were fabricated by dip-coating technique using zinc acetate 2-methoxyethanol 2-aminoethanol solution as starting materials, and effects of substrates on the film's orientation were investigated. Product films were obtained by prefiring at 300, 400, 500 and 550℃ for 10 min, followed by final heat-treatment at the same temperatures as prefiring for 1h. c-axis oriented films on glass substrates were prepared by heat treatment of prefiring films at 300-550℃, while films on alumina showed polycrystalline structure. Films with c-axis orientation exhibited lower specific resistivities than those of polycrystalline films with partial crack and pore.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.332-333
• /
• 2008

DC magnetron sputtering was used to deposit p-type polycrystalline silicon on n-type Si(100) wafer. The influence of film microstructure properties on deposition parameters (DC power, substrate temperature, pressure) was investigated. The substrate temperature and pressure have the important influence on depositing the poly-Si thin films. Smooth ploy-Si films were obtained in (331) orientation and the average grain sizes are ranged in 25-30nm. The grain sizes of films deposited at low pressure of 10mTorr are a little larger than those deposited at high pressure of 15mTorr.