• Journal of the Korean Society of Combustion
• /
• v.17 no.4
• /
• pp.60-65
• /
• 2012

The MILD combustion and pollutant emission characteristics were investigated computationally. The temperature of supplying air-stream and mixing rate (${\Omega}$) of exhaust gas in the air-stream were adjusted to investigate the effects of those parameters on the MILD combustion in jet flow field. The emission indices for NO (EINO) and CO (EICO) were introduced to quantify the amount of those species emitted from the combustion. The high-temperature region disappeared gradually as the mixing rate increased for fixed air-stream temperature. The EINO increased as the air-stream temperature became higher for fixed mixing rate, and the EINO decreased dramatically with increasing the mixing rate for each air-stream temperature condition. The EICO also decreased with increasing the mixing rate and it was nearly independent of air-stream temperature except for near ${\Omega}$ = 0.7. It was found that the CO supplied in the air-stream can be destroyed in the MILD combustion over the certain mixing rate.

• Journal of Korean Society on Water Environment
• /
• v.29 no.3
• /
• pp.383-392
• /
• 2013

In this research, mixing behavior of the floating pollutant such as oil spill accidents was analyzed by studying the advection-diffusion of GPS floaters at water surface. The LPT (Lagrangian Particle Tracking) model of EFDC (Environmental Fluid Dynamics Computer Code) was used to simulate the motion of the GPS floater tracer. In the field experiment, 35 GPS floaters were injected at the Samun Bridge of Nakdong River. GPS floaters traveled to downstream about 700 m for 90 minutes. The field data by the GPS floater experiments were compared with the simulation in order to calibrate the parameter of LPT model. The turbulent diffusion coefficient of LPT model was determined as $K_H/hu^*$ = 0.17 from the scatter diagram. The arrival time of peak concentration and transverse diffusion from the simulation results were similar with the experiments from the concentration curves. Numerical experiments for anticipation of damage from floating pollutant were conducted in the same reach of the Nakdong River and the results show that the pollutant cloud transported to the left bank where the Hwawon pumping station is located. For this reason, it is suggested that the proper action should be needed to maintain the safety of the water withdrawal at the Hwawon pumping station.

• Atmosphere
• /
• v.34 no.3
• /
• pp.283-304
• /
• 2024

This study analyzed the variability and correlation between ground-level air pollutant concentrations and the atmospheric mixing layer height using data from four types of air pollutants (PM_2.5, PM₁₀, NO₂, and O₃) collected at AirKorea monitoring stations nationwide over a five-year period (2018~2022), and aerosol backscatter data observed by the Vaisala CL31 to derive atmospheric mixing layer heights. The five-year trends and variability of ground-level air pollutant concentrations under seasonal and hourly conditions were examined, as well as the seasonal distribution and diurnal variation of the atmospheric mixing layer height. Five correlation coefficient methodologies were applied to analyze the correlations between ground-level air pollutants and atmospheric mixing layer height under various seasonal and hourly conditions, confirming the dilution effect of the atmospheric mixing layer height. The results showed that PM_2.5, PM₁₀, and NO₂ generally had negative correlations with the atmospheric mixing layer height, while O₃ showed a strong positive correlation up to an altitude of 1,200~1,500 meters, and a negative correlation beyond that altitude. It was also shown that a single high concentration event (e.g., PM₁₀) can alter the overall correlation. The correlation can also vary depending on the characteristics of the correlation coefficient methodology, highlighting the importance of applying the appropriate methodology for each case during the analysis process.

• Journal of Environmental Science International
• /
• v.3 no.1
• /
• pp.31-38
• /
• 1994

The diffusion of the pollutants released into atmosphere is dependent on its chemical reaction, topography and micrometeorological characteristics. The purpose of the study is to investigate how much micrometeorological characteristics such as stability, wind speed and mixing height affect the diffusion of the air pollutants. For this purpose, this paper let 1) the basic theory be K-theory, 2) eddy diffusivity and wind speed be dependent on mixing height and stability, and 3) Grout method be used for numeric calculation. The result was 1) the more unstable condition, the higher mixing height and the higher wind speed we, the lower pollutants concentration appears, 2) the most intensive effect on the distribution of the pollutant concentration is the atmospheric stability.

• International Journal of Highway Engineering
• /
• v.15 no.6
• /
• pp.1-9
• /
• 2013

PURPOSES : About 35% of air pollutant is occurred from road transport. NOx is the primary pollutant. Recently, the importance of NOx removal has arisen in the world. $TiO_2$ is very efficient for removing NOx by photocatalytic reaction. The mechanism of removing NOx is the reaction of photocatalysis and solar energy. Therefore, $TiO_2$ in concrete need to be contacted with solar radiation to be activated. In general, $TiO_2$ concrete are produced by substitute $TiO_2$ as a part of concrete binder. However, 90% of $TiO_2$ in the photocatalysis can not contacted with the pollutant in the air and solar radiation. Coating and penetration method are attempted as the alternative of mixing method in order to locate $TiO_2$ to the surface of structure. METHODS : The goal of this study was to attempt to locate $TiO_2$ to the surface of concrete, so we can use the concrete in pavement construction. The distribution of $TiO_2$ along the depth were confirmed by basing on the comparison of $TiO_2$ compare by using the EDAX(Energy Dispersive X-ray Spectroscopy). RESULTS : $TiO_2$ were distributed within 3mm from concrete surface. This distribution of $TiO_2$ is desirable, since the $TiO_2$ induce photocatalysis are located to where they can be contacted with the air pollutant and solar radiation. CONCLUSIONS : Nano size $TiO_2$ is easily penetration in the top 3mm of concrete surface. By the penetration $TiO_2$ concrete can be produced with the use of only 10% of $TiO_2$, by comparing the mixing types.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.29 no.3B
• /
• pp.221-230
• /
• 2009

In Korea, many water intake plants are easily affected by effluents of sewage treatment plants because sewage treatment plants are usually located upstream or nearby the plants of the same riverine area. Furthermore, the inflow of harmful contaminants owing to pollutant spills or transportation accidents of vehicles using the roads and bridges intersecting the river causes significant impact on the management of water intake plants. Paldang lake, the main water intake plants in Korea, is especially exposed to various water pollution accidents, because the drainage basin area is significantly large compared to the water surface area of the lake. Therefore it is necessary to predict the possible pollutant spill in advance and consider measurements in case of water pollution. In this study, water quality prediction was performed in Paldang Lake in Korea durig the dry season using two-dimensional numerical models. In order to represent the cases of pollutant accidents, the difference of pollutant transport patterns with varying injection points was analyzed. Numerical simulations for hydrodynamics of water flow and water quality predictions were performed using RMA-2 and RAM4 respectively. As a result of simulation, the difference of pollutant transport with the injection points was analyzed. As a countermeasure against the pollutant accident, the augmentation of the flow rate is proposed. In comparison with the present state, the rapid dilution and flushing effects on the pollutant cloud could be expected with increase of flow rate. Thus, increase of flow rate can be used for operation of water intake plants in case of pollutant spill accidents.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.28 no.2
• /
• pp.146-153
• /
• 2004

A Promising new approach to achieve low pollutant emissions and improvement of flame stability is tested experimentally using a cyclone jet hybrid combustor employing both premixed and diffusion combustion mode. Three kinds of nozzle are tested for mixing enhancement of fuel and air. The LNG (Liquified Natural Gas) is used as a fuel. The combustor is operated by two methods. One is DC (Diffusion Combustion) mode generated swirl flow by air as general swirl combustor, and the other is HC (Hybrid Combustion) mode. The HC mode consists of diffusion jet flame of axial direction and premixed cyclone flame of tangential direction in order to stabilized the diffusion jet flame. The results showed that the flame stability of HC mode is significantly enhanced than that of DC mode through the change of mixing characteristics by modifications of fuel nozzle. In addition, the reductions of CO and NOx emission in HC mode, as compared with that for the DC mode, is large than about 50% in stable region. Also, even using the low calorific fuel as $CO_2$-blended gas, it is identified that the cyclone jet hybrid combustor has the high performance of flame stability.

• 보존과학연구
• /
• s.20
• /
• pp.121-137
• /
• 1999

Among pigment used at work of Dan-Chung, Emerald Green is specific illuminating fluorescent light of green. It is very difficult to change other organic or inorganic pigment. All of the internal high class pigment has rare light. But Emerald Green is superior to fresh color and stability out of industrial chemical products. It forms over 50% of quantity and importance of a pattern painting. Emerald Green prohibited to produce because of its toxicpollutants, so required to changing pigment development. It is characterized to excellent color, convenient work, economical, against-sunlight, against-air pollutant and durability. The result of a test is follows; 1. We are investigated into producing internal natural Emerald Green, import external pigment and industrial synthesis method etc. but unable to buy because of its toxic pollutant. 2. We are made six samples by yellowish and green is hpigment mixing. We tested on against sunlight and air pollutant. The best mixing ratio is follows. Titanium Dioxide R760 : 18g- Chalk, White Wash : 10g- Permanent Yellow : 7g- Cyanine Green : 8g- Chrome Yellow : 3g- Resin(Vehicle) : Acryl Emulsion(Styrene + 2-Ethyl HexylAcrylate + Methyl Meth Acrylate) 8%

• Journal of Korea Water Resources Association
• /
• v.54 no.7
• /
• pp.495-507
• /
• 2021

With the recent industrial development, accidental pollution in riverine environments has frequently occurred. It is thus necessary to simulate pollutant transport and dispersion using water quality models for predicting pollutant residence times. In this study, we conducted a field experiment in a meandering reach of the Sum River, South Korea, to validate the field applicability and prediction accuracy of RAMS+ (River Analysis and Modeling System+), which is a two-dimensional (2D) stream flow/water quality analysis program. As a result of the simulation, the flow analysis model HDM-2Di and the water quality analysis model CTM-2D-TX accurately simulated the 2D flow characteristics, and transport and mixing behaviors of the pollutant tracer, respectively. In particular, CTM-2D-TX adequately reproduced the elongation of the pollutant cloud, caused by the storage effect associated with local low-velocity zones. Furthermore, the transport model effectively simulated the secondary flow-driven lateral mixing at the meander bend via 2D dispersion coefficients. We calculated the residence time for the critical concentration, and it was elucidated that the calculated residence times are spatially heterogeneous, even in the channel-width direction. The findings of this study suggest that the 2D water quality model could be the accidental pollution analysis tool more efficient and accurate than one-dimensional models, which cannot produce the 2D information such as the 2D residence time distribution.

• The Journal of the Korea Contents Association
• /
• v.20 no.12
• /
• pp.537-546
• /
• 2020

This study deals with the development and improvement of a particle dispersion model for quick response to water pollutant accidents. The developed model is based on the shear dispersion theory where vertical mixing is done by step by step mixing by vertical and molecular diffusion algorithm. For the quick response to chemical accidents, an algorithm for multi-core modeling for the particle dispersion model is applied. After the application of multi-core operation using OpenMP directives to the model, the relation for the calculation time and particle size were determined along with the number of cores used for parallel programming to determine the model time for chemical accident responses. The results showed the adequate conditions for the modeling of chemical accidents for quick response and to increase the applicability of the model.